[dm-devel] PROBLEM: powertop reports 8000 spurious interrupts/s from USB disk
Marti Raudsepp
marti at juffo.org
Sun May 4 16:24:19 UTC 2008
Hello,
[1.] One line summary of the problem:
PROBLEM: powertop reports 8000 spurious interrupts/s from USB disk
[2.] Full description of the problem/report:
I am frequently seeing bursts of (exactly) 8000 interrupts per second
from my USB controller; it seems to be closely related to activity on
my USB hard disk, although the relation is somewhat vague.
I have been experiencing this problem for a while now, but I have not
bothered to report it until now. It does not seem to cause any visible
performance difference, but it probably stops the CPU from going into
deeper sleep states and is otherwise wasteful.
The effect is painfully visible from powertop as well as dstat. As
seen in lspci output later, I have two EHCI USB controllers: one
integrated nVidia CK804 chipset controller (usb3), and another Via
"VT82xxxxx" PCI controller (usb2); the problem is reproducible with
_both_ of these, and powertop accounts interrupt counts to the
controller where the disk is attached to.
The disk contains one large LVM volume, which stores a typical ext3 file system.
Here is the powertop output from one of these events:
P-states (frequencies)
1.80 Ghz 0.0%
1000 Mhz 100.0%
< Detailed C-state information is only available on Mobile CPUs (laptops) >
Wakeups-from-idle per second : 8420.1 interval: 10.0s
no ACPI power usage estimate available
Top causes for wakeups:
95.4% (7998.7) <interrupt> : ehci_hcd:usb2
2.2% (186.4) <interrupt> : ohci_hcd:usb3, eth0
1.2% (101.9) java : futex_wait (hrtimer_wakeup)
0.3% ( 23.0) USB device 3-1 : USB-PS/2 Optical Mouse (Logitech)
0.2% ( 19.9) wrapper-linux-x : do_nanosleep (hrtimer_wakeup)
0.1% ( 11.3) firefox-bin : futex_wait (hrtimer_wakeup)
0.1% ( 9.1) java : schedule_timeout (process_timeout)
0.1% ( 6.3) <interrupt> : sata_nv, NVidia CK804
Typical burst as seen in dstat (view in monospace font):
----total-cpu-usage---- -dsk/total- -net/total- ---paging-- ---system--
usr sys idl wai hiq siq|_read _writ|_recv _send|__in_ _out_|_int_ _csw_
8 1 90 0 0 1| 0 104k| 76k 19k| 0 0 | 202 730
10 3 87 0 0 0| 0 96k| 92k 17k| 0 0 | 235 907
14 3 75 8 0 0| 48k 0 | 37k 15k| 0 0 |4026 999
<-- running ls -l
12 2 85 0 0 1| 0 0 | 49k 36k| 0 0 |8189 881
9 3 88 0 0 0| 0 0 | 104k 31k| 0 0 |8215 788
10 3 87 0 0 0| 0 48k| 31k 25k| 0 0 |8183 767
9 1 90 0 0 0| 0 0 | 16k 30k| 0 0 |8171 791
8 3 89 0 0 0| 0 304k| 17k 29k| 0 0 |8174 839
5 4 90 0 0 1| 0 0 | 16k 25k| 0 0 |8167 733
7 2 91 0 0 0| 0 0 | 11k 17k| 0 0 |8124 579
7 2 89 2 0 0|8192B 8192B| 16k 12k| 0 0 |4147 768
<-- unmount
11 1 88 0 0 0| 0 0 | 20k 19k| 0 0 | 152 634
8 6 86 0 0 0| 0 568k| 91k 24k| 0 0 | 276 1087
7 4 89 0 0 0| 0 0 | 17k 15k| 0 0 | 205 766
9 3 88 0 0 0| 0 0 | 16k 13k| 0 0 | 169 703
What is obviously visible from the dstat output is that the ~8000
interrupts keep arriving even when there is no actual activity on the
disk, and it also causes no noticeable CPU load.
[3.] Keywords (i.e., modules, networking, kernel):
USB storage, powertop, spurious interrupts, LVM
[4.] Kernel information
[4.1.] Kernel version (from /proc/version):
Linux version 2.6.25-gentoo-r1 (root at non) (gcc version 4.1.2 (Gentoo
4.1.2)) #2 Sun May 4 15:31:09 EEST 2008
[4.2.] Kernel .config file:
http://pastebin.ca/1007100 (set to expire in 3 months)
Note that I used to have the "experimental" CONFIG_USB_SUSPEND option
disabled in kernel versions 2.6.24 and earlier.
[5.] Most recent kernel version which did not have the bug:
I am pretty sure this symptom dates back to 2.6.18, but I probably
just didn't notice it before that. In any case it is not a recent
regression.
[7.] This is how I can typically trigger the situation:
# activate LVM volume group
vgchange -a y portable
# sometimes mount already triggers the event:
mount /dev/portable/media /mnt/media -t ext3 -o noauto,noatime,nosuid
# if mount did not trigger it, listing a long directory typically helps:
ls -la /mnt/media/music
# this often (but not always) stops the interrupt flood
umount /mnt/media
# if the prior did not work, this always seems to work:
vgchange -a n portable
[8.] Environment
[8.1.] Software (add the output of the ver_linux script here)
Linux non 2.6.25-gentoo-r1 #2 Sun May 4 15:31:09 EEST 2008 x86_64 AMD
Athlon(tm) 64 Processor 3000+ AuthenticAMD GNU/Linux
Gnu C 4.1.2
Gnu make 3.81
binutils 2.18
util-linux 2.12r
mount 2.12r
module-init-tools 3.4
e2fsprogs 1.40.4
reiserfsprogs 3.6.19
reiser4progs 1.0.6
xfsprogs 2.8.11
PPP 2.4.4
Linux C Library 2.7
Dynamic linker (ldd) 2.7
Procps 3.2.7
Net-tools 1.60
Kbd 1.13
oprofile 0.9.3
Sh-utils 6.9
udev 118
Modules Loaded pppoe pppox ppp_generic slhc it87 hwmon_vid
eeprom k8temp usbhid i2c_nforce2
[8.2.] Processor information (from /proc/cpuinfo):
processor : 0
vendor_id : AuthenticAMD
cpu family : 15
model : 47
model name : AMD Athlon(tm) 64 Processor 3000+
stepping : 0
cpu MHz : 1000.000
cache size : 512 KB
fpu : yes
fpu_exception : yes
cpuid level : 1
wp : yes
flags : fpu vme de pse tsc msr pae mce cx8 apic sep mtrr pge mca cmov
pat pse36 clflush mmx fxsr sse sse2 syscall nx mmxext fxsr_opt lm
3dnowext 3dnow rep_good pni lahf_lm
bogomips : 2011.89
TLB size : 1024 4K pages
clflush size : 64
cache_alignment : 64
address sizes : 40 bits physical, 48 bits virtual
power management: ts fid vid ttp tm stc
[8.3.] Module information (from /proc/modules):
pppoe 11136 2 - Live 0xffffffff88027000
pppox 3416 1 pppoe, Live 0xffffffff88025000
ppp_generic 20448 6 pppoe,pppox, Live 0xffffffff8801f000
slhc 6144 1 ppp_generic, Live 0xffffffff8801c000
it87 26264 0 - Live 0xffffffff88014000
hwmon_vid 3520 1 it87, Live 0xffffffff88012000
eeprom 6736 0 - Live 0xffffffff8800f000
k8temp 5184 0 - Live 0xffffffff8800c000
usbhid 29920 0 - Live 0xffffffff88003000
i2c_nforce2 6528 0 - Live 0xffffffff88000000
[8.4.] Loaded driver and hardware information (/proc/ioports, /proc/iomem)
# cat /proc/ioports
0000-001f : dma1
0020-0021 : pic1
0040-0043 : timer0
0050-0053 : timer1
0060-006f : keyboard
0070-0077 : rtc
0080-008f : dma page reg
00a0-00a1 : pic2
00c0-00df : dma2
00f0-00ff : fpu
0170-0177 : 0000:00:06.0
0170-0177 : pata_amd
01f0-01f7 : 0000:00:06.0
01f0-01f7 : pata_amd
0290-0297 : pnp 00:02
0295-0296 : it87
0295-0296 : it87
0376-0376 : 0000:00:06.0
0376-0376 : pata_amd
03c0-03df : vga+
03f6-03f6 : 0000:00:06.0
03f6-03f6 : pata_amd
03f8-03ff : serial
04d0-04d1 : pnp 00:02
0800-087f : pnp 00:02
0960-0967 : 0000:00:08.0
0960-0967 : sata_nv
0970-0977 : 0000:00:07.0
0970-0977 : sata_nv
09e0-09e7 : 0000:00:08.0
09e0-09e7 : sata_nv
09f0-09f7 : 0000:00:07.0
09f0-09f7 : sata_nv
0b60-0b63 : 0000:00:08.0
0b60-0b63 : sata_nv
0b70-0b73 : 0000:00:07.0
0b70-0b73 : sata_nv
0be0-0be3 : 0000:00:08.0
0be0-0be3 : sata_nv
0bf0-0bf3 : 0000:00:07.0
0bf0-0bf3 : sata_nv
0cf8-0cff : PCI conf1
4000-407f : pnp 00:01
4000-4003 : ACPI PM1a_EVT_BLK
4004-4005 : ACPI PM1a_CNT_BLK
4008-400b : ACPI PM_TMR
401c-401c : ACPI PM2_CNT_BLK
4020-4027 : ACPI GPE0_BLK
4080-40ff : pnp 00:01
4400-447f : pnp 00:01
4480-44ff : pnp 00:01
44a0-44af : ACPI GPE1_BLK
4800-487f : pnp 00:01
4880-48ff : pnp 00:01
4c00-4c3f : 0000:00:01.1
4c00-4c3f : nForce2_smbus
4c40-4c7f : 0000:00:01.1
4c40-4c7f : nForce2_smbus
a000-afff : PCI Bus #05
a000-a01f : 0000:05:06.0
a000-a01f : uhci_hcd
a400-a41f : 0000:05:06.1
a400-a41f : uhci_hcd
b000-b007 : 0000:00:0a.0
b000-b007 : forcedeth
c400-c40f : 0000:00:08.0
c400-c40f : sata_nv
d800-d80f : 0000:00:07.0
d800-d80f : sata_nv
dc00-dcff : 0000:00:04.0
dc00-dcff : NVidia CK804
e000-e0ff : 0000:00:04.0
e000-e0ff : NVidia CK804
e400-e41f : 0000:00:01.1
f000-f00f : 0000:00:06.0
f000-f00f : pata_amd
# cat /proc/iomem
00000000-0009f7ff : System RAM
0009f800-0009ffff : reserved
000f0000-000fffff : reserved
00100000-7ffeffff : System RAM
01000000-013e653c : Kernel code
013e653d-015c2867 : Kernel data
01614000-0167c927 : Kernel bss
7fff0000-7fff2fff : ACPI Non-volatile Storage
7fff3000-7fffffff : ACPI Tables
c0000000-cfffffff : PCI Bus #01
c0000000-cfffffff : 0000:01:00.0
d0000000-d2ffffff : PCI Bus #01
d0000000-d0ffffff : 0000:01:00.0
d1000000-d1ffffff : 0000:01:00.0
d2000000-d201ffff : 0000:01:00.0
d3000000-d30fffff : PCI Bus #05
d3000000-d30000ff : 0000:05:06.2
d3000000-d30000ff : ehci_hcd
d3100000-d3100fff : 0000:00:0a.0
d3100000-d3100fff : forcedeth
d3101000-d3101fff : 0000:00:08.0
d3101000-d3101fff : sata_nv
d3102000-d3102fff : 0000:00:07.0
d3102000-d3102fff : sata_nv
d3103000-d3103fff : 0000:00:04.0
d3103000-d3103fff : NVidia CK804
d3104000-d3104fff : 0000:00:02.0
d3104000-d3104fff : ohci_hcd
e0000000-efffffff : PCI MMCONFIG 0
e0000000-efffffff : reserved
feb00000-feb000ff : 0000:00:02.1
feb00000-feb000ff : ehci_hcd
fec00000-fec00fff : IOAPIC 0
fec00000-fec00fff : pnp 00:0d
fee00000-fee00fff : Local APIC
fefff000-feffffff : pnp 00:0d
fff80000-fff80fff : pnp 00:0d
fff90000-fffbffff : pnp 00:0d
fffed000-fffeffff : pnp 00:0d
ffff0000-ffffffff : pnp 00:0d
[8.5a.] USB information
# lsusb
Bus 005 Device 001: ID 1d6b:0001
Bus 004 Device 001: ID 1d6b:0001
Bus 003 Device 003: ID 046d:c043 Logitech, Inc.
Bus 003 Device 002: ID 03f0:1024 Hewlett-Packard
Bus 003 Device 001: ID 1d6b:0001
Bus 002 Device 002: ID 1058:0701 Western Digital Technologies, Inc.
Bus 002 Device 001: ID 1d6b:0002
Bus 001 Device 001: ID 1d6b:0002
# lsusb -vd 1058:0701
Bus 002 Device 002: ID 1058:0701 Western Digital Technologies, Inc.
Device Descriptor:
bLength 18
bDescriptorType 1
bcdUSB 2.00
bDeviceClass 0 (Defined at Interface level)
bDeviceSubClass 0
bDeviceProtocol 0
bMaxPacketSize0 64
idVendor 0x1058 Western Digital Technologies, Inc.
idProduct 0x0701
bcdDevice 2.40
iManufacturer 89 Western Digital
iProduct 76 External HDD
iSerial 63 DEF10CD7F64C
bNumConfigurations 1
Configuration Descriptor:
bLength 9
bDescriptorType 2
wTotalLength 39
bNumInterfaces 1
bConfigurationValue 1
iConfiguration 105 USB 2.0
bmAttributes 0xc0
Self Powered
MaxPower 2mA
Interface Descriptor:
bLength 9
bDescriptorType 4
bInterfaceNumber 0
bAlternateSetting 0
bNumEndpoints 3
bInterfaceClass 8 Mass Storage
bInterfaceSubClass 6 SCSI
bInterfaceProtocol 80 Bulk (Zip)
iInterface 0
Endpoint Descriptor:
bLength 7
bDescriptorType 5
bEndpointAddress 0x02 EP 2 OUT
bmAttributes 2
Transfer Type Bulk
Synch Type None
Usage Type Data
wMaxPacketSize 0x0200 1x 512 bytes
bInterval 0
Endpoint Descriptor:
bLength 7
bDescriptorType 5
bEndpointAddress 0x86 EP 6 IN
bmAttributes 2
Transfer Type Bulk
Synch Type None
Usage Type Data
wMaxPacketSize 0x0200 1x 512 bytes
bInterval 0
Endpoint Descriptor:
bLength 7
bDescriptorType 5
bEndpointAddress 0x81 EP 1 IN
bmAttributes 3
Transfer Type Interrupt
Synch Type None
Usage Type Data
wMaxPacketSize 0x0002 1x 2 bytes
bInterval 12
Device Qualifier (for other device speed):
bLength 10
bDescriptorType 6
bcdUSB 2.00
bDeviceClass 0 (Defined at Interface level)
bDeviceSubClass 0
bDeviceProtocol 0
bMaxPacketSize0 64
bNumConfigurations 1
Device Status: 0x0001
Self Powered
[8.5b.] PCI information ('lspci -vvv' as root)
00:00.0 Memory controller: nVidia Corporation CK804 Memory Controller (rev a3)
Subsystem: ASUSTeK Computer Inc. A8N-E Mainboard
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort-
<TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
Capabilities: [44] HyperTransport: Slave or Primary Interface
Command: BaseUnitID=0 UnitCnt=15 MastHost- DefDir- DUL-
Link Control 0: CFlE+ CST- CFE- <LkFail- Init+ EOC- TXO- <CRCErr=0
IsocEn- LSEn- ExtCTL- 64b-
Link Config 0: MLWI=16bit DwFcIn- MLWO=16bit DwFcOut- LWI=16bit
DwFcInEn- LWO=16bit DwFcOutEn-
Link Control 1: CFlE- CST- CFE- <LkFail+ Init- EOC+ TXO+ <CRCErr=0
IsocEn- LSEn- ExtCTL- 64b-
Link Config 1: MLWI=8bit DwFcIn- MLWO=8bit DwFcOut- LWI=8bit
DwFcInEn- LWO=8bit DwFcOutEn-
Revision ID: 1.03
Link Frequency 0: 1.0GHz
Link Error 0: <Prot- <Ovfl- <EOC- CTLTm-
Link Frequency Capability 0: 200MHz+ 300MHz+ 400MHz+ 500MHz+ 600MHz+
800MHz+ 1.0GHz+ 1.2GHz- 1.4GHz- 1.6GHz- Vend-
Feature Capability: IsocFC+ LDTSTOP+ CRCTM- ECTLT- 64bA- UIDRD-
Link Frequency 1: 200MHz
Link Error 1: <Prot- <Ovfl- <EOC- CTLTm-
Link Frequency Capability 1: 200MHz- 300MHz- 400MHz- 500MHz- 600MHz-
800MHz- 1.0GHz- 1.2GHz- 1.4GHz- 1.6GHz- Vend-
Error Handling: PFlE+ OFlE+ PFE- OFE- EOCFE- RFE- CRCFE- SERRFE- CF-
RE- PNFE- ONFE- EOCNFE- RNFE- CRCNFE- SERRNFE-
Prefetchable memory behind bridge Upper: 00-00
Bus Number: 00
Capabilities: [e0] HyperTransport: MSI Mapping Enable+ Fixed-
Mapping Address Base: 00000000fee00000
00:01.0 ISA bridge: nVidia Corporation CK804 ISA Bridge (rev a3)
Subsystem: ASUSTeK Computer Inc. K8N4-E or A8N-E Mainboard
Control: I/O+ Mem+ BusMaster+ SpecCycle+ MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx-
Status: Cap- 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort-
<TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
00:01.1 SMBus: nVidia Corporation CK804 SMBus (rev a2)
Subsystem: ASUSTeK Computer Inc. K8N4-E or A8N-E Mainboard
Control: I/O+ Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort-
<TAbort- <MAbort- >SERR- <PERR- INTx-
Interrupt: pin A routed to IRQ 255
Region 0: I/O ports at e400 [size=32]
Region 4: I/O ports at 4c00 [size=64]
Region 5: I/O ports at 4c40 [size=64]
Capabilities: [44] Power Management version 2
Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot+,D3cold+)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
Kernel driver in use: nForce2_smbus
Kernel modules: i2c-nforce2
00:02.0 USB Controller: nVidia Corporation CK804 USB Controller (rev
a2) (prog-if 10 [OHCI])
Subsystem: ASUSTeK Computer Inc. K8N4-E or A8N-E Mainboard
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort-
<TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0 (750ns min, 250ns max)
Interrupt: pin A routed to IRQ 23
Region 0: Memory at d3104000 (32-bit, non-prefetchable) [size=4K]
Capabilities: [44] Power Management version 2
Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=0mA PME(D0+,D1+,D2+,D3hot+,D3cold+)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
Kernel driver in use: ohci_hcd
00:02.1 USB Controller: nVidia Corporation CK804 USB Controller (rev
a3) (prog-if 20 [EHCI])
Subsystem: ASUSTeK Computer Inc. K8N4-E or A8N-E Mainboard
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort-
<TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0 (750ns min, 250ns max)
Interrupt: pin B routed to IRQ 20
Region 0: Memory at feb00000 (32-bit, non-prefetchable) [size=256]
Capabilities: [44] Debug port: BAR=1 offset=0098
Capabilities: [80] Power Management version 2
Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=0mA PME(D0+,D1+,D2+,D3hot+,D3cold+)
Status: D0 PME-Enable- DSel=0 DScale=0 PME+
Kernel driver in use: ehci_hcd
00:04.0 Multimedia audio controller: nVidia Corporation CK804 AC'97
Audio Controller (rev a2)
Subsystem: ASUSTeK Computer Inc. K8N4-E or A8N-E Mainboard
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort-
<TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0 (500ns min, 1250ns max)
Interrupt: pin A routed to IRQ 22
Region 0: I/O ports at dc00 [size=256]
Region 1: I/O ports at e000 [size=256]
Region 2: Memory at d3103000 (32-bit, non-prefetchable) [size=4K]
Capabilities: [44] Power Management version 2
Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
Kernel driver in use: Intel ICH
00:06.0 IDE interface: nVidia Corporation CK804 IDE (rev f2) (prog-if
8a [Master SecP PriP])
Subsystem: Unknown device f043:815a
Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort-
<TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0 (750ns min, 250ns max)
Region 0: [virtual] Memory at 000001f0 (32-bit, non-prefetchable)
[disabled] [size=8]
Region 1: [virtual] Memory at 000003f0 (type 3, non-prefetchable)
[disabled] [size=1]
Region 2: [virtual] Memory at 00000170 (32-bit, non-prefetchable)
[disabled] [size=8]
Region 3: [virtual] Memory at 00000370 (type 3, non-prefetchable)
[disabled] [size=1]
Region 4: I/O ports at f000 [size=16]
Capabilities: [44] Power Management version 2
Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
Kernel driver in use: pata_amd
00:07.0 IDE interface: nVidia Corporation CK804 Serial ATA Controller
(rev f3) (prog-if 85 [Master SecO PriO])
Subsystem: ASUSTeK Computer Inc. A8N-E Mainboard
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort-
<TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0 (750ns min, 250ns max)
Interrupt: pin A routed to IRQ 22
Region 0: I/O ports at 09f0 [size=8]
Region 1: I/O ports at 0bf0 [size=4]
Region 2: I/O ports at 0970 [size=8]
Region 3: I/O ports at 0b70 [size=4]
Region 4: I/O ports at d800 [size=16]
Region 5: Memory at d3102000 (32-bit, non-prefetchable) [size=4K]
Capabilities: [44] Power Management version 2
Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
Kernel driver in use: sata_nv
00:08.0 IDE interface: nVidia Corporation CK804 Serial ATA Controller
(rev f3) (prog-if 85 [Master SecO PriO])
Subsystem: ASUSTeK Computer Inc. K8N4-E or A8N-E Mainboard
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort-
<TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0 (750ns min, 250ns max)
Interrupt: pin A routed to IRQ 21
Region 0: I/O ports at 09e0 [size=8]
Region 1: I/O ports at 0be0 [size=4]
Region 2: I/O ports at 0960 [size=8]
Region 3: I/O ports at 0b60 [size=4]
Region 4: I/O ports at c400 [size=16]
Region 5: Memory at d3101000 (32-bit, non-prefetchable) [size=4K]
Capabilities: [44] Power Management version 2
Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
Kernel driver in use: sata_nv
00:09.0 PCI bridge: nVidia Corporation CK804 PCI Bridge (rev a2)
(prog-if 01 [Subtractive decode])
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR+ FastB2B- DisINTx-
Status: Cap- 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort-
<TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
Bus: primary=00, secondary=05, subordinate=05, sec-latency=128
I/O behind bridge: 0000a000-0000afff
Memory behind bridge: d3000000-d30fffff
Prefetchable memory behind bridge: fff00000-000fffff
Secondary status: 66MHz- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort+ <SERR- <PERR+
BridgeCtl: Parity- SERR+ NoISA- VGA- MAbort- >Reset- FastB2B-
PriDiscTmr- SecDiscTmr+ DiscTmrStat- DiscTmrSERREn-
00:0a.0 Bridge: nVidia Corporation CK804 Ethernet Controller (rev a3)
Subsystem: ASUSTeK Computer Inc. K8N4-E or A8N-E Mainboard
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort-
<TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0 (250ns min, 5000ns max)
Interrupt: pin A routed to IRQ 23
Region 0: Memory at d3100000 (32-bit, non-prefetchable) [size=4K]
Region 1: I/O ports at b000 [size=8]
Capabilities: [44] Power Management version 2
Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=0mA PME(D0+,D1+,D2+,D3hot+,D3cold+)
Status: D0 PME-Enable+ DSel=0 DScale=0 PME-
Kernel driver in use: forcedeth
00:0b.0 PCI bridge: nVidia Corporation CK804 PCIE Bridge (rev a3)
(prog-if 00 [Normal decode])
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR+ FastB2B- DisINTx+
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort-
<TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0, Cache Line Size: 32 bytes
Bus: primary=00, secondary=04, subordinate=04, sec-latency=0
I/O behind bridge: 0000f000-00000fff
Memory behind bridge: fff00000-000fffff
Prefetchable memory behind bridge: 00000000fff00000-00000000000fffff
Secondary status: 66MHz- FastB2B- ParErr- DEVSEL=fast >TAbort-
<TAbort- <MAbort- <SERR- <PERR-
BridgeCtl: Parity- SERR+ NoISA- VGA- MAbort- >Reset- FastB2B-
PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn-
Capabilities: [40] Power Management version 2
Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0+,D1+,D2+,D3hot+,D3cold+)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
Capabilities: [48] Message Signalled Interrupts: Mask- 64bit+ Queue=0/1 Enable+
Address: 00000000fee0100c Data: 4149
Capabilities: [58] HyperTransport: MSI Mapping Enable+ Fixed-
Mapping Address Base: 00000000fee00000
Capabilities: [80] Express (v1) Root Port (Slot+), MSI 00
DevCap: MaxPayload 128 bytes, PhantFunc 0, Latency L0s <512ns, L1 <4us
ExtTag- RBE- FLReset-
DevCtl: Report errors: Correctable+ Non-Fatal+ Fatal+ Unsupported+
RlxdOrd+ ExtTag- PhantFunc- AuxPwr- NoSnoop+
MaxPayload 128 bytes, MaxReadReq 512 bytes
DevSta: CorrErr- UncorrErr- FatalErr- UnsuppReq- AuxPwr- TransPend-
LnkCap: Port #3, Speed 2.5GT/s, Width x2, ASPM L0s, Latency L0 <512ns, L1 <4us
ClockPM- Suprise- LLActRep- BwNot-
LnkCtl: ASPM Disabled; RCB 64 bytes Disabled- Retrain- CommClk-
ExtSynch- ClockPM- AutWidDis- BWInt- AutBWInt-
LnkSta: Speed 2.5GT/s, Width x4, TrErr- Train- SlotClk+ DLActive-
BWMgmt- ABWMgmt-
SltCap: AttnBtn- PwrCtrl- MRL- AttnInd- PwrInd- HotPlug- Surpise-
Slot # 8, PowerLimit 25.000000; Interlock- NoCompl-
SltCtl: Enable: AttnBtn- PwrFlt- MRL- PresDet- CmdCplt- HPIrq- LinkChg-
Control: AttnInd Off, PwrInd On, Power- Interlock-
SltSta: Status: AttnBtn- PowerFlt- MRL- CmdCplt- PresDet+ Interlock-
Changed: MRL- PresDet- LinkState-
RootCtl: ErrCorrectable- ErrNon-Fatal- ErrFatal- PMEIntEna- CRSVisible-
RootCap: CRSVisible-
RootSta: PME ReqID 0000, PMEStatus- PMEPending-
Capabilities: [100] Virtual Channel <?>
Kernel driver in use: pcieport-driver
00:0c.0 PCI bridge: nVidia Corporation CK804 PCIE Bridge (rev a3)
(prog-if 00 [Normal decode])
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR+ FastB2B- DisINTx+
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort-
<TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0, Cache Line Size: 32 bytes
Bus: primary=00, secondary=03, subordinate=03, sec-latency=0
I/O behind bridge: 0000f000-00000fff
Memory behind bridge: fff00000-000fffff
Prefetchable memory behind bridge: 00000000fff00000-00000000000fffff
Secondary status: 66MHz- FastB2B- ParErr- DEVSEL=fast >TAbort-
<TAbort- <MAbort- <SERR- <PERR-
BridgeCtl: Parity- SERR+ NoISA- VGA- MAbort- >Reset- FastB2B-
PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn-
Capabilities: [40] Power Management version 2
Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0+,D1+,D2+,D3hot+,D3cold+)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
Capabilities: [48] Message Signalled Interrupts: Mask- 64bit+ Queue=0/1 Enable+
Address: 00000000fee0100c Data: 4151
Capabilities: [58] HyperTransport: MSI Mapping Enable+ Fixed-
Mapping Address Base: 00000000fee00000
Capabilities: [80] Express (v1) Root Port (Slot+), MSI 00
DevCap: MaxPayload 128 bytes, PhantFunc 0, Latency L0s <512ns, L1 <4us
ExtTag- RBE- FLReset-
DevCtl: Report errors: Correctable+ Non-Fatal+ Fatal+ Unsupported+
RlxdOrd+ ExtTag- PhantFunc- AuxPwr- NoSnoop+
MaxPayload 128 bytes, MaxReadReq 512 bytes
DevSta: CorrErr- UncorrErr- FatalErr- UnsuppReq- AuxPwr- TransPend-
LnkCap: Port #2, Speed 2.5GT/s, Width x1, ASPM L0s, Latency L0 <512ns, L1 <4us
ClockPM- Suprise- LLActRep- BwNot-
LnkCtl: ASPM Disabled; RCB 64 bytes Disabled- Retrain- CommClk-
ExtSynch- ClockPM- AutWidDis- BWInt- AutBWInt-
LnkSta: Speed 2.5GT/s, Width x4, TrErr- Train- SlotClk+ DLActive-
BWMgmt- ABWMgmt-
SltCap: AttnBtn- PwrCtrl- MRL- AttnInd- PwrInd- HotPlug- Surpise-
Slot # 4, PowerLimit 10.000000; Interlock- NoCompl-
SltCtl: Enable: AttnBtn- PwrFlt- MRL- PresDet- CmdCplt- HPIrq- LinkChg-
Control: AttnInd Off, PwrInd On, Power- Interlock-
SltSta: Status: AttnBtn- PowerFlt- MRL- CmdCplt- PresDet- Interlock-
Changed: MRL- PresDet- LinkState-
RootCtl: ErrCorrectable- ErrNon-Fatal- ErrFatal- PMEIntEna- CRSVisible-
RootCap: CRSVisible-
RootSta: PME ReqID 0000, PMEStatus- PMEPending-
Capabilities: [100] Virtual Channel <?>
Kernel driver in use: pcieport-driver
00:0d.0 PCI bridge: nVidia Corporation CK804 PCIE Bridge (rev a3)
(prog-if 00 [Normal decode])
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR+ FastB2B- DisINTx+
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort-
<TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0, Cache Line Size: 32 bytes
Bus: primary=00, secondary=02, subordinate=02, sec-latency=0
I/O behind bridge: 0000f000-00000fff
Memory behind bridge: fff00000-000fffff
Prefetchable memory behind bridge: 00000000fff00000-00000000000fffff
Secondary status: 66MHz- FastB2B- ParErr- DEVSEL=fast >TAbort-
<TAbort- <MAbort- <SERR- <PERR-
BridgeCtl: Parity- SERR+ NoISA- VGA- MAbort- >Reset- FastB2B-
PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn-
Capabilities: [40] Power Management version 2
Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0+,D1+,D2+,D3hot+,D3cold+)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
Capabilities: [48] Message Signalled Interrupts: Mask- 64bit+ Queue=0/1 Enable+
Address: 00000000fee0100c Data: 4159
Capabilities: [58] HyperTransport: MSI Mapping Enable+ Fixed-
Mapping Address Base: 00000000fee00000
Capabilities: [80] Express (v1) Root Port (Slot+), MSI 00
DevCap: MaxPayload 128 bytes, PhantFunc 0, Latency L0s <512ns, L1 <4us
ExtTag- RBE- FLReset-
DevCtl: Report errors: Correctable+ Non-Fatal+ Fatal+ Unsupported+
RlxdOrd+ ExtTag- PhantFunc- AuxPwr- NoSnoop+
MaxPayload 128 bytes, MaxReadReq 512 bytes
DevSta: CorrErr- UncorrErr- FatalErr- UnsuppReq- AuxPwr- TransPend-
LnkCap: Port #1, Speed 2.5GT/s, Width x1, ASPM L0s, Latency L0 <512ns, L1 <4us
ClockPM- Suprise- LLActRep- BwNot-
LnkCtl: ASPM Disabled; RCB 64 bytes Disabled- Retrain- CommClk-
ExtSynch- ClockPM- AutWidDis- BWInt- AutBWInt-
LnkSta: Speed 2.5GT/s, Width x8, TrErr- Train- SlotClk+ DLActive-
BWMgmt- ABWMgmt-
SltCap: AttnBtn- PwrCtrl- MRL- AttnInd- PwrInd- HotPlug- Surpise-
Slot # 2, PowerLimit 10.000000; Interlock- NoCompl-
SltCtl: Enable: AttnBtn- PwrFlt- MRL- PresDet- CmdCplt- HPIrq- LinkChg-
Control: AttnInd Off, PwrInd On, Power- Interlock-
SltSta: Status: AttnBtn- PowerFlt- MRL- CmdCplt- PresDet- Interlock-
Changed: MRL- PresDet- LinkState-
RootCtl: ErrCorrectable- ErrNon-Fatal- ErrFatal- PMEIntEna- CRSVisible-
RootCap: CRSVisible-
RootSta: PME ReqID 0000, PMEStatus- PMEPending-
Capabilities: [100] Virtual Channel <?>
Kernel driver in use: pcieport-driver
00:0e.0 PCI bridge: nVidia Corporation CK804 PCIE Bridge (rev a3)
(prog-if 00 [Normal decode])
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR+ FastB2B- DisINTx+
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort-
<TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0, Cache Line Size: 32 bytes
Bus: primary=00, secondary=01, subordinate=01, sec-latency=0
I/O behind bridge: 0000f000-00000fff
Memory behind bridge: d0000000-d2ffffff
Prefetchable memory behind bridge: 00000000c0000000-00000000cfffffff
Secondary status: 66MHz- FastB2B- ParErr- DEVSEL=fast >TAbort-
<TAbort- <MAbort+ <SERR- <PERR-
BridgeCtl: Parity- SERR+ NoISA- VGA+ MAbort- >Reset- FastB2B-
PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn-
Capabilities: [40] Power Management version 2
Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0+,D1+,D2+,D3hot+,D3cold+)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
Capabilities: [48] Message Signalled Interrupts: Mask- 64bit+ Queue=0/1 Enable+
Address: 00000000fee0100c Data: 4161
Capabilities: [58] HyperTransport: MSI Mapping Enable+ Fixed-
Mapping Address Base: 00000000fee00000
Capabilities: [80] Express (v1) Root Port (Slot+), MSI 00
DevCap: MaxPayload 128 bytes, PhantFunc 0, Latency L0s <512ns, L1 <4us
ExtTag- RBE- FLReset-
DevCtl: Report errors: Correctable+ Non-Fatal+ Fatal+ Unsupported+
RlxdOrd+ ExtTag- PhantFunc- AuxPwr- NoSnoop+
MaxPayload 128 bytes, MaxReadReq 512 bytes
DevSta: CorrErr+ UncorrErr- FatalErr+ UnsuppReq- AuxPwr- TransPend-
LnkCap: Port #0, Speed 2.5GT/s, Width x16, ASPM L0s, Latency L0
<512ns, L1 <4us
ClockPM- Suprise- LLActRep- BwNot-
LnkCtl: ASPM Disabled; RCB 64 bytes Disabled- Retrain- CommClk-
ExtSynch- ClockPM- AutWidDis- BWInt- AutBWInt-
LnkSta: Speed 2.5GT/s, Width x16, TrErr- Train- SlotClk+ DLActive-
BWMgmt- ABWMgmt-
SltCap: AttnBtn- PwrCtrl- MRL- AttnInd- PwrInd- HotPlug- Surpise-
Slot # 1, PowerLimit 75.000000; Interlock- NoCompl-
SltCtl: Enable: AttnBtn- PwrFlt- MRL- PresDet- CmdCplt- HPIrq- LinkChg-
Control: AttnInd Off, PwrInd On, Power- Interlock-
SltSta: Status: AttnBtn- PowerFlt- MRL- CmdCplt- PresDet+ Interlock-
Changed: MRL- PresDet- LinkState-
RootCtl: ErrCorrectable- ErrNon-Fatal- ErrFatal- PMEIntEna- CRSVisible-
RootCap: CRSVisible-
RootSta: PME ReqID 0000, PMEStatus- PMEPending-
Capabilities: [100] Virtual Channel <?>
Kernel driver in use: pcieport-driver
00:18.0 Host bridge: Advanced Micro Devices [AMD] K8
[Athlon64/Opteron] HyperTransport Technology Configuration
Control: I/O- Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort-
<TAbort- <MAbort- >SERR- <PERR- INTx-
Capabilities: [80] HyperTransport: Host or Secondary Interface
!!! Possibly incomplete decoding
Command: WarmRst+ DblEnd-
Link Control: CFlE- CST- CFE- <LkFail- Init+ EOC- TXO- <CRCErr=0
Link Config: MLWI=16bit MLWO=16bit LWI=16bit LWO=16bit
Revision ID: 1.02
00:18.1 Host bridge: Advanced Micro Devices [AMD] K8
[Athlon64/Opteron] Address Map
Control: I/O- Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx-
Status: Cap- 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort-
<TAbort- <MAbort- >SERR- <PERR- INTx-
00:18.2 Host bridge: Advanced Micro Devices [AMD] K8
[Athlon64/Opteron] DRAM Controller
Control: I/O- Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx-
Status: Cap- 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort-
<TAbort- <MAbort- >SERR- <PERR- INTx-
00:18.3 Host bridge: Advanced Micro Devices [AMD] K8
[Athlon64/Opteron] Miscellaneous Control
Control: I/O- Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx-
Status: Cap- 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort-
<TAbort- <MAbort- >SERR- <PERR- INTx-
Kernel driver in use: k8temp
Kernel modules: k8temp
01:00.0 VGA compatible controller: nVidia Corporation NV44 [GeForce
6200 TurboCache(TM)] (rev a1) (prog-if 00 [VGA controller])
Subsystem: Micro-Star International Co., Ltd. Unknown device 0271
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort-
<TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0, Cache Line Size: 32 bytes
Interrupt: pin A routed to IRQ 3
Region 0: Memory at d0000000 (32-bit, non-prefetchable) [size=16M]
Region 1: Memory at c0000000 (64-bit, prefetchable) [size=256M]
Region 3: Memory at d1000000 (64-bit, non-prefetchable) [size=16M]
Expansion ROM at d2000000 [disabled] [size=128K]
Capabilities: [60] Power Management version 2
Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
Capabilities: [68] Message Signalled Interrupts: Mask- 64bit+ Queue=0/0 Enable-
Address: 0000000000000000 Data: 0000
Capabilities: [78] Express (v1) Endpoint, MSI 00
DevCap: MaxPayload 128 bytes, PhantFunc 0, Latency L0s <512ns, L1 <4us
ExtTag- AttnBtn- AttnInd- PwrInd- RBE- FLReset-
DevCtl: Report errors: Correctable- Non-Fatal- Fatal- Unsupported-
RlxdOrd+ ExtTag- PhantFunc- AuxPwr- NoSnoop+
MaxPayload 128 bytes, MaxReadReq 512 bytes
DevSta: CorrErr- UncorrErr+ FatalErr- UnsuppReq+ AuxPwr- TransPend-
LnkCap: Port #0, Speed 2.5GT/s, Width x16, ASPM L0s L1, Latency L0
<1us, L1 <4us
ClockPM- Suprise- LLActRep- BwNot-
LnkCtl: ASPM Disabled; RCB 128 bytes Disabled- Retrain- CommClk-
ExtSynch- ClockPM- AutWidDis- BWInt- AutBWInt-
LnkSta: Speed 2.5GT/s, Width x16, TrErr- Train- SlotClk+ DLActive-
BWMgmt- ABWMgmt-
Capabilities: [100] Virtual Channel <?>
Capabilities: [128] Power Budgeting <?>
05:06.0 USB Controller: VIA Technologies, Inc. VT82xxxxx UHCI USB 1.1
Controller (rev 61) (prog-if 00 [UHCI])
Subsystem: VIA Technologies, Inc. VT82xxxxx UHCI USB 1.1 Controller
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 32, Cache Line Size: 32 bytes
Interrupt: pin A routed to IRQ 16
Region 4: I/O ports at a000 [size=32]
Capabilities: [80] Power Management version 2
Flags: PMEClk+ DSI- D1+ D2+ AuxCurrent=0mA PME(D0+,D1+,D2+,D3hot+,D3cold-)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
Kernel driver in use: uhci_hcd
05:06.1 USB Controller: VIA Technologies, Inc. VT82xxxxx UHCI USB 1.1
Controller (rev 61) (prog-if 00 [UHCI])
Subsystem: VIA Technologies, Inc. VT82xxxxx UHCI USB 1.1 Controller
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 32, Cache Line Size: 32 bytes
Interrupt: pin B routed to IRQ 17
Region 4: I/O ports at a400 [size=32]
Capabilities: [80] Power Management version 2
Flags: PMEClk+ DSI- D1+ D2+ AuxCurrent=0mA PME(D0+,D1+,D2+,D3hot+,D3cold-)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
Kernel driver in use: uhci_hcd
05:06.2 USB Controller: VIA Technologies, Inc. USB 2.0 (rev 63)
(prog-if 20 [EHCI])
Subsystem: VIA Technologies, Inc. USB 2.0
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV+ VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 32, Cache Line Size: 64 bytes
Interrupt: pin C routed to IRQ 18
Region 0: Memory at d3000000 (32-bit, non-prefetchable) [size=256]
Capabilities: [80] Power Management version 2
Flags: PMEClk+ DSI- D1+ D2+ AuxCurrent=0mA PME(D0+,D1+,D2+,D3hot+,D3cold-)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
Kernel driver in use: ehci_hcd
Regards,
Marti Raudsepp
More information about the dm-devel
mailing list