Hi all,
I'm running RH 7.0 (Guiness) with the 2.2.16-22 kernel and gcc-2.96-85 and
have downloaded the Linus 2.4.9 stock kernel which I'm trying to make... I
built the patch and applied it with no apparent problem but when I try to
build the kernel I get the errors in the log below.
has anyone been here before?
1k thx - e
make[2]: Leaving directory `/usr/src/linux/drivers/ide'
make -C md
make[2]: Entering directory `/usr/src/linux/drivers/md'
make all_targets
make[3]: Entering directory `/usr/src/linux/drivers/md'
gcc -D__KERNEL__ -I/usr/src/linux/include -Wall -Wstrict-prototypes -Wno-tri
graphs -O2 -fomit-frame-pointer -fno-strict-aliasing -fno-common -pipe -mpre
ferred-stack-boundary=2 -march=i586 -c -o lvm.o lvm.c
lvm.c:2329:71: macro "min" requires 3 arguments, but only 2 given
lvm.c:2343:59: macro "min" requires 3 arguments, but only 2 given
lvm.c: In function `__extend_reduce':
lvm.c:2329: `min' undeclared (first use in this function)
lvm.c:2329: (Each undeclared identifier is reported only once
lvm.c:2329: for each function it appears in.)
lvm.c:2280: warning: `end' might be used uninitialized in this function
lvm.c:2339: warning: `end' might be used uninitialized in this function
make[3]: *** [lvm.o] Error 1
make[3]: Leaving directory `/usr/src/linux/drivers/md'
make[2]: *** [first_rule] Error 2
make[2]: Leaving directory `/usr/src/linux/drivers/md'
make[1]: *** [_subdir_md] Error 2
make[1]: Leaving directory `/usr/src/linux/drivers'
make: *** [_dir_drivers] Error 2
-----Original Message-----
From: linux-lvm-admin sistina com [mailto:linux-lvm-admin sistina com] On
Behalf Of gerry dorfam ca
Sent: Sunday, August 26, 2001 6:21 AM
To: linux-lvm sistina com
Subject: RE: [linux-lvm] Successful Upgrade to 1.0 with RH 7.1
On Sat, 25 Aug 2001, Erick Calder wrote:
started with a clean Redhat 2.4.3-12 kernel
I'm running a stock 7.0 version and downloaded the above-named kernel...
patch and compilation went ok but I can't seem to make modules... I get a
ton of errors... I realised that I needed to install the kernel-headers
for
this version but even after that I can't make the modules... I've seen a
lot
of other guys out there suffering with this but no solutions... I even
tried
changing the HOSTCC to "kgcc" in the Makefile but no dice.... so I'm
wondering what you did right... can you share?
(sorry everyone else that isn't running RH)
Well, all I did was follow the install instructions that came with the LVM
tarball to create the patch. I didn't do anything special. I wasn't able
to successfully install the newly created patch until I replaced the
kernel source with a fresh "clean" rpm.
Are you running the 2.4 kernel or are you using 2.2? That makes a big
difference as you need to add the raw.io patch to the 2.2 kernel. Also, I
don't believe that the shipped RH kernel config enables LVM as a default.
I still have the patch for 2.4.3-12. However, I doubt it would work for a
7.0 install since I'm using 7.1.
Gerry
--
"The lyfe so short, the craft so long to learne" Geoffrey Chaucer
_______________________________________________
linux-lvm mailing list
linux-lvm sistina com
http://lists.sistina.com/mailman/listinfo/linux-lvm
read the LVM HOW-TO at http://www.sistina.com/lvm/Pages/howto.html
_______________________________________________
linux-lvm mailing list
linux-lvm sistina com
http://lists.sistina.com/mailman/listinfo/linux-lvm
read the LVM HOW-TO at http://www.sistina.com/lvm/Pages/howto.html