Promise SX4 2-controllers with strange Port1 Issue
Ruben Moretti
moretti at labor-enders.de
Mon Sep 5 09:04:04 UTC 2005
Hello List Co ;)
I'm running 2.6.12 /2.6.13 kernel on a single CPU (P4-Celeron)/Fedora.
Board ASROCK 775V88 with 2 Sata ports onboard. (sata_via)
With two promise SX4 cards serving seven SATA HDs on their seven channels
(RAID). [Card1 Port 2,3,4 - Card2 Port 2,3,4]
Now I added HDDs to the controller 1 or 2. All HDs are connected as
master; one HD per channel.
Now wenn i add the HDDs on Ports 1, I get errors for the added HD, and
for the previously installed ones.
There's no irq problem and no HD or controller problem (checked this by
cross-changing).
Tested with kernels 2.6.12 /2.6.13
Log File, one with and one without HDD on Port 1 [Both Cards with HDDs on
Port 2,3,4]
Any more ideas or hint?
Thanks in advance
Ruben Moretti
--- Snip with HDD on Port 1 Card 1
Linux version 2.6.12-1.1447_FC4 (bhcompile at decompose.build.redhat.com) (gcc
version 4.0.1 20050727 (Red Hat 4.0.1-5)) #1 Fri Aug 26 20:29:51 EDT 2005
BIOS-provided physical RAM map:
BIOS-e820: 0000000000000000 - 000000000009fc00 (usable)
BIOS-e820: 000000000009fc00 - 00000000000a0000 (reserved)
BIOS-e820: 00000000000e4000 - 0000000000100000 (reserved)
BIOS-e820: 0000000000100000 - 000000003ffb0000 (usable)
BIOS-e820: 000000003ffb0000 - 000000003ffc0000 (ACPI data)
BIOS-e820: 000000003ffc0000 - 000000003fff0000 (ACPI NVS)
BIOS-e820: 000000003fff0000 - 0000000040000000 (reserved)
BIOS-e820: 00000000fffc0000 - 0000000100000000 (reserved)
127MB HIGHMEM available.
896MB LOWMEM available.
Using x86 segment limits to approximate NX protection
DMI 2.3 present.
Allocating PCI resources starting at 40000000 (gap: 40000000:bffc0000)
Built 1 zonelists
Kernel command line: ro root=/dev/md3 acpi=off pci=noacpi ide=nodma
console=ttyS0 console=tty0
ide_setup: ide=nodma : Prevented DMA
Initializing CPU#0
CPU 0 irqstacks, hard=c0458000 soft=c0457000
PID hash table entries: 4096 (order: 12, 65536 bytes)
Detected 2684.955 MHz processor.
Using tsc for high-res timesource
Console: colour VGA+ 80x25
Dentry cache hash table entries: 131072 (order: 7, 524288 bytes)
Inode-cache hash table entries: 65536 (order: 6, 262144 bytes)
Memory: 1033384k/1048256k available (2518k kernel code, 14048k reserved,
690k data, 184k init, 130752k highmem)
Checking if this processor honours the WP bit even in supervisor mode... Ok.
Security Framework v1.0.0 initialized
SELinux: Initializing.
SELinux: Starting in permissive mode
selinux_register_security: Registering secondary module capability
Capability LSM initialized as secondary
Mount-cache hash table entries: 512
monitor/mwait feature present.
using mwait in idle threads.
CPU: Trace cache: 12K uops, L1 D cache: 16K
CPU: L2 cache: 256K
Intel machine check architecture supported.
Intel machine check reporting enabled on CPU#0.
CPU0: Intel P4/Xeon Extended MCE MSRs (24) available
CPU: Intel(R) Celeron(R) CPU 2.80GHz stepping 01
Enabling fast FPU save and restore... done.
Enabling unmasked SIMD FPU exception support... done.
Checking 'hlt' instruction... OK.
checking if image is initramfs... it is
Freeing initrd memory: 1199k freed
NET: Registered protocol family 16
PCI: Using configuration type 1
mtrr: v2.0 (20020519)
ACPI: Subsystem revision 20050729
ACPI: Interpreter disabled.
Linux Plug and Play Support v0.97 (c) Adam Belay
pnp: PnP ACPI: disabled
usbcore: registered new driver usbfs
usbcore: registered new driver hub
PCI: Probing PCI hardware
PCI: Probing PCI hardware (bus 00)
PCI: Using IRQ router default [1106/3227] at 0000:00:11.0
PCI: IRQ 0 for device 0000:00:0f.1 doesn't match PIRQ mask - try
pci=usepirqmask
apm: BIOS not found.
audit: initializing netlink socket (disabled)
audit(1125392498.474:1): initialized
highmem bounce pool size: 64 pages
Total HugeTLB memory allocated, 0
VFS: Disk quotas dquot_6.5.1
Dquot-cache hash table entries: 1024 (order 0, 4096 bytes)
SELinux: Registering netfilter hooks
Initializing Cryptographic API
ksign: Installing public key data
Loading keyring
- Added public key 1C1942C715575330
- User ID: Red Hat, Inc. (Kernel Module GPG key)
pci_hotplug: PCI Hot Plug PCI Core version: 0.5
isapnp: Scanning for PnP cards...
isapnp: No Plug & Play device found
Real Time Clock Driver v1.12
Linux agpgart interface v0.101 (c) Dave Jones
agpgart: Detected VIA PT880 chipset
agpgart: AGP aperture is 64M @ 0xf8000000
PNP: No PS/2 controller found. Probing ports directly.
serio: i8042 AUX port at 0x60,0x64 irq 12
serio: i8042 KBD port at 0x60,0x64 irq 1
Serial: 8250/16550 driver $Revision: 1.90 $ 76 ports, IRQ sharing enabled
ÿttyS0 at I/O 0x3f8 (irq = 4) is a 16550A
io scheduler noop registered
io scheduler anticipatory registered
io scheduler deadline registered
io scheduler cfq registered
RAMDISK driver initialized: 16 RAM disks of 16384K size 1024 blocksize
Uniform Multi-Platform E-IDE driver Revision: 7.00alpha2
ide: Assuming 33MHz system bus speed for PIO modes; override with idebus=xx
VP_IDE: IDE controller at PCI slot 0000:00:0f.1
PCI: IRQ 0 for device 0000:00:0f.1 doesn't match PIRQ mask - try
pci=usepirqmask
PCI: Via IRQ fixup for 0000:00:0f.1, from 255 to 0
VP_IDE: chipset revision 6
VP_IDE: not 100% native mode: will probe irqs later
VP_IDE: VIA vt8237 (rev 00) IDE UDMA133 controller on pci0000:00:0f.1
ide0: BM-DMA at 0xfc00-0xfc07, BIOS settings: hda:DMA, hdb:pio
ide1: BM-DMA at 0xfc08-0xfc0f, BIOS settings: hdc:DMA, hdd:DMA
hda: WDC WD400BB-23DEA0, ATA DISK drive
ide0 at 0x1f0-0x1f7,0x3f6 on irq 14
hdc: WDC WD400BB-23DEA0, ATA DISK drive
hdd: GCR-8523B, ATAPI CD/DVD-ROM drive
ide1 at 0x170-0x177,0x376 on irq 15
hda: max request size: 128KiB
hda: Host Protected Area detected.
current capacity is 78156288 sectors (40016 MB)
native capacity is 78165360 sectors (40020 MB)
hda: Host Protected Area disabled.
hda: 78165360 sectors (40020 MB) w/2048KiB Cache, CHS=65535/16/63
hda: cache flushes not supported
hda: hda1 hda2 hda3
hdc: max request size: 128KiB
hdc: Host Protected Area detected.
current capacity is 78156288 sectors (40016 MB)
native capacity is 78165360 sectors (40020 MB)
hdc: Host Protected Area disabled.
hdc: 78165360 sectors (40020 MB) w/2048KiB Cache, CHS=65535/16/63
hdc: cache flushes not supported
hdc: hdc1 hdc2 hdc3
hdd: ATAPI 52X CD-ROM drive, 128kB Cache
Uniform CD-ROM driver Revision: 3.20
ide-floppy driver 0.99.newide
usbcore: registered new driver hiddev
usbcore: registered new driver usbhid
drivers/usb/input/hid-core.c: v2.01:USB HID core driver
mice: PS/2 mouse device common for all mice
md: md driver 0.90.1 MAX_MD_DEVS=256, MD_SB_DISKS=27
NET: Registered protocol family 2
IP: routing cache hash table of 2048 buckets, 64Kbytes
TCP established hash table entries: 262144 (order: 9, 2097152 bytes)
TCP bind hash table entries: 65536 (order: 8, 1835008 bytes)
TCP: Hash tables configured (established 262144 bind 65536)
Initializing IPsec netlink socket
NET: Registered protocol family 1
NET: Registered protocol family 17
Freeing unused kernel memory: 184k freed
input: AT Translated Set 2 keyboard on isa0060/serio0
SCSI subsystem initialized
sata_via(0000:00:0f.0): routed to hard irq line 10
ata1: SATA max UDMA/133 cmd 0xEC00 ctl 0xE802 bmdma 0xDC00 irq 10
ata2: SATA max UDMA/133 cmd 0xE400 ctl 0xE002 bmdma 0xDC08 irq 10
logips2pp: Detected unknown logitech mouse model 1
input: ImPS/2 Logitech Wheel Mouse on isa0060/serio1
ata1: dev 0 ATA, max UDMA/133, 398297088 sectors: lba48
ata1: dev 0 configured for UDMA/133
scsi0 : sata_via
ata2: dev 0 ATA, max UDMA/133, 398297088 sectors: lba48
ata2: dev 0 configured for UDMA/133
scsi1 : sata_via
Vendor: ATA Model: Maxtor 6L200M0 Rev: BANC
Type: Direct-Access ANSI SCSI revision: 05
SCSI device sda: 398297088 512-byte hdwr sectors (203928 MB)
SCSI device sda: drive cache: write back
SCSI device sda: 398297088 512-byte hdwr sectors (203928 MB)
SCSI device sda: drive cache: write back
sda: sda1
Attached scsi disk sda at scsi0, channel 0, id 0, lun 0
Vendor: ATA Model: Maxtor 6L200M0 Rev: BANC
Type: Direct-Access ANSI SCSI revision: 05
SCSI device sdb: 398297088 512-byte hdwr sectors (203928 MB)
SCSI device sdb: drive cache: write back
SCSI device sdb: 398297088 512-byte hdwr sectors (203928 MB)
SCSI device sdb: drive cache: write back
sdb: sdb1
Attached scsi disk sdb at scsi1, channel 0, id 0, lun 0
Local DIMM ECC Enabled
ata3: SATA max UDMA/133 cmd 0xF89C0200 ctl 0xF89C0238 bmdma 0x0 irq 5
ata4: SATA max UDMA/133 cmd 0xF89C0280 ctl 0xF89C02B8 bmdma 0x0 irq 5
ata5: SATA max UDMA/133 cmd 0xF89C0300 ctl 0xF89C0338 bmdma 0x0 irq 5
ata6: SATA max UDMA/133 cmd 0xF89C0380 ctl 0xF89C03B8 bmdma 0x0 irq 5
ata3: dev 0 ATA, max UDMA/133, 398297088 sectors: lba48
ata3: dev 0 configured for UDMA/133
scsi2 : sata_sx4
ata4: dev 0 ATA, max UDMA/133, 398297088 sectors: lba48
ata4: dev 0 configured for UDMA/133
scsi3 : sata_sx4
ata5: dev 0 ATA, max UDMA/133, 398297088 sectors: lba48
ata5: dev 0 configured for UDMA/133
scsi4 : sata_sx4
ata6: dev 0 ATA, max UDMA/133, 398297088 sectors: lba48
ata6: dev 0 configured for UDMA/133
scsi5 : sata_sx4
Vendor: ATA Model: Maxtor 6L200M0 Rev: BANC
Type: Direct-Access ANSI SCSI revision: 05
SCSI device sdc: 398297088 512-byte hdwr sectors (203928 MB)
SCSI device sdc: drive cache: write back
SCSI device sdc: 398297088 512-byte hdwr sectors (203928 MB)
SCSI device sdc: drive cache: write back
sdc:<3>ata3: command timeout
ata3: status=0x51 { DriveReady SeekComplete Error }
ata3: called with no error (51)!
SCSI error : <2 0 0 0> return code = 0x8000002
sdc: Current: sense key: Medium Error
Additional sense: Unrecovered read error - auto reallocate failed
end_request: I/O error, dev sdc, sector 8
Buffer I/O error on device sdc, logical block 1
ata3: command timeout
ata3: status=0x51 { DriveReady SeekComplete Error }
ata3: called with no error (51)!
SCSI error : <2 0 0 0> return code = 0x8000002
sdc: Current: sense key: Medium Error
Additional sense: Unrecovered read error - auto reallocate failed
end_request: I/O error, dev sdc, sector 8
Buffer I/O error on device sdc, logical block 1
Dev sdc: unable to read RDB block 8
unknown partition table
Attached scsi disk sdc at scsi2, channel 0, id 0, lun 0
Vendor: ATA Model: Maxtor 6L200M0 Rev: BANC
Type: Direct-Access ANSI SCSI revision: 05
SCSI device sdd: 398297088 512-byte hdwr sectors (203928 MB)
SCSI device sdd: drive cache: write back
SCSI device sdd: 398297088 512-byte hdwr sectors (203928 MB)
SCSI device sdd: drive cache: write back
sdd:<3>ata4: command timeout
ata4: status=0x51 { DriveReady SeekComplete Error }
ata4: called with no error (51)!
SCSI error : <3 0 0 0> return code = 0x8000002
sdd: Current: sense key: Medium Error
Additional sense: Unrecovered read error - auto reallocate failed
end_request: I/O error, dev sdd, sector 0
Buffer I/O error on device sdd, logical block 0
ata4: command timeout
ata4: status=0x51 { DriveReady SeekComplete Error }
ata4: called with no error (51)!
SCSI error : <3 0 0 0> return code = 0x8000002
sdd: Current: sense key: Medium Error
Additional sense: Unrecovered read error - auto reallocate failed
end_request: I/O error, dev sdd, sector 0
Buffer I/O error on device sdd, logical block 0
ata4: command timeout
ata4: status=0x51 { DriveReady SeekComplete Error }
ata4: called with no error (51)!
SCSI error : <3 0 0 0> return code = 0x8000002
sdd: Current: sense key: Medium Error
Additional sense: Unrecovered read error - auto reallocate failed
end_request: I/O error, dev sdd, sector 0
Buffer I/O error on device sdd, logical block 0
unable to read partition table
Attached scsi disk sdd at scsi3, channel 0, id 0, lun 0
Vendor: ATA Model: Maxtor 6L200M0 Rev: BANC
Type: Direct-Access ANSI SCSI revision: 05
SCSI device sde: 398297088 512-byte hdwr sectors (203928 MB)
SCSI device sde: drive cache: write back
SCSI device sde: 398297088 512-byte hdwr sectors (203928 MB)
SCSI device sde: drive cache: write back
sde:<3>ata5: command timeout
ata5: status=0x51 { DriveReady SeekComplete Error }
ata5: called with no error (51)!
SCSI error : <4 0 0 0> return code = 0x8000002
sde: Current: sense key: Medium Error
Additional sense: Unrecovered read error - auto reallocate failed
end_request: I/O error, dev sde, sector 0
Buffer I/O error on device sde, logical block 0
ata5: command timeout
ata5: status=0x51 { DriveReady SeekComplete Error }
ata5: called with no error (51)!
SCSI error : <4 0 0 0> return code = 0x8000002
sde: Current: sense key: Medium Error
Additional sense: Unrecovered read error - auto reallocate failed
end_request: I/O error, dev sde, sector 0
Buffer I/O error on device sde, logical block 0
ata5: command timeout
ata5: status=0x51 { DriveReady SeekComplete Error }
ata5: called with no error (51)!
SCSI error : <4 0 0 0> return code = 0x8000002
sde: Current: sense key: Medium Error
Additional sense: Unrecovered read error - auto reallocate failed
end_request: I/O error, dev sde, sector 0
Buffer I/O error on device sde, logical block 0
unable to read partition table
Attached scsi disk sde at scsi4, channel 0, id 0, lun 0
Vendor: ATA Model: Maxtor 6L200M0 Rev: BANC
Type: Direct-Access ANSI SCSI revision: 05
SCSI device sdf: 398297088 512-byte hdwr sectors (203928 MB)
SCSI device sdf: drive cache: write back
SCSI device sdf: 398297088 512-byte hdwr sectors (203928 MB)
SCSI device sdf: drive cache: write back
sdf:<3>ata6: command timeout
ata6: status=0x51 { DriveReady SeekComplete Error }
ata6: called with no error (51)!
SCSI error : <5 0 0 0> return code = 0x8000002
sdf: Current: sense key: Medium Error
Additional sense: Unrecovered read error - auto reallocate failed
end_request: I/O error, dev sdf, sector 0
Buffer I/O error on device sdf, logical block 0
ata6: command timeout
ata6: status=0x51 { DriveReady SeekComplete Error }
ata6: called with no error (51)!
SCSI error : <5 0 0 0> return code = 0x8000002
sdf: Current: sense key: Medium Error
Additional sense: Unrecovered read error - auto reallocate failed
end_request: I/O error, dev sdf, sector 0
Buffer I/O error on device sdf, logical block 0
ata6: command timeout
ata6: status=0x51 { DriveReady SeekComplete Error }
ata6: called with no error (51)!
SCSI error : <5 0 0 0> return code = 0x8000002
sdf: Current: sense key: Medium Error
Additional sense: Unrecovered read error - auto reallocate failed
end_request: I/O error, dev sdf, sector 0
Buffer I/O error on device sdf, logical block 0
unable to read partition table
Attached scsi disk sdf at scsi5, channel 0, id 0, lun 0
Local DIMM ECC Enabled
ata7: SATA max UDMA/133 cmd 0xF8B40200 ctl 0xF8B40238 bmdma 0x0 irq 10
ata8: SATA max UDMA/133 cmd 0xF8B40280 ctl 0xF8B402B8 bmdma 0x0 irq 10
ata9: SATA max UDMA/133 cmd 0xF8B40300 ctl 0xF8B40338 bmdma 0x0 irq 10
ata10: SATA max UDMA/133 cmd 0xF8B40380 ctl 0xF8B403B8 bmdma 0x0 irq 10
ATA: abnormal status 0x7F on port 0xF8B4021C
scsi6 : sata_sx4
ata8: dev 0 ATA, max UDMA/133, 398297088 sectors: lba48
ata8: dev 0 configured for UDMA/133
scsi7 : sata_sx4
ata9: dev 0 ATA, max UDMA/133, 398297088 sectors: lba48
ata9: dev 0 configured for UDMA/133
scsi8 : sata_sx4
ata10: dev 0 ATA, max UDMA/133, 398297088 sectors: lba48
ata10: dev 0 configured for UDMA/133
scsi9 : sata_sx4
Vendor: ATA Model: Maxtor 6L200M0 Rev: BANC
Type: Direct-Access ANSI SCSI revision: 05
SCSI device sdg: 398297088 512-byte hdwr sectors (203928 MB)
SCSI device sdg: drive cache: write back
SCSI device sdg: 398297088 512-byte hdwr sectors (203928 MB)
SCSI device sdg: drive cache: write back
sdg: unknown partition table
Attached scsi disk sdg at scsi7, channel 0, id 0, lun 0
Vendor: ATA Model: Maxtor 6L200M0 Rev: BANC
Type: Direct-Access ANSI SCSI revision: 05
SCSI device sdh: 398297088 512-byte hdwr sectors (203928 MB)
SCSI device sdh: drive cache: write back
SCSI device sdh: 398297088 512-byte hdwr sectors (203928 MB)
SCSI device sdh: drive cache: write back
sdh: sdh1
Attached scsi disk sdh at scsi8, channel 0, id 0, lun 0
Vendor: ATA Model: Maxtor 6L200M0 Rev: BANC
Type: Direct-Access ANSI SCSI revision: 05
SCSI device sdi: 398297088 512-byte hdwr sectors (203928 MB)
SCSI device sdi: drive cache: write back
SCSI device sdi: 398297088 512-byte hdwr sectors (203928 MB)
SCSI device sdi: drive cache: write back
sdi: sdi1
Attached scsi disk sdi at scsi9, channel 0, id 0, lun 0
md: raid1 personality registered as nr 3
md: Autodetecting RAID arrays.
md: autorun ...
------
lspci -v
00:00.0 Host bridge: VIA Technologies, Inc.: Unknown device 0258
Subsystem: ASRock Incorporation: Unknown device 0258
Flags: bus master, 66Mhz, medium devsel, latency 8
Memory at f8000000 (32-bit, prefetchable) [size=64M]
Capabilities: [80] AGP version 3.5
Capabilities: [50] Power Management version 2
00:00.1 Host bridge: VIA Technologies, Inc. PT880 Host Bridge
Subsystem: ASRock Incorporation: Unknown device 1258
Flags: bus master, medium devsel, latency 0
00:00.2 Host bridge: VIA Technologies, Inc. PT880 Host Bridge
Subsystem: ASRock Incorporation: Unknown device 2258
Flags: bus master, medium devsel, latency 0
00:00.3 Host bridge: VIA Technologies, Inc. PT880 Host Bridge
Subsystem: ASRock Incorporation: Unknown device 3258
Flags: bus master, medium devsel, latency 0
00:00.4 Host bridge: VIA Technologies, Inc. PT880 Host Bridge
Subsystem: ASRock Incorporation: Unknown device 4258
Flags: bus master, medium devsel, latency 0
00:00.7 Host bridge: VIA Technologies, Inc. PT880 Host Bridge
Subsystem: ASRock Incorporation: Unknown device 7258
Flags: bus master, medium devsel, latency 0
00:01.0 PCI bridge: VIA Technologies, Inc. VT8237 PCI Bridge (prog-if 00
[Normal decode])
Flags: bus master, 66Mhz, medium devsel, latency 0
Bus: primary=00, secondary=01, subordinate=01, sec-latency=0
Memory behind bridge: fc600000-fe6fffff
Prefetchable memory behind bridge: f3f00000-f7efffff
Capabilities: [70] Power Management version 2
00:0b.0 RAID bus controller: Promise Technology, Inc. PDC20621 [SATA150 SX4]
4 Channel IDE RAID Controller (rev 01)
Subsystem: Promise Technology, Inc. PDC20621 [SATA150 SX4] 4 Channel
IDE RAID Controller
Flags: bus master, 66Mhz, medium devsel, latency 96, IRQ 5
I/O ports at b000 [size=256]
I/O ports at a800 [size=256]
I/O ports at a400 [size=256]
Memory at fe900000 (32-bit, non-prefetchable) [size=1M]
Memory at febd8000 (32-bit, non-prefetchable) [size=32K]
Expansion ROM at febc0000 [disabled] [size=64K]
Capabilities: [60] Power Management version 1
00:0d.0 RAID bus controller: Promise Technology, Inc. PDC20621 [SATA150 SX4]
4 Channel IDE RAID Controller (rev 01)
Subsystem: Promise Technology, Inc. PDC20621 [SATA150 SX4] 4 Channel
IDE RAID Controller
Flags: bus master, 66Mhz, medium devsel, latency 96, IRQ 10
I/O ports at c000 [size=256]
I/O ports at b800 [size=256]
I/O ports at b400 [size=256]
Memory at fea00000 (32-bit, non-prefetchable) [size=1M]
Memory at febf0000 (32-bit, non-prefetchable) [size=32K]
Expansion ROM at febe0000 [disabled] [size=64K]
Capabilities: [60] Power Management version 1
00:0f.0 RAID bus controller: VIA Technologies, Inc. VIA VT6420 SATA RAID
Controller (rev 80)
Subsystem: ASRock Incorporation: Unknown device 3149
Flags: bus master, medium devsel, latency 32, IRQ 10
I/O ports at ec00 [size=8]
I/O ports at e800 [size=4]
I/O ports at e400 [size=8]
I/O ports at e000 [size=4]
I/O ports at dc00 [size=16]
I/O ports at d800 [size=256]
Capabilities: [c0] Power Management version 2
00:0f.1 IDE interface: VIA Technologies, Inc.
VT82C586A/B/VT82C686/A/B/VT823x/A/C PIPC Bus Master IDE (rev 06) (prog-if 8a
[Master SecP PriP])
Subsystem: ASRock Incorporation K7VT2 motherboard
Flags: bus master, medium devsel, latency 32
I/O ports at fc00 [size=16]
Capabilities: [c0] Power Management version 2
00:11.0 ISA bridge: VIA Technologies, Inc. VT8237 ISA bridge
[KT600/K8T800/K8T890 South]
Subsystem: ASRock Incorporation: Unknown device 3227
Flags: bus master, stepping, medium devsel, latency 0
Capabilities: [c0] Power Management version 2
00:12.0 Ethernet controller: VIA Technologies, Inc. VT6102 [Rhine-II] (rev
78)
Subsystem: ASRock Incorporation: Unknown device 3065
Flags: bus master, medium devsel, latency 32, IRQ 11
I/O ports at d400 [size=256]
Memory at febffc00 (32-bit, non-prefetchable) [size=256]
Capabilities: [40] Power Management version 2
01:00.0 VGA compatible controller: nVidia Corporation NV5M64 [RIVA TNT2
Model 64/Model 64 Pro] (rev 15) (prog-if 00 [VGA])
Subsystem: PROLINK Microsystems Corp Pixelview RIVA TNT2 M64
Flags: bus master, 66Mhz, medium devsel, latency 32, IRQ 11
Memory at fd000000 (32-bit, non-prefetchable) [size=16M]
Memory at f4000000 (32-bit, prefetchable) [size=32M]
Expansion ROM at fe6f0000 [disabled] [size=64K]
Capabilities: [60] Power Management version 1
Capabilities: [44] AGP version 2.0
cat /proc/interrupts
CPU0
0: 217348 XT-PIC timer
1: 44 XT-PIC i8042
2: 0 XT-PIC cascade
4: 12 XT-PIC serial
5: 135 XT-PIC libata
8: 1 XT-PIC rtc
10: 158 XT-PIC libata, libata
11: 513 XT-PIC eth0
12: 101 XT-PIC i8042
14: 4612 XT-PIC ide0
15: 5431 XT-PIC ide1
NMI: 0
ERR: 0
More information about the Ataraid-list
mailing list