"cdrecord" fails consistently with scsi errors
Robert P. J. Day
rpjday at mindspring.com
Fri Feb 13 11:30:26 UTC 2004
for the first time in a while, i wanted to burn a few CDs (FC2-test1,
no big surprise there). i'm running FC1, and booting *without* the SCSI
emulation feature on my inspiron 8100 with built-in ATAPI CD-RW.
just to make sure the CD writer is properly recognized, i do:
------------------------
# cdrecord -scanbus dev=ATAPI:
Cdrecord-Clone 2.01a19 (i686-redhat-linux-gnu) Copyright (C) 1995-2003 Jrg
Schilling
scsidev: 'ATAPI:'
devname: 'ATAPI'
scsibus: -1 target: -1 lun: -1
Warning: Using ATA Packet interface.
Warning: The related libscg interface code is in pre alpha.
Warning: There may be fatal problems.
Using libscg version 'schily-0.7'
scsibus0:
0,0,0 0) *
0,1,0 1) 'TOSHIBA ' 'CDRW/DVD SDR2102' '1D10' Removable CD-ROM
0,2,0 2) *
0,3,0 3) *
0,4,0 4) *
0,5,0 5) *
0,6,0 6) *
0,7,0 7) *
------------------------
looks good. then, to burn, i run:
# cdrecord -v dev=ATAPI:/dev/hdb disc1.iso
what i get (consistently, that is, five coasters in a row now) is:
-------------------------------------
Cdrecord-Clone 2.01a19 (i686-redhat-linux-gnu) Copyright (C) 1995-2003 Jrg
Schilling
TOC Type: 1 = CD-ROM
scsidev: 'ATAPI:/dev/hdb'
devname: 'ATAPI:/dev/hdb'
scsibus: -2 target: -2 lun: -2
Warning: Using ATA Packet interface.
Warning: The related libscg interface code is in pre alpha.
Warning: There may be fatal problems.
Using libscg version 'schily-0.7'
SCSI buffer size: 64512
atapi: 1
Device type : Removable CD-ROM
Version : 0
Response Format: 2
Capabilities :
Vendor_info : 'TOSHIBA '
Identifikation : 'CDRW/DVD SDR2102'
Revision : '1D10'
Device seems to be: Generic mmc2 DVD-ROM.
Current: 0x0009
Profile: 0x0010
Profile: 0x0008
Profile: 0x0009 (current)
Profile: 0x000A
Using generic SCSI-3/mmc CD-R/CD-RW driver (mmc_cdr).
Driver flags : MMC-2 SWABAUDIO BURNFREE
Supported modes: TAO PACKET SAO SAO/R96P SAO/R96R
Drive buf size : 1312768 = 1282 KB
FIFO size : 4194304 = 4096 KB
Track 01: data 632 MB
Total size: 725 MB (71:55.33) = 323650 sectors
Lout start: 726 MB (71:57/25) = 323650 sectors
Current Secsize: 2048
ATIP info from disk:
Indicated writing power: 5
Is not unrestricted
Is not erasable
Disk sub type: Medium Type A, high Beta category (A+) (3)
ATIP start of lead in: -11634 (97:26/66)
ATIP start of lead out: 359848 (79:59/73)
Disk type: Short strategy type (Phthalocyanine or similar)
Manuf. index: 3
Manufacturer: CMC Magnetics Corporation
Blocks total: 359848 Blocks current: 359848 Blocks remaining: 36198
Starting to write CD/DVD at speed 4 in real TAO mode for single session.
Last chance to quit, starting real write 0 seconds. Operation starts.
Waiting for reader process to fill input buffer ... input buffer ready.
BURN-Free is OFF.
Performing OPC...
Starting new track at sector: 0
Track 01: 142 of 632 MB written (fifo 100%) [buf 94%] 4.1x.cdrecord:
Input/output error. write_g1: scsi sendcmd: no error
CDB: 2A 00 00 01 1C D0 00 00 1F 00
status: 0x2 (CHECK CONDITION)
Sense Bytes: 70 00 03 00 00 00 00 0A 00 00 00 00 0C 00 00 00 00 00
Sense Key: 0x3 Medium Error, Segment 0
Sense Code: 0x0C Qual 0x00 (write error) Fru 0x0
Sense flags: Blk 0 (not valid)
cmd finished after 0.099s timeout 40s
write track data: error after 149323776 bytes
cdrecord: A write error occured.
cdrecord: Please properly read the error message above.
Writing time: 256.470s
Average write speed 16.8x.
Min drive buffer fill was 89%
Fixating...
Fixating time: 0.000s
cdrecord: fifo had 2416 puts and 2353 gets.
cdrecord: fifo was 0 times empty and 1988 times full, min fill was
-------------------------------
the failure isn't always at the same place, and i've never had problems
with burning before. any thoughts? is it possible the burner is bad?
i can't believe all of these CDs were flawed somehow.
thoughts?
rday
More information about the fedora-list
mailing list