Re: UDB RH6.0 CD install problems with initial console

["Matthew Monacelli" <mam1281 rit edu>]

OK.  Now which ramdisk.img can/should I use (internet address?).  Also, I
have an x86 with Linux installed, might I have better luch writing the image
from there?  Only problem is I don't have a SCSI controller on the x86, I
might have to bring the drive to a friends unless there is a way to access
the drive accross my LAN when it is still connected to the UDB.  Hmm, it's a
thinker.  Any other ideas?

----- Original Message -----
From: "Rich Payne" <rdp@talisman.alphalinux.org>
To: "Matthew Monacelli" <nestle579@hotmail.com>
Cc: <axp-list@redhat.com>
Sent: Friday, December 17, 1999 8:43 AM
Subject: Re: UDB RH6.0 CD install problems with initial console


On Fri, 17 Dec 1999, Matthew Monacelli wrote:

> I thought I made it quite clear that I do not have a floppy drive.  Is
there
> a way to extract the ramdisk floppy image to the external hard drive?

You did, my appologies for not reading the entire message, my fault.

In theory I guess you could make a partition on the harddisk, rawrite the
image file to the partition (using rawrite under NT, will it let you
rawrite to a HDisk partition?), and then pass Linux the HDisk parition as
the root fs, you'll still need the load_ramdisk=1 line.

worth a try I guess.

--rdp

> ----- Original Message -----
> From: "Rich Payne" <rdp@talisman.alphalinux.org>
> To: "Matthew Monacelli" <nestle579@hotmail.com>
> Cc: "axp-list" <axp-list@redhat.com>; <recipient list not shown: ;>
> Sent: Friday, December 17, 1999 8:28 AM
> Subject: Re: UDB RH6.0 CD install problems with initial console
>
>
> On Fri, 17 Dec 1999, Matthew Monacelli wrote:
>
> > Hello all.  I have a Multia 166 and a SCSI CDROM and two SCSI HD's (9GB
> and
> > 2GB).  The 2GB is blank and I have installed NT4 Server on the 9GB drive
> > since I couldn't get Linux going right away.  I got as far as booting
the
> > kernel (generic.gz) and it finds the SCSI devices, video, etc (even with
> the
> > Tux graphic) until I get the "Warning: Unable to open initial console"
> error
> > mesage.  All I can do from there is 3-finger solute back toMILO (which I
> am
> > starting from ARC).  I have been searching through the list archive
trying
> > to find a solution but all I can find is "use the floppies".  Well, I
> don't
> > have a floppy drive so that doesn't work for me.  The 2GB HD is totally
> open
> > to putting anything on it that would allow to me to install RH6.0.  Any
> help
> > is very much appreciated.
>
>
> Use a floppy as the ramdisk instead of the CD. This should allow you to
> install.
>
> --rdp
>
> > Matt Monacelli
> >
> > --
> > To unsubscribe: send e-mail to axp-list-request@redhat.com with
> > 'unsubscribe' as the subject.  Do not send it to axp-list@redhat.com
> >
>
> Rich Payne
> rpayne@alphalinux.org www.alphalinux.org
>
>

Rich Payne
rpayne@alphalinux.org www.alphalinux.org

--
To unsubscribe: send e-mail to axp-list-request@redhat.com with
'unsubscribe' as the subject.  Do not send it to axp-list@redhat.com