Apple 30" Monitor
Konstantin Svist
fry.kun at gmail.com
Tue Jun 26 00:36:10 UTC 2007
Not 100% sure, but check in the display control panel once you have
added the "modes" line to xorg.conf
Michael J. McGillick wrote:
> Konstantin:
>
> I played around with the Fonts applet as you suggested, but no real
> difference. It did clean them up a tiny bit in the current resolution,
> but as soon as I switched to a resolution like 1920x1200, it was
> unreadably fuzzy.
>
> I also did as you suggested of placing the Modes line in my Display
> section, but no change after I restarted X.
>
> I also looked at /var/log/Xorg.0.log and saw:
>
> (II) VESA(0): Manufacturer: APP Model: 9232 Serial#: 33584150
> (II) VESA(0): Year: 2006 Week: 32
> (II) VESA(0): EDID Version: 1.3
> (II) VESA(0): Digital Display Input
> (II) VESA(0): Max H-Image Size [cm]: horiz.: 64 vert.: 40
> (II) VESA(0): Gamma: 2.20
> (II) VESA(0): DPMS capabilities: Off; RGB/Color Display
> (II) VESA(0): First detailed timing not preferred mode in violation of
> standard!(II) VESA(0): redX: 0.640 redY: 0.343 greenX: 0.292 greenY:
> 0.611
> (II) VESA(0): blueX: 0.146 blueY: 0.074 whiteX: 0.313 whiteY: 0.331
> (II) VESA(0): Manufacturer's mask: 0
> (II) VESA(0): Supported additional Video Mode:
> (II) VESA(0): clock: 71.0 MHz Image Size: 641 x 401 mm
> (II) VESA(0): h_active: 1280 h_sync: 1328 h_sync_end 1360 h_blank_end
> 1440 h_border: 0
> (II) VESA(0): v_active: 800 v_sync: 803 v_sync_end 809 v_blanking: 823
> v_border: 0
> (II) VESA(0): Supported additional Video Mode:
> (II) VESA(0): clock: 268.0 MHz Image Size: 641 x 401 mm
> (II) VESA(0): h_active: 2560 h_sync: 2608 h_sync_end 2640 h_blank_end
> 2720 h_border: 0
> (II) VESA(0): v_active: 1600 v_sync: 1603 v_sync_end 1609 v_blanking:
> 1646 v_border: 0
> (II) VESA(0): Serial No: CY6321VNUG1
> (II) VESA(0): Monitor name: Cinema HD
> (II) VESA(0): Number of EDID sections to follow: 1
> (II) VESA(0): EDID (in hex):
> (II) VESA(0): 00ffffffffffff000610329216740002
> (II) VESA(0): 201001038040287828fe87a3574a9c25
> (II) VESA(0): 13505400000001010101010101010101
> (II) VESA(0): 010101010101bc1b00a0502017303020
> (II) VESA(0): 360081912100001ab06800a0a0402e60
> (II) VESA(0): 3020360081912100001a000000ff0043
> (II) VESA(0): 5936333231564e5547310a00000000fc
> (II) VESA(0): 0043696e656d612048440a00000001b7
> (II) VESA(0): Printing DDC gathered Modelines:
> (II) VESA(0): Modeline "1280x800" 71.00 1280 1328 1360 1440 800 803
> 809 823 -hsync +vsync
> (II) VESA(0): Modeline "2560x1600" 268.00 2560 2608 2640 2720 1600
> 1603 1609 1646 -hsync +vsync
>
> And then much further down the file:
>
> (II) VESA(0): Total Memory: 256 64KB banks (16384kB)
> (II) VESA(0): <default monitor>: Using hsync range of 49.31-98.53 kHz
> (II) VESA(0): <default monitor>: Using vrefresh range of 59.86-59.91 Hz
> (II) VESA(0): Not using mode "2560x1600" (no mode of this name)
> (II) VESA(0): Not using built-in mode "1920x1440" (no mode of this name)
> (II) VESA(0): Not using built-in mode "1856x1392" (no mode of this name)
> (II) VESA(0): Not using built-in mode "1600x1200" (no mode of this name)
> (II) VESA(0): Not using built-in mode "1400x1050" (no mode of this name)
> (II) VESA(0): Not using built-in mode "1280x1024" (no mode of this name)
> (II) VESA(0): Not using built-in mode "1280x1024" (no mode of this name)
> (II) VESA(0): Not using built-in mode "1280x1024" (no mode of this name)
> (II) VESA(0): Not using built-in mode "1152x864" (no mode of this name)
> (II) VESA(0): Not using built-in mode "1024x768" (no mode of this name)
> (II) VESA(0): Not using built-in mode "1024x768" (no mode of this name)
> (II) VESA(0): Not using built-in mode "800x600" (no mode of this name)
> (II) VESA(0): Not using built-in mode "800x600" (no mode of this name)
> (II) VESA(0): Not using built-in mode "640x480" (no mode of this name)
> (II) VESA(0): Not using built-in mode "640x480" (no mode of this name)
> (II) VESA(0): Not using built-in mode "720x400" (no mode of this name)
> (II) VESA(0): Not using built-in mode "640x400" (no mode of this name)
> (II) VESA(0): Not using built-in mode "640x400" (no mode of this name)
> (II) VESA(0): Not using built-in mode "640x350" (no mode of this name)
> (II) VESA(0): Not using built-in mode "512x384" (no mode of this name)
> (II) VESA(0): Not using built-in mode "320x240" (no mode of this name)
> (II) VESA(0): Not using built-in mode "320x200" (no mode of this name)
> (II) VESA(0): Not using built-in mode "320x200" (no mode of this name)
> (WW) VESA(0): No valid modes left. Trying less strict filter...
> (II) VESA(0): <default monitor>: Using hsync range of 49.31-98.53 kHz
> (II) VESA(0): <default monitor>: Using vrefresh range of 59.86-59.91 Hz
> (II) VESA(0): Not using mode "2560x1600" (no mode of this name)
> (II) VESA(0): Not using built-in mode "1024x768" (hsync out of range)
> (II) VESA(0): Not using built-in mode "1024x768" (hsync out of range)
> (II) VESA(0): Not using built-in mode "800x600" (hsync out of range)
> (II) VESA(0): Not using built-in mode "800x600" (hsync out of range)
> (II) VESA(0): Not using built-in mode "640x480" (hsync out of range)
> (II) VESA(0): Not using built-in mode "640x480" (hsync out of range)
> (II) VESA(0): Not using built-in mode "720x400" (hsync out of range)
> (II) VESA(0): Not using built-in mode "640x400" (hsync out of range)
> (II) VESA(0): Not using built-in mode "640x400" (no mode of this name)
> (II) VESA(0): Not using built-in mode "640x350" (no mode of this name)
> (II) VESA(0): Not using built-in mode "512x384" (no mode of this name)
> (II) VESA(0): Not using built-in mode "320x240" (no mode of this name)
> (II) VESA(0): Not using built-in mode "320x200" (no mode of this name)
> (II) VESA(0): Not using built-in mode "320x200" (no mode of this name)
> (WW) VESA(0): No valid modes left. Trying less strict filter...
> (II) VESA(0): <default monitor>: Using hsync range of 49.31-98.53 kHz
> (II) VESA(0): <default monitor>: Using vrefresh range of 59.86-59.91 Hz
> (II) VESA(0): Not using mode "2560x1600" (no mode of this name)
> (II) VESA(0): Not using built-in mode "1024x768" (hsync out of range)
> (II) VESA(0): Not using built-in mode "1024x768" (hsync out of range)
> (II) VESA(0): Not using built-in mode "800x600" (hsync out of range)
> (II) VESA(0): Not using built-in mode "800x600" (hsync out of range)
> (II) VESA(0): Not using built-in mode "640x480" (hsync out of range)
> (II) VESA(0): Not using built-in mode "640x480" (hsync out of range)
> (II) VESA(0): Not using built-in mode "720x400" (hsync out of range)
> (II) VESA(0): Not using built-in mode "640x400" (hsync out of range)
> (II) VESA(0): Not using built-in mode "640x400" (hsync out of range)
> (II) VESA(0): Not using built-in mode "640x350" (hsync out of range)
> (II) VESA(0): Not using built-in mode "512x384" (hsync out of range)
> (II) VESA(0): Not using built-in mode "320x240" (hsync out of range)
> (II) VESA(0): Not using built-in mode "320x200" (hsync out of range)
> (II) VESA(0): Not using built-in mode "320x200" (hsync out of range)
> (--) VESA(0): Virtual size is 1920x1440 (pitch 1920)
> (**) VESA(0): Built-in mode "1920x1440"
> (**) VESA(0): Built-in mode "1856x1392"
> (**) VESA(0): Built-in mode "1600x1200"
> (**) VESA(0): Built-in mode "1400x1050"
> (**) VESA(0): Built-in mode "1280x1024"
> (**) VESA(0): Built-in mode "1280x1024"
> (**) VESA(0): Built-in mode "1280x1024"
> (**) VESA(0): Built-in mode "1152x864"
> (**) VESA(0): Display dimensions: (640, 400) mm
> (**) VESA(0): DPI set to (76, 91)
>
> Not sure if this points to an issue or not.
>
> - Michael
>
>
>
>
> On Mon, 2007-06-25 at 16:23 -0700, Konstantin Svist wrote:
>> Not sure about the actual resolution, but as far as fuzzy fonts go, you
>> should change anti-aliasing setting.
>> In Control Center go to Appearance & Themes -> Fonts. There's a
>> Configure button next to "Use anti-aliasing for fonts". Play around with
>> those settings and see which one works better for you. My favorite is
>> Use sub-pixel hinting RGB and Hinting style set at Full.
>> Note that only newly-launched applications will use these settings.
>> Also, I'm using FC6 with KDE, so apologies if you don't have the applet
>> in the same place.
>>
>>
>>
>> As far as resolution, have you tried adding your resolution to Display
>> subsection like so:
>>
>> SubSection "Display"
>> Viewport 0 0
>> Depth 24
>> Modes "2560x1600"
>> EndSubSection
>>
>>
>>
>>
>>
>>
>> Michael J. McGillick wrote:
>>> Hi:
>>>
>>> I'm running Fedora 7 on a Mac Pro with an ATI Radeon X1900 XT and an Apple
>>> 30" HD Cinema LCD monitor. I've been doing a lot of reading on how to
>>> properly set up my xorg.conf file, however, I've not been able to get very
>>> far. I'd appreciate any help, or pointers in the right direction.
>>>
>>> The problems I'm having are:
>>>
>>> - The highest resolution that the I can set through System > Administration
>>>> Display is 1920 x 1440 (This monitor supports 2560x1600).
>>> - In all resolutions, the font is incredibly fuzzy. I have to leave the
>>> monitor set at 1280x1024, as any higher resolution and the text is
>>> unreadable.
>>>
>>> - The background graphics and images are also fuzzy.
>>>
>>>
>>> To date, here is what I've done:
>>>
>>> - Installed Fedora - In the Gnome desktop, if I go to System >
>>> Administration > Display, on the Hardware tab, I'm told that the monitor
>>> type is Cinema HD (autoconfigured) and the Video Card is ATI Technologies
>>> Inc R580 [Radeon X1900 XT] (Primary). This leads me to believe that the
>>> Fedora installer recognized my hardware.
>>>
>>> - Examined xorg.conf - If I look in xorg.conf, I see a listing for vesa
>>> instead of the Radeon driver. I did some reading and apparently there is a
>>> problem with the current 8.37.6 version of the ATI driver in that it
>>> segfaults the X server. (Please correct me if my understanding is wrong)
>>>
>>> - Followed several different threads that talk about similar problems to
>>> mine, but never a solution posted. In many cases, the user had the same
>>> graphics card as mine, but not the same monitor.
>>>
>>> - Researched how to configure an LCD monitor in xorg.conf only to learn
>>> that most LCD monitors do not have a refresh rate in the traditional sense,
>>> and so you can leave the entire monitor section out of xorg.conf.
>>> Apparently it gets detected automatically.
>>>
>>> I'm a new user and would really like to be able to get up and running.
>>> As with any new user, I'm frustrated that I haven't been able to figure it
>>> out on my own. At this point, I'm not sure what I'm doing wrong, and could
>>> really use some help.
>>>
>>> The xorg.conf that got created was:
>>>
>>> # Xorg configuration created by system-config-display
>>>
>>> Section "ServerLayout"
>>> Identifier "single head configuration"
>>> Screen 0 "Screen0" 0 0
>>> InputDevice "Keyboard0" "CoreKeyboard"
>>> EndSection
>>>
>>> Section "InputDevice"
>>> Identifier "Keyboard0"
>>> Driver "kbd"
>>> Option "XkbModel" "pc105"
>>> Option "XkbLayout" "us"
>>> EndSection
>>>
>>> Section "Device"
>>> Identifier "Videocard0"
>>> Driver "vesa"
>>> EndSection
>>>
>>> Section "Screen"
>>> Identifier "Screen0"
>>> Device "Videocard0"
>>> DefaultDepth 24
>>> SubSection "Display"
>>> Viewport 0 0
>>> Depth 24
>>> EndSubSection
>>> EndSection
>>>
>>> Any help or guidance would be greatly appreciated. Thanks.
>>>
>>> - Michael
>>>
>>>
>
More information about the fedora-list
mailing list