usb-mouse (usb-uhci & usb-ohci) why loads module?
Dirk Wendland
dirk.wendland at nexgo.de
Wed Feb 4 10:14:29 UTC 2004
Hello
Most Converters from example serial to usb and so on have also drivers maybe
the usb-converter is the problem.
Dirk Wendland
Saarland
Germany
http://www.develop.if2.de
A little development Tool for C++ / Java / OpenGL
under Linux
Linux Rules ;)
----- Original Message -----
From: "Roger Grosswiler" <roger at gwch.net>
To: <fedora-list at redhat.com>
Sent: Wednesday, February 04, 2004 9:58 AM
Subject: usb-mouse (usb-uhci & usb-ohci) why loads module?
> hi all,
>
> i am a complete newbie in usb, so i need some help to understand whats
> going on. Sorry for this real huge statement, but i wanted to deliver all
> perhaps needed information @once. Will cut off in replies, what is not
> needed...
>
> ...i have a compaq proliant server, with a pci usb-hub with 2 ports. ...i
> have a old logitech ps/2 mouseman.
> ...i connect this ps/2 mouseman to a usb-converter
> ...i plug it into the usb-port
>
> ...and nothing happens, mouse is not moving. have perhaps to say, that
> between mouse and proliant there is a ps/2 kvm-swich.
>
> nevertheless, my proliant seems to recognize something, because of the
> following errors:
>
> [root at morpheus log]# more messages | grep usb
> Feb 3 18:11:22 morpheus kernel: usb.c: registered new driver usbdevfs Feb
> 3 18:11:22 morpheus kernel: usb.c: registered new driver hub
> Feb 3 18:11:23 morpheus kernel: usb-uhci.c: $Revision: 1.275 $ time
> 13:16:59 Jan 7 2004 --* why??? i got on boot-time several error-messages
> about this module not to be loaded. also compaq uses as i read ohci
> instead
> Feb 3 18:11:23 morpheus kernel: usb-uhci.c: High bandwidth mode enabled
> Feb 3 18:11:23 morpheus kernel: usb-uhci.c: found UHCI device with no IRQ
> assigned. check BIOS settings!
> Feb 3 18:11:23 morpheus kernel: usb-uhci.c: v1.275:USB Universal Host
> Controller Interface driver
> Feb 3 18:11:23 morpheus kernel: usb-ohci.c: USB OHCI at membase
> 0xd0893000, IRQ 5
> Feb 3 18:11:23 morpheus kernel: usb-ohci.c: usb-01:0d.0, OPTi Inc. 82C861
> Feb 3 18:11:23 morpheus kernel: usb.c: new USB bus registered, assigned
> bus number 1
> Feb 3 18:11:23 morpheus kernel: usb.c: registered new driver hiddev Feb
> 3 18:11:23 morpheus kernel: usb.c: registered new driver hid
> Feb 3 18:11:24 morpheus kernel: usb.c: USB device not accepting new
> address=2 (error=-110) --* this is the mouse i think
> Feb 3 18:11:24 morpheus kernel: usb.c: USB device not accepting new
> address=3 (error=-110) --* this is the mouse too, i think...
> Feb 3 18:11:24 morpheus kernel: usb.c: USB device 4 (vend/prod
> 0x3f0/0x1411) is not claimed by any active driver.
> Feb 3 18:11:24 morpheus kernel: usb.c: registered new driver usbscanner
> Feb 3 18:11:24 morpheus kernel: usb.c: registered new driver usblp Feb 3
> 18:11:24 morpheus kernel: printer.c: usblp0: USB Bidirectional printer dev
> 4 if 0 alt 1 proto 2 vid 0x03F0 pid 0x1411
> Feb 3 18:11:26 morpheus kernel: usb-uhci.c: $Revision: 1.275 $ time
> 13:16:59 Jan 7 2004
> Feb 3 18:11:26 morpheus kernel: usb-uhci.c: High bandwidth mode enabled
> Feb 3 18:11:26 morpheus kernel: usb-uhci.c: found UHCI device with no IRQ
> assigned. check BIOS settings!
> Feb 3 18:11:26 morpheus kernel: usb-uhci.c: v1.275:USB Universal Host
> Controller Interface driver
>
> ...and here some more diagnosis...
>
> ----* /sbin/lsmod:
> [root at morpheus log]# /sbin/lsmod
> Module Size Used by Not tainted
> ppdev 7116 0 (autoclean)
> soundcore 6468 0 (autoclean)
> parport_pc 18756 1 (autoclean)
> lp 8580 0 (autoclean)
> parport 37056 1 (autoclean) [ppdev parport_pc lp] autofs
> 12084 0 (autoclean) (unused)
> tlan 32220 1
> floppy 57308 0 (autoclean)
> sg 35436 0 (autoclean)
> sr_mod 17400 0 (autoclean)
> microcode 4188 0 (autoclean)
> ide-scsi 12016 0
> ide-cd 34432 0
> cdrom 34592 0 [sr_mod ide-cd]
> printer 9376 0
> scanner 11544 0
> keybdev 2656 0 (unused)
> hid 23908 0 (unused)
> usb-ohci 21544 0 (unused)
> usbcore 78752 1 [printer scanner hid usb-ohci]
> mousedev 5268 2 (autoclean)
> input 5888 0 (autoclean) [keybdev hid mousedev] ext3
> 71716 2
> jbd 51276 2 [ext3]
> sym53c8xx 67536 4
> sd_mod 13388 8
> scsi_mod 110248 5 [sg sr_mod ide-scsi sym53c8xx sd_mod]
>
> ----* /sbin/lsusb:[root at morpheus log]# /sbin/lsusb
> Bus 001 Device 001: ID 0000:0000
> Bus 001 Device 004: ID 03f0:1411 Hewlett-Packard
>
> ---* sorry, forgot this... /sbin/lspci
>
> [root at morpheus root]# lspci -vvv
> 00:00.0 Host bridge: Intel Corp. 440BX/ZX/DX - 82443BX/ZX/DX Host bridge
> (AGP disabled) (rev 02)
> Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop-
> ParErr- Stepping- SERR+ FastB2B-
> Status: Cap- 66Mhz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort-
> <TAbort- <MAbort+ >SERR- <PERR+
> Latency: 64
> Region 0: Memory at <unassigned> (32-bit, prefetchable)
[size=256M]
>
> 00:0b.0 VGA compatible controller: Cirrus Logic GD 5446 (rev 45) (prog-if
> 00 [VGA])
> Control: I/O+ Mem+ BusMaster- SpecCycle- MemWINV- VGASnoop-
> ParErr- Stepping- SERR- FastB2B-
> Status: Cap- 66Mhz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort-
> <TAbort- <MAbort- >SERR- <PERR-
> Region 0: Memory at c4000000 (32-bit, prefetchable) [size=32M]
> Region 1: Memory at c6eff000 (32-bit, non-prefetchable) [size=4K]
> Expansion ROM at <unassigned> [disabled] [size=32K]
>
> 00:0d.0 PCI bridge: Digital Equipment Corporation DECchip 21150 (rev 04)
> (prog-if 00 [Normal decode])
> Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop-
> ParErr- Stepping- SERR+ FastB2B-
> Status: Cap+ 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
> <TAbort- <MAbort- >SERR- <PERR-
> Latency: 64, cache line size 08
> Bus: primary=00, secondary=01, subordinate=01, sec-latency=64
> I/O behind bridge: 00002000-00002fff
> Memory behind bridge: c6f00000-c6ffffff
> Prefetchable memory behind bridge:
00000000fff00000-0000000000000000
> BridgeCtl: Parity+ SERR+ NoISA+ VGA- MAbort- >Reset- FastB2B-
> Capabilities: [dc] Power Management version 1
> Flags: PMEClk- DSI- D1- D2- AuxCurrent=220mA
> PME(D0-,D1-,D2-,D3hot-,D3cold-)
> Status: D0 PME-Enable- DSel=0 DScale=0 PME-
> Bridge: PM- B3+
>
> 00:0e.0 System peripheral: Compaq Computer Corporation Advanced System
> Management Controller
> Subsystem: Compaq Computer Corporation: Unknown device b0f3
> Control: I/O+ Mem+ BusMaster- SpecCycle- MemWINV- VGASnoop-
> ParErr+ Stepping- SERR+ FastB2B-
> Status: Cap- 66Mhz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort-
> <TAbort- <MAbort- >SERR- <PERR-
> Interrupt: pin A routed to IRQ 0
> Region 0: I/O ports at 1800 [size=256]
> Region 1: Memory at c6efef00 (32-bit, non-prefetchable) [size=256]
>
> 00:14.0 ISA bridge: Intel Corp. 82371AB/EB/MB PIIX4 ISA (rev 02)
> Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop-
> ParErr- Stepping- SERR- FastB2B-
> Status: Cap- 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
> <TAbort- <MAbort- >SERR- <PERR-
> Latency: 0
>
> 00:14.1 IDE interface: Intel Corp. 82371AB/EB/MB PIIX4 IDE (rev 01)
> (prog-if 80 [Master])
> Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop-
> ParErr- Stepping- SERR- FastB2B-
> Status: Cap- 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
> <TAbort- <MAbort- >SERR- <PERR-
> Latency: 64
> Region 4: I/O ports at f100 [size=16]
>
> 00:14.2 USB Controller: Intel Corp. 82371AB/EB/MB PIIX4 USB (rev 01)
> (prog-if 00 [UHCI])
> Control: I/O+ Mem- BusMaster- SpecCycle- MemWINV- VGASnoop-
> ParErr- Stepping- SERR- FastB2B-
> Status: Cap- 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
> <TAbort- <MAbort+ >SERR- <PERR-
> Interrupt: pin D routed to IRQ 0
> Region 4: I/O ports at 1000 [size=32]
>
> 00:14.3 Bridge: Intel Corp. 82371AB/EB/MB PIIX4 ACPI (rev 02)
> Control: I/O- Mem- BusMaster- SpecCycle- MemWINV- VGASnoop-
> ParErr- Stepping- SERR- FastB2B-
> Status: Cap- 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
> <TAbort- <MAbort- >SERR- <PERR-
> Interrupt: pin ? routed to IRQ 9
>
> 01:07.0 Network controller: Compaq Computer Corporation ProLiant
> Integrated Netelligent 10/100 (rev 10)
> Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop-
> ParErr+ Stepping- SERR+ FastB2B-
> Status: Cap- 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
> <TAbort- <MAbort- >SERR- <PERR-
> Latency: 64, cache line size 08
> Interrupt: pin A routed to IRQ 10
> Region 0: I/O ports at 2800 [size=16]
> Region 1: Memory at c6ffcdf0 (32-bit, non-prefetchable) [size=16]
> Expansion ROM at <unassigned> [disabled] [size=64K]
>
> 01:09.0 SCSI storage controller: LSI Logic / Symbios Logic 53c875 (rev 14)
> Subsystem: Compaq Computer Corporation Embedded Ultra Wide SCSI
> Controller
> Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV+ VGASnoop-
> ParErr+ Stepping- SERR+ FastB2B-
> Status: Cap- 66Mhz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort-
> <TAbort- <MAbort- >SERR- <PERR-
> Latency: 255 (4250ns min, 16000ns max), cache line size 08
> Interrupt: pin A routed to IRQ 11
> Region 0: I/O ports at 2000 [size=256]
> Region 1: Memory at c6ffcf00 (32-bit, non-prefetchable) [size=256]
> Region 2: Memory at c6fff000 (32-bit, non-prefetchable) [size=4K]
>
> 01:09.1 SCSI storage controller: LSI Logic / Symbios Logic 53c875 (rev 14)
> Subsystem: Compaq Computer Corporation Embedded Ultra Wide SCSI
> Controller
> Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV+ VGASnoop-
> ParErr+ Stepping- SERR+ FastB2B-
> Status: Cap- 66Mhz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort-
> <TAbort- <MAbort- >SERR- <PERR-
> Latency: 255 (4250ns min, 16000ns max), cache line size 08
> Interrupt: pin B routed to IRQ 15
> Region 0: I/O ports at 2400 [size=256]
> Region 1: Memory at c6ffce00 (32-bit, non-prefetchable) [size=256]
> Region 2: Memory at c6ffe000 (32-bit, non-prefetchable) [size=4K]
>
> 01:0d.0 USB Controller: OPTi Inc. 82C861 (rev 10) (prog-if 10 [OHCI])
> Subsystem: OPTi Inc. 82C861
> Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV+ VGASnoop-
> ParErr+ Stepping- SERR+ FastB2B-
> Status: Cap- 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
> <TAbort- <MAbort- >SERR- <PERR+
> Latency: 64, cache line size 08
> Interrupt: pin A routed to IRQ 5
> Region 0: Memory at c6ffd000 (32-bit, non-prefetchable) [size=4K]
>
> as i thought i just have the last USB Controller the OPTi....i dunno what
> is doing the other one...should i reconfigure my kernel and recompile?
>
> thx for any help getting my mouse working...
> Roger
>
>
> --
> fedora-list mailing list
> fedora-list at redhat.com
> To unsubscribe: http://www.redhat.com/mailman/listinfo/fedora-list
More information about the fedora-list
mailing list