Results of On-board NIC...any suggestions?

["Brent W." <brenthel yahoo com>]

results of netstat -ar

Destination    Gateway      Genmask       Flags   MSS
Window    irrt Iface
192.168.0.0       *        255.255.255.0   U      40 0
         0 eth0
127.0.0.0         *         255.0.0.0      U      40 0
         0 lo
default       192.168.0.1    0.0.0.0       UG     40 0
        0 ehto





results of netstat -nr

The same as -ar except The Desination columns end with
0.0.0.0.0 instead of default




rsults of cat network

NETWORKING=yes
HOSTNAME=localhost.localdomain


I am connection directly to the router.  No hub
involved. Recently the light on the router has
remained on.  I changed the setting in the bios to
networking=yes and now the light stays on.


The router is a D-Link DI-614+

i'm only trying to connect to a local machine...for
now.

thanks




--- Keith Mastin <kmastin beechtree ca> wrote:
> >Hi Keith
> >What are the results when you use the 'ifconfig'
> and 'netstat -nr' command?
> >Also if you go to /etc/sysconfig and type 'cat
> network' what are the results
> >of that?
> >
> >Also what are you trying to ping; any host on the
> same segment?
> >
> >What router are you attached to, are you directly
> connected to it or via a
> >hub?
> >
> >Mark
> 
> Hey Mark,
> this is a misconception caused by messed up
> quotes... I was the one who 
> asked the OP for the output of netstat -ar
> :)
> 
> >
> >
> >----- Original Message -----
> >From: "Keith Mastin" <kmastin beechtree ca>
> >To: <enigma-list redhat com>
> >Sent: Wednesday, November 13, 2002 9:30 AM
> >Subject: Re: On-board NIC
> >
> >
> >> >I have my eth0 up and running(ifconfig).  set-up
> ip
> >> >address with netconfig.  when i ping anything
> but lo
> >> >interface(which by the way means nothing) i get
> >> >Destination host unreachable.  my router led is
> not
> >> >showing a connection.
> >> >
> >> >dmesg | grep eth0
> >> >eth0:RealTek RTL8139 Fast Ethernet at
> 0xc284a400,
> >> >00:90:47:00:b5:cv IRQ 15
> >> >eth0:identified RTL8139 chip type 'RTL-8139c'
> >> >eth0: setting 100mbs full-duplexbased on
> >> >auto-negotiated partner ability 41e1
> >> >
> >> >My puter is old. I don't even know what type of
> card
> >> >it is or if it is supported.  Therefore i
> plugged in a
> >> >3com 3c509b card.  Now lo, eth0, and eth1 all up
> on
> >> >ifconfig. Same issues, however the router led
> flickers
> >> >with no apparent pattern.
> >> >
> >> >i have a hardware address and IRQ number.  does
> anyone
> >> >have any suggestions for a newbie?
> >>
> >> Show us the output of netstat -ar
> 
> 
> 
> _______________________________________________
> enigma-list mailing list
> enigma-list redhat com
>
https://listman.redhat.com/mailman/listinfo/enigma-list


__________________________________________________
Do you Yahoo!?
Yahoo! Web Hosting - Let the expert host your site
http://webhosting.yahoo.com