FW: IA64 test report: 2.6.8-rc1 /tiger 2004-7-20: Boot Hang!
Wang, Zhenyu Z
zhenyu.z.wang at intel.com
Mon Jul 26 02:43:51 UTC 2004
Originally, the test is on a tiger with RHEL installed. The fs is ext3 as default.
Then the oops came up.
I've installed the test kernel on another tiger with Suse, reiserfs as default.
The kernel can boot successfully without any trouble.
Is it a known issue? Or what causes this happen?
thanks,
-zhen
-----Original Message-----
From: Wang, Zhenyu Z
Sent: 2004年7月20日 16:59
To: linux-ia64 at vger.kernel.org
Cc: linux-acpi
Subject: IA64 test report: 2.6.8-rc1 /tiger 2004-7-20: Boot Hang!
ACPI Test Report for 2.6 ia64 kernel
=========================
Hardware Configuration:
-----------------------
System Name: ACPI-Tiger
System Type: 4 way 900 Itanium2, tiger
M/B revision: N/A
Processor version: N/A
Firmware Versions: N/A
I/O configuration summary:
MPT scsi host driver
Seagate ST318406LC boot drive
IDE floppy and CDROM
Serial console
USB mouse
USB keyboard
Ethernet Pro 1000
Software Configuration:
1.Bk pull form lia64.bkbits.net/linux-ia64-2.5 on 7/20(Shanghai
time)
2.bk pull from linux-acpi.bkbits.net/linux-acpi-test-2.6.8 on
7/20(Shanghai time)
Kernel Config file:
arch/ia64/defconfig
ACPI Features Tested: (prioritized).
--------------------
1. Boot _fail_
2. serial console
3. ATI (run X window system)
4. usb keyboard
5. USB mouse
6. NIC (eg. Ping or ftp)
7. IDE (eg. r/w floppy or CDROM)
8. SCI (eg. Press power button)
9. Soft Power off
Linux version 2.6.8-rc1 (root at acpi-tiger) (gcc version 3.2.3 20030502 (Red Hat Linux 3.2.3-20)) #1 SMP Tue Jul 20 15:52:29 CST 2004
EFI v1.10 by INTEL: SALsystab=0x3fe4c8c0 ACPI=0x3ff84000 ACPI 2.0=0x3ff83000 MPS=0x3ff82000 SMBIOS=0xf0000
ACPI: RSDP (v002 INTEL ) @ 0x000000003ff83000
ACPI: XSDT (v001 INTEL SR870BN4 0x01072002 MSFT 0x00010013) @ 0x000000003ff83090
ACPI: FADT (v003 INTEL SR870BN4 0x01072002 MSFT 0x00010013) @ 0x000000003ff83138
ACPI: MADT (v001 INTEL SR870BN4 0x01072002 MSFT 0x00010013) @ 0x000000003ff83230
ACPI: DSDT (v001 Intel SR870BN4 0x00000000 MSFT 0x0100000d) @ 0x0000000000000000
efi.trim_top: ignoring 4KB of memory at 0x0 due to granule hole at 0x0
efi.trim_top: ignoring 24KB of memory at 0x1000 due to granule hole at 0x0
efi.trim_top: ignoring 8KB of memory at 0x7000 due to granule hole at 0x0
efi.trim_top: ignoring 484KB of memory at 0x9000 due to granule hole at 0x0
efi.trim_top: ignoring 4KB of memory at 0x84000 due to granule hole at 0x0
efi.trim_top: ignoring 108KB of memory at 0x85000 due to granule hole at 0x0
efi.trim_bottom: ignoring 15360KB of memory at 0x100000 due to granule hole at 0x0
SAL 3.1: Intel Corp SR870BN4 version 3.0
SAL Platform features: BusLock IRQ_Redirection
SAL: AP wakeup using external interrupt vector 0xf0
iosapic_system_init: Disabling PC-AT compatible 8259 interrupts
ACPI: Local APIC address 0xc0000000fee00000
PLATFORM int CPEI (0x3): GSI 22 (level, low) -> CPU 0 (0xc218) vector 30
register_intr: changing vector 39 from IO-SAPIC-edge to IO-SAPIC-level
4 CPUs available, 4 CPUs total
Registering legacy COM ports for serial console
MCA related initialization done
On node 0 totalpages: 64121
DMA zone: 64121 pages, LIFO batch:4
Normal zone: 0 pages, LIFO batch:1
HighMem zone: 0 pages, LIFO batch:1
Built 1 zonelists
Kernel command line: BOOT_IMAGE=scsi0:¥EFI¥redhat¥vmlinux.26 root=/dev/sda2 console=ttyS1,9600n8 console=tty0 ro
PID hash table entries: 2048 (order 11: 32768 bytes)
CPU 0: base freq=199.458MHz, ITC ratio=14/2, ITC freq=1396.209MHz+/--1ppm
Console: colour VGA+ 80x25
Dentry cache hash table entries: 131072 (order: 6, 1048576 bytes)
Inode-cache hash table entries: 65536 (order: 5, 524288 bytes)
Memory: 1008192k/1025936k available (7281k code, 17360k reserved, 3306k data, 208k init)
McKinley Errata 9 workaround not needed; disabling it
Calibrating delay loop... 2089.76 BogoMIPS
Mount-cache hash table entries: 1024 (order: 0, 16384 bytes)
Boot processor id 0x0/0xc218
task migration cache decay timeout: 10 msecs.
CPU 1: synchronized ITC with CPU 0 (last diff -1 cycles, maxerr 513 cycles)
CPU 1: base freq=199.458MHz, ITC ratio=14/2, ITC freq=1396.209MHz+/--1ppm
Calibrating delay loop... 2089.76 BogoMIPS
CPU 2: synchronized ITC with CPU 0 (last diff -1 cycles, maxerr 513 cycles)
CPU 2: base freq=199.458MHz, ITC ratio=14/2, ITC freq=1396.209MHz+/--1ppm
Calibrating delay loop... 2089.76 BogoMIPS
CPU 3: synchronized ITC with CPU 0 (last diff -1 cycles, maxerr 513 cycles)
CPU 3: base freq=199.458MHz, ITC ratio=14/2, ITC freq=1396.209MHz+/--1ppm
Calibrating delay loop... 2089.76 BogoMIPS
Brought up 4 CPUs
Total of 4 processors activated (8359.04 BogoMIPS).
NET: Registered protocol family 16
ACPI: Subsystem revision 20040715
ACPI: Interpreter enabled
ACPI: Using IOSAPIC for interrupt routing
ACPI: PCI Root Bridge [PCI0] (00:00)
PCI: Ignoring BAR0-3 of IDE controller 0000:00:1f.1
ACPI: PCI Root Bridge [PCI1] (00:02)
ACPI: PCI Root Bridge [PCI3] (00:09)
ACPI: PCI Root Bridge [PCI4] (00:0f)
ACPI: Device [CSFF] status [00000008]: functional but not present; setting present
ACPI: PCI Root Bridge [CSFF] (00:ff)
SCSI subsystem initialized
usbcore: registered new driver usbfs
usbcore: registered new driver hub
PCI: Using ACPI for IRQ routing
GSI 16 (level, low) -> CPU 2 (0xc418) vector 48
ACPI: PCI interrupt 0000:00:1d.0[A] -> GSI 16 (level, low) -> IRQ 48
GSI 19 (level, low) -> CPU 2 (0xc418) vector 49
ACPI: PCI interrupt 0000:00:1d.1[B] -> GSI 19 (level, low) -> IRQ 49
GSI 23 (level, low) -> CPU 2 (0xc418) vector 50
ACPI: PCI interrupt 0000:00:1d.7[D] -> GSI 23 (level, low) -> IRQ 50
ACPI: PCI interrupt 0000:00:1f.1[A]: no GSI
GSI 18 (level, low) -> CPU 2 (0xc418) vector 51
ACPI: PCI interrupt 0000:01:00.0[A] -> GSI 18 (level, low) -> IRQ 51
GSI 71 (level, low) -> CPU 2 (0xc418) vector 52
ACPI: PCI interrupt 0000:03:1f.0[A] -> GSI 71 (level, low) -> IRQ 52
GSI 28 (level, low) -> CPU 2 (0xc418) vector 53
ACPI: PCI interrupt 0000:06:02.0[A] -> GSI 28 (level, low) -> IRQ 53
GSI 29 (level, low) -> CPU 2 (0xc418) vector 54
ACPI: PCI interrupt 0000:06:02.1[B] -> GSI 29 (level, low) -> IRQ 54
GSI 47 (level, low) -> CPU 2 (0xc418) vector 55
ACPI: PCI interrupt 0000:06:1f.0[A] -> GSI 47 (level, low) -> IRQ 55
GSI 119 (level, low) -> CPU 2 (0xc418) vector 56
ACPI: PCI interrupt 0000:0a:1f.0[A] -> GSI 119 (level, low) -> IRQ 56
GSI 95 (level, low) -> CPU 2 (0xc418) vector 57
ACPI: PCI interrupt 0000:0c:1f.0[A] -> GSI 95 (level, low) -> IRQ 57
GSI 167 (level, low) -> CPU 2 (0xc418) vector 58
ACPI: PCI interrupt 0000:10:1f.0[A] -> GSI 167 (level, low) -> IRQ 58
GSI 120 (level, low) -> CPU 2 (0xc418) vector 59
ACPI: PCI interrupt 0000:12:01.0[A] -> GSI 120 (level, low) -> IRQ 59
GSI 143 (level, low) -> CPU 2 (0xc418) vector 60
ACPI: PCI interrupt 0000:12:1f.0[A] -> GSI 143 (level, low) -> IRQ 60
perfmon: version 2.0 IRQ 238
perfmon: Itanium 2 PMU detected, 16 PMCs, 18 PMDs, 4 counters (47 bits)
PAL Information Facility v0.5
perfmon: added sampling format default_format
perfmon_default_smpl: default_format v2.0 registered
Total HugeTLB memory allocated, 0
Installing knfsd (copyright (C) 1996 okir at monad.swb.de).
udf: registering filesystem
Initializing Cryptographic API
ACPI: Power Button (FF) [PWRF]
ACPI: Processor [CPU0] (supports C1)
ACPI: Processor [CPU1] (supports C1)
ACPI: Processor [CPU2] (supports C1)
ACPI: Processor [CPU3] (supports C1)
EFI Time Services Driver v0.4
Serial: 8250/16550 driver $Revision: 1.90 $ 4 ports, IRQ sharing disabled
acpi_serial_port: zero-length IO port range?
ttyS0 at I/O 0x3f8 (irq = 44) is a 16550A
acpi_serial_port: zero-length IO port range?
ttyS1 at I/O 0x2f8 (irq = 45) is a 16550A
RAMDISK driver initialized: 16 RAM disks of 4096K size 1024 blocksize
loop: loaded (max 8 devices)
Intel(R) PRO/1000 Network Driver - version 5.2.52-k4
Copyright (c) 1999-2004 Intel Corporation.
ACPI: PCI interrupt 0000:01:00.0[A] -> GSI 18 (level, low) -> IRQ 51
e1000: eth0: e1000_probe: Intel(R) PRO/1000 Network Connection
ACPI: PCI interrupt 0000:12:01.0[A] -> GSI 120 (level, low) -> IRQ 59
e1000: eth1: e1000_probe: Intel(R) PRO/1000 Network Connection
Ethernet Channel Bonding Driver: v2.6.0 (January 14, 2004)
bonding: Warning: either miimon or arp_interval and arp_ip_target module parameters must be specified, otherwise bonding will not detect link failures! see bonding.txt for details.
Uniform Multi-Platform E-IDE driver Revision: 7.00alpha2
ide: Assuming 33MHz system bus speed for PIO modes; override with idebus=xx
st: Version 20040403, fixed bufsize 32768, s/g segs 256
osst :I: Tape driver with OnStream support version 0.99.1
osst :I: $Id: osst.c,v 1.70 2003/12/23 14:22:12 wriede Exp $
Fusion MPT base driver 3.01.09
Copyright (c) 1999-2004 LSI Logic Corporation
ACPI: PCI interrupt 0000:06:02.0[A] -> GSI 28 (level, low) -> IRQ 53
mptbase: Initiating ioc0 bringup
ioc0: 53C1030: Capabilities={Initiator}
ACPI: PCI interrupt 0000:06:02.1[B] -> GSI 29 (level, low) -> IRQ 54
mptbase: Initiating ioc1 bringup
ioc1: 53C1030: Capabilities={Initiator}
Fusion MPT SCSI Host driver 3.01.09
scsi0 : ioc0: LSI53C1030, FwRev=01030600h, Ports=1, MaxQ=255, IRQ=53
Using anticipatory io scheduler
Vendor: SEAGATE Model: ST318406LC Rev: 8A03
Type: Direct-Access ANSI SCSI revision: 03
SCSI device sda: 35566478 512-byte hdwr sectors (18210 MB)
SCSI device sda: drive cache: write through
sda: sda1 sda2 sda3
Attached scsi disk sda at scsi0, channel 0, id 0, lun 0
Attached scsi generic sg0 at scsi0, channel 0, id 0, lun 0, type 0
Vendor: ESG-SHV Model: SCA HSBP M17 Rev: 0101
Type: Processor ANSI SCSI revision: 02
Attached scsi generic sg1 at scsi0, channel 0, id 6, lun 0, type 3
scsi1 : ioc1: LSI53C1030, FwRev=01030600h, Ports=1, MaxQ=255, IRQ=54
ACPI: PCI interrupt 0000:00:1d.7[D] -> GSI 23 (level, low) -> IRQ 50
ehci_hcd 0000:00:1d.7: Intel Corp. 82801DB (ICH4) USB2 EHCI Controller
ehci_hcd 0000:00:1d.7: irq 50, pci mem c0000000f9ff0000
ehci_hcd 0000:00:1d.7: new USB bus registered, assigned bus number 1
PCI: slot 0000:00:1d.7 has incorrect PCI cache line size of 0 bytes, correcting to 128
ehci_hcd 0000:00:1d.7: USB 2.0 enabled, EHCI 1.00, driver 2004-May-10
hub 1-0:1.0: USB hub found
hub 1-0:1.0: 4 ports detected
USB Universal Host Controller Interface driver v2.2
ACPI: PCI interrupt 0000:00:1d.0[A] -> GSI 16 (level, low) -> IRQ 48
uhci_hcd 0000:00:1d.0: Intel Corp. 82801DB (ICH4) USB UHCI #1
uhci_hcd 0000:00:1d.0: irq 48, io base 0000000000004cc0
uhci_hcd 0000:00:1d.0: new USB bus registered, assigned bus number 2
hub 2-0:1.0: USB hub found
hub 2-0:1.0: 2 ports detected
ACPI: PCI interrupt 0000:00:1d.1[B] -> GSI 19 (level, low) -> IRQ 49
uhci_hcd 0000:00:1d.1: Intel Corp. 82801DB (ICH4) USB UHCI #2
uhci_hcd 0000:00:1d.1: irq 49, io base 0000000000004ce0
uhci_hcd 0000:00:1d.1: new USB bus registered, assigned bus number 3
hub 3-0:1.0: USB hub found
hub 3-0:1.0: 2 ports detected
usbcore: registered new driver hiddev
usbcore: registered new driver usbhid
drivers/usb/input/hid-core.c: v2.0:USB HID core driver
mice: PS/2 mouse device common for all mice
EFI Variables Facility v0.08 2004-May-17
NET: Registered protocol family 2
IP: routing cache hash table of 16384 buckets, 256Kbytes
TCP: Hash tables configured (established 131072 bind 65536)
arp_tables: (C) 2002 David S. Miller
NET: Registered protocol family 1
usb 3-1: new full speed USB device using address 2
hub 3-1:1.0: USB hub found
hub 3-1:1.0: 7 ports detected
NET: Registered protocol family 17
kjournald starting. Commit interval 5 seconds
EXT3-fs: mounted filesystem with ordered data mode.
VFS: Mounted root (ext3 filesy>tem) r1.1:only.
owFspeid UuBudedike uelnm addre 208kB fhelper[221]: Unsupported data reference 8821862825984 [1]
Modules linked in:
Pid: 221, CPU 3, comm: khelper
psr : 00001010085a2010 ifs : 8000000000000813 ip : [<a0000001005fed30>] Not tainted
ip is at sba_alloc_range+0x50/0x1280
unat: 0000000000000000 pfs : 0000000000000814 rsc : 0000000000000003
rnat: 0000000000000000 bsps: 0000000000000000 pr : 0000000000065995
ldrs: 0000000000000000 ccv : 0000000000000000 fpsr: 0009804c8a70033f
csd : 0000000000000000 ssd : 0000000000000000
b0 : a000000100600f80 b6 : a000000100308d00 b7 : a00000010055e3a0
f6 : 1003e6db6db6db6db6db7 f7 : 1003e000000000000f763
f8 : 100059dfff62000000000 f9 : 1003e000000000006c3b5
f10 : 1003e0000000000001212 f11 : 1003e0000000000007e7e
r1 : a000000100c3e560 r2 : e000000004848000 r3 : 0000000000001212
r8 : 0000000000000000 r9 : 0000000000000000 r10 : a000000100a57e48
r11 : 0000000000000040 r12 : e00000003cfd7510 r13 : e00000003cfd0000
r14 : e000000001118000 r15 : 0000000000000040 r16 : e00000003cff8000
r17 : 0000000000001000 r18 : e000000004849000 r19 : 0000000000001000
r20 : e00000003dd99000 r21 : e00000000177af40 r22 : 0000000000000000
r23 : a000000100a7fce8 r24 : 0000000000000000 r25 : e00000003dd98fff
r26 : e00000000177af58 r27 : 0000000000000000 r28 : a0000001005fed20
r29 : e00000003dd98fff r30 : 0000000000000001 r31 : 0000000000000038
Call Trace:
[<a000000100019600>] show_stack+0x80/0xa0
sp=e00000003cfd7070 bsp=e00000003cfd1b10
[<a00000010003fd10>] die+0x1d0/0x280
sp=e00000003cfd7240 bsp=e00000003cfd1ae8
[<a000000100040ae0>] ia64_fault+0x180/0xcc0
sp=e00000003cfd7240 bsp=e00000003cfd1aa8
[<a000000100012180>] ia64_leave_kernel+0x0/0x260
sp=e00000003cfd7340 bsp=e00000003cfd1aa8
[<a0000001005fed30>] sba_alloc_range+0x50/0x1280
sp=e00000003cfd7510 bsp=e00000003cfd1a10
[<a000000100600f80>] sba_map_sg+0x380/0x740
sp=e00000003cfd7510 bsp=e00000003cfd1988
[<a00000010055b010>] mptscsih_AddSGE+0xf0/0x740
sp=e00000003cfd7520 bsp=e00000003cfd1910
[<a00000010055e9d0>] mptscsih_qcmd+0x630/0xba0
sp=e00000003cfd7530 bsp=e00000003cfd18a8
[<a00000010048f2c0>] scsi_dispatch_cmd+0x480/0x6a0
sp=e00000003cfd7530 bsp=e00000003cfd1870
[<a00000010049d800>] scsi_request_fn+0x5a0/0xac0
sp=e00000003cfd7540 bsp=e00000003cfd1750
[<a0000001003ced00>] __generic_unplug_device+0xc0/0xe0
sp=e00000003cfd7540 bsp=e00000003cfd1730
[<a0000001003ceda0>] generic_unplug_device+0x80/0xe0
sp=e00000003cfd7540 bsp=e00000003cfd1710
[<a0000001003cee90>] blk_backing_dev_unplug+0x90/0xa0
sp=e00000003cfd7540 bsp=e00000003cfd16f0
[<a00000010012a020>] sync_buffer+0x100/0x120
sp=e00000003cfd7540 bsp=e00000003cfd16d8
[<a00000010012a480>] __wait_on_buffer+0x1e0/0x200
sp=e00000003cfd7540 bsp=e00000003cfd16b0
[<a00000010012e230>] __bread_slow+0x150/0x1a0
sp=e00000003cfd75a0 bsp=e00000003cfd1690
[<a00000010012eb00>] __bread+0x60/0x80
sp=e00000003cfd75a0 bsp=e00000003cfd1668
[<a0000001001bb9e0>] ext3_get_branch+0xc0/0x2a0
sp=e00000003cfd75a0 bsp=e00000003cfd1620
[<a0000001001bc8e0>] ext3_get_block_handle+0xc0/0x6a0
sp=e00000003cfd75a0 bsp=e00000003cfd1588
[<a00000010017a390>] do_mpage_readpage+0x650/0x680
sp=e00000003cfd7620 bsp=e00000003cfd14e0
[<a00000010017a4f0>] mpage_readpages+0x130/0x2a0
sp=e00000003cfd7780 bsp=e00000003cfd1478
[<a0000001001bee50>] ext3_readpages+0x30/0x60
sp=e00000003cfd7820 bsp=e00000003cfd1448
[<a0000001000ef460>] read_pages+0x280/0x2a0
sp=e00000003cfd7820 bsp=e00000003cfd13d0
[<a0000001000efab0>] do_page_cache_readahead+0x210/0x440
sp=e00000003cfd78b0 bsp=e00000003cfd1350
[<a0000001000efe40>] page_cache_readahead+0x160/0x520
sp=e00000003cfd78c0 bsp=e00000003cfd1300
[<a0000001000deac0>] do_generic_mapping_read+0x1a0/0x800
sp=e00000003cfd78c0 bsp=e00000003cfd1258
[<a0000001000df730>] __generic_file_aio_read+0x370/0x400
sp=e00000003cfd7920 bsp=e00000003cfd11e8
[<a0000001000df820>] generic_file_aio_read+0x60/0xc0
sp=e00000003cfd7940 bsp=e00000003cfd11b8
[<a000000100127130>] do_sync_read+0x110/0x160
sp=e00000003cfd7950 bsp=e00000003cfd1178
[<a000000100127390>] vfs_read+0x210/0x2c0
sp=e00000003cfd79d0 bsp=e00000003cfd1130
[<a000000100141200>] kernel_read+0x60/0xa0
sp=e00000003cfd79d0 bsp=e00000003cfd10f8
[<a0000001001923f0>] load_script+0x550/0x580
sp=e00000003cfd79e0 bsp=e00000003cfd10b8
[<a0000001001436a0>] search_binary_handler+0x400/0x7a0
sp=e00000003cfd7a70 bsp=e00000003cfd1038
[<a000000100143d80>] do_execve+0x340/0x3e0
sp=e00000003cfd7a70 bsp=e00000003cfd0fc8
[<a00000010001b250>] sys_execve+0x90/0xe0
sp=e00000003cfd7c60 bsp=e00000003cfd0f58
[<a000000100011710>] ia64_execve+0x30/0x160
sp=e00000003cfd7c60 bsp=e00000003cfd0f30
[<a000000100012000>] ia64_ret_from_syscall+0x0/0x20
sp=e00000003cfd7c60 bsp=e00000003cfd0f30
[<a000000100011e20>] execve+0x0/0x20
sp=e00000003cfd7e30 bsp=e00000003cfd0f30
[<a0000001000be7e0>] ____call_usermodehelper+0x160/0x1a0
sp=e00000003cfd7e30 bsp=e00000003cfd0f18
[<a00000010001b5a0>] kernel_thread_helper+0xe0/0x100
sp=e00000003cfd7e30 bsp=e00000003cfd0ef0
[<a000000100009060>] start_kernel_thread+0x20/0x40
sp=e00000003cfd7e30 bsp=e00000003cfd0ef0
More information about the Ext3-users
mailing list