Fedora core 4 avmdsl card capi (die zweite)
Christoph Wickert
christoph.wickert at gmx.de
Mon Oct 24 16:32:25 UTC 2005
Am Montag, den 24.10.2005, 17:02 +0200 schrieb tuxbase:
> Hallo
>
> funktioniert immer noch nicht!
>
>
> dmesg:
> ISDN subsystem Rev: 1.1.2.3/1.1.2.3/1.1.2.2/1.1.2.3/1.1.2.2/1.1.2.2
> loaded
> HiSax: Linux Driver for passive ISDN cards
> HiSax: Version 3.5 (module)
> HiSax: Layer1 Revision 2.46.2.5
> HiSax: Layer2 Revision 2.30.2.4
> HiSax: TeiMgr Revision 2.20.2.3
> HiSax: Layer3 Revision 2.22.2.3
> HiSax: LinkLayer Revision 2.59.2.4
> HiSax module removed
> ISDN-subsystem unloaded
> ip_tables: (C) 2000-2002 Netfilter core team
> ip_conntrack version 2.1 (4095 buckets, 32760 max) - 248 bytes per
> conntrack
> Vendor: ICSI Model: IC1210 CF Rev: 1.6B
> Type: Direct-Access ANSI SCSI revision: 00
> Vendor: ICSI Model: IC1210 MS Rev: 1.6B
> Type: Direct-Access ANSI SCSI revision: 00
> Vendor: ICSI Model: IC1210 MMC/SD Rev: 1.6B
> Type: Direct-Access ANSI SCSI revision: 00
> Vendor: ICSI Model: IC1210 SM Rev: 1.6B
> Type: Direct-Access ANSI SCSI revision: 00
> usb-storage: device scan complete
> eth0: link up, 100Mbps, full-duplex, lpa 0x45E1
> NET: Registered protocol family 10
> Disabled Privacy Extensions on device c0475600(lo)
> IPv6 over IPv4 tunneling driver
> CAPI Subsystem Rev 1.1.2.8
> capifs: Rev 1.1.2.3
> capi20: Rev 1.1.2.7: started up with major 68 (middleware+capifs)
> fcdsl2: module license 'Proprietary' taints kernel.
> fcdsl2: AVM FRITZ!Card DSL v2.0 driver, revision 0.3.2
> fcdsl2: (fcdsl2 built on Oct 23 2005 at 18:43:22)
> fcdsl2: -- 32 bit CAPI driver --
bis dahin ok, geht bei mir weiter mit:
> ACPI: PCI Interrupt 0000:00:0f.0[A] -> Link [LNKD] -> GSI 11 (level, low) -> IRQ 11
> fcpci: AVM FRITZ!Card PCI found: port 0xbc00, irq 11
> fcpci: Loading...
> fcpci: Driver 'fcpci' attached to fcpci-stack. (152)
> fcpci: Stack version 3.11-07
> kcapi: Controller 1: fcpci-bc00-11 attached
> kcapi: card 1 "fcpci-bc00-11" ready.
> fcpci: Loaded.
> kcapi: contr 1 set trace=0
> kcapi: contr 1 set trace=0
> kcapi: contr 1 set trace=4
> kcapi: contr 1 set trace=0
>
> /etc/capi.conf
> fcdsl2 fds2base.bin - - - - 1
Was soll die 1 am Ende? Controller 1? Ich habe das bei meiner Fritz-DSL
v.1 nicht und in der capi.conf, die ich mal angehängt habe, ist es auch
nicht.
>
> >lsmod | egrep "capi|fcd"
> fcdsl2 841124 0
> capi 17921 0
> capifs 6217 2 capi
> kernelcapi 47201 2 fcdsl2,capi
korrekt
> >capiinfo
> capi not installed - No such device or address (6)
hast Du zu diesem Zeitpunkt ein /dev/capi20?
ls /dev/capi*
/dev/capi20
/dev/capi:
(/dev/capi ist leer und wird erst bevölkert, wenn eine Verbindung
besteht.)
>
> rpm -qa | grep fcp
> fcpci-03.11.07-7.rhfc4.at
> fcpci-kmdl-2.6.13-1.1526_FC4-03.11.07-7.rhfc4.at
Moment, Moment! Du hast eine Fritzcard DSL und eine Fritzcard PCI? In
eimem Rechner?
Abgesehen davon ist das nicht der aktuelle Kernel, 1532 ist aktuell. Für
den hat Axel aber noch keine Kernelmodule, für die DSL-Karte sowieso
nicht. Also ist Eigenbau angesagt.
>
> und
>
> fcdsl2-suse93-3.11-07.tar.gz ist installiert
>
Wieso "und"? Das war ein "entweder ... oder", nicht beides!
> Gruß
> Bruno
>
Alles unklar? ;-)
Christoph
-------------- next part --------------
# card file proto io irq mem cardnr options
#b1isa b1.t4 DSS1 0x150 7 - - P2P
#b1pci b1.t4 DSS1 - - - -
#b1pci - - - - - -
#b1pci - - - - - - P2P
#b1pciv4 b1.t4 - - - - -
#c2 c2.bin DSS1 - - - -
#c2 - DSS1 - - - -
#c4 c4.bin DSS1 - - - -
#c4 - DSS1 - - - -
#c4 - DSS1 - - - - P2P
#c4 c4.bin DSS1 - - - - P2P
#t1isa t1.t4 DSS1 0x340 9 - 0
#t1pci t1.t4 DSS1 - - - -
#fcclassic - - 0x300 5 - -
fcpci - - - - - -
#fcpcmcia - - - - - -
#fcpnp - - 0x150 10 - -
#fcdsl fdslbase.bin - - - - -
#fcdsl2 fds2base.bin - - - - -
#fcusb - - - - - -
#fcusb20 fus2base.frm - - - - -
#fcusb21 fus3base.frm - - - - -
#fxusb - - - - - -
#fcdslusb fdsubase.frm - - - - -
#fcdslsl fdssbase.bin - - - - -
#fcdslslusb fdlubase.frm - - - - -
More information about the Fedora-de-list
mailing list