Problems on installing Win95...

[Rafael Peregrino da Silva <rafael bmt4 kf tu-berlin de>]

Hi Folks!

I'm new on this discussion list and already bringing problems to you :-)

I'm trying to install Win95 with bochs and when I initialize the
installation process ('bochs boot:a', where 'floppya' is an image file of
a 1.44M floppy disk I have copied the Win95 Setup Disk to) I get the
following message: 

--------------------------------------------------------------------------------

#(0)BX_CPU_C::BX_CPU_C(void) called
# state_file::state_file()
# using rc file '.bochsrc'.
# ips = 1000000
#(0) BX_MEM_C::init_memory(int): allocating memory.
#(0)   memsize = 33554432
#(0) load_ROM: ROM BIOS 'bios/BIOS-bochs-990623a', size=65536 read into 
memory at 000f0000
#(0) load_ROM: ROM BIOS 'bios/VGABIOS-elpin-2.20', size=32768 read into 
memory at 000c0000
[cmos] Setting initial clock to: Tue Aug 10 21:57:50 1999
Opening image for device 0
# bx_options.floppy_command_delay = 50000
# default_depth = 16
vga: interval=300000
TTY not used, serial port is not connected
#(0) get_memory_in_k() = 32768
# WARNING: X11: bx_gui_c::exit() not implemented yet.
bochs exited, log file was './bochs.out'
# state_file::~state_file()
#(0)BX_CPU_C::~BX_CPU_C(void) called

--------------------------------------------------------------------------------

I've read that there's a bug on installing Win95 during device detection. 
I suspect, from other previous error messages and from the log file below, 
this can be my problem. 

--------------------------------------------------------------------------------
File "bochs.out"

0 font_width = 8
0 font_height = 16
0 waiting for MapNotify
0 MapNotify found.
bochs: panic, could not open IO init file.
0 Last time is 934322270
0
CPU:0
0 real mode
0 CS.d_b = 16 bit
0 SS.d_b = 16 bit
0 | EAX=00000000  EBX=00000000  ECX=00000000  EDX=00000300
0 | ESP=00000000  EBP=00000000  ESI=00000000  EDI=00000000
0 | IOPL=0 NV UP DI PL NZ NA PO NC
0 | SEG selector     base    limit G D
0 | SEG sltr(index|ti|rpl)     base    limit G D
0 |  DS:0000( 0000| 0|  0) 00000000 0000ffff 0 0
0 |  ES:0000( 0000| 0|  0) 00000000 0000ffff 0 0
0 |  FS:0000( 0000| 0|  0) 00000000 0000ffff 0 0
0 |  GS:0000( 0000| 0|  0) 00000000 0000ffff 0 0
0 |  SS:0000( 0000| 0|  0) 00000000 0000ffff 0 0
0 |  CS:f000( 0000| 0|  0) 000f0000 0000ffff 0 0
0 | EIP=0000fff0 (0000fff0)
0 >>

--------------------------------------------------------------------------------

Any of you guys have already a workaround to make this works? Tips?
Tricks? 

Thanks for the help,

Rafael (8-)

rafael bmt4 kf TU-Berlin DE
Take a look at our site!
http://privat.schlund.de/bsos/
______________________________

"Unshakable faith is only that
 which can meet reason face to
 face in every Human epoch"

              Allan Kardec
              (1804-1869)
______________________________