Intel PRO/Wireless 2200/2915 firmware on FC5

Gregory P. Ennis PoMec at PoMec.Net
Sun Jun 18 14:41:04 UTC 2006


On Sun, 2006-06-18 at 09:12 -0500, Jeff Vian wrote:
> On Sun, 2006-06-18 at 08:51 -0500, Gregory P. Ennis wrote:
> > On Sun, 2006-06-18 at 00:49 -0400, Matthew Saltzman wrote:
> > > On Sat, 17 Jun 2006, Gregory P. Ennis wrote:
> > > 
> > > > On Wed, 2006-06-07 at 15:00 -0400, Lucas Brasilino wrote:
> > > >> Hi Dave:
> > > >>
> > > >>> > I know theres actually two threads about wireless support
> > > >>> > on FC5, but I didn't start reading it from beginning.
> > > >>> >
> > > >>> > Why not IntelPRO 2200BG/2915ABG firmware was packaged into kernel rpm,
> > > >>> > or something like it? Due licensing issues?
> > > >>>
> > > >>> Yes. There's a problem with redistribution rights.
> > > >>
> > > >> Ok, but a note at 'Release Notes' about it should be nice but not
> > > >> just `Support for wireless cards Intel(R) PRO/Wireless 2100 and
> > > >> 2200 has been added.'.
> > > >> Another thing, I think 'ipw2200' module should not be loaded if firmware
> > > >> is not present...
> > > >>
> > > >>
> > > > I just put FC5 on an HP laptop with an IntelPRO 2200BG and can not get
> > > > it to work either.  Does the firmware have to be obtained from Intel?
> > > > Is there a way to make the wireless network active?
> > > 
> > > Install ipw2200-firmware-3.0-1.lvn5 from rpm.livna.org.
> > > 
> > > -- 
> > >  		Matthew Saltzman
> > Matthew,
> > 
> > Thanks for the information!!!!  Guess I should have found that in the
> > thread, but missed it somehow when I read the messages.  I have
> > installed ipw2200 and am now able to see some wireless networks, but am
> > still having trouble connecting.  I have been able to connect to them
> > using windows so I know they are allowing connections.  
> > 
> > I have an HP Pavillion Entertainment Notebook that has a wireless toggle
> > switch that I suspect might be the "Radio Frequency Kill Switch" as part
> > of the top row of buttons.  The switched worked when windows was
> > installed, but now with FC5 installed it is not recognized; I did not
> > set up a dual boot machine.  dmesg listing includes the following error:
> > 
> > ipw2200: Detected Intel PRO/Wireless 2200BG Network Connection
> > ipw2200: Radio Frequency Kill Switch is On:
> > Kill switch must be turned off for wireless networking to work.
> > 
> > I have done a google search on this subject but have not yet found an
> > answer.  Using iwlist eth1 scan I can see the wireless networks so I
> > think my wireless card is partially working.  
> > 
> Sounds like it is receiving, but not transmitting and the kill switch is
> on the transmit side.  The kill switch has to be turned off per the
> message above.
> 
> Just on an off chance, have you tried to press the switch after power is
> applied but before the OS starts to load?  Maybe that will work,
> otherwise I have no clues at this point.
> 
> The driver was able to tell you the kill switch is on, so somehow it
> should be able to turn the switch off.
> 
Jeff,

I agree with you, but I have not found a way to turn it off yet.  I
checked the bios and the wireless feature is 'enabled', and tried your
'trick' but it did not work.  ... good idea though!!!!

Any other ideas would be appreciated,

Greg




More information about the fedora-list mailing list