[Date Prev][Date Next]   [Thread Prev][Thread Next]   [Thread Index] [Date Index] [Author Index]

CD burning faulty



Does anyone know what is wrong? The Cd is opened, the cue sheet is sent, then 
it is closed and the burning fails, but nothing is ever written to the CD and 
the CD is destroyed.

Here is the output:

System
-----------------------
K3b Version: 1.0.3

KDE Version: 3.5.7-22.fc8 Fedora
QT Version:  3.3.8
Kernel:      2.6.23-0.171.rc5.git1.fc8
Devices
-----------------------
TSSTcorp CD/DVDW SH-S183L SB01 (/dev/sr0, ) [CD-R, CD-RW, CD-ROM, DVD-ROM, 
DVD-R, DVD-RW, DVD-R DL, DVD+R, DVD+RW, DVD+R DL] [DVD-ROM, DVD-R Sequential, 
DVD-R Dual Layer Sequential, DVD-R Dual Layer Jump, DVD-RAM, DVD-RW 
Restricted Overwrite, DVD-RW Sequential, DVD+RW, DVD+R, DVD+R Dual Layer, 
CD-ROM, CD-R, CD-RW] [SAO, TAO, RAW, SAO/R96P, SAO/R96R, RAW/R16, RAW/R96P, 
RAW/R96R, Restricted Overwrite, Layer Jump]

Used versions
-----------------------
cdrecord: 1.1.6

cdrecord
-----------------------
scsidev: '/dev/sr0'
devname: '/dev/sr0'
scsibus: -2 target: -2 lun: -2
Linux sg driver version: 3.5.27
Wodim version: 1.1.6
SCSI buffer size: 64512
Beginning DMA speed test. Set CDR_NODMATEST environment variable if device
communication breaks or freezes immediately after that.
TOC Type: 1 = CD-ROM
Driveropts: 'burnfree'
Device type    : Removable CD-ROM
Version        : 5
Response Format: 2
Capabilities   : 
Vendor_info    : 'TSSTcorp'
Identification : 'CD/DVDW SH-S183L'
Revision       : 'SB01'
Device seems to be: Generic mmc2 DVD-R/DVD-RW.
Current: 0x0009 (CD-R)
Profile: 0x0015 (DVD-R/DL sequential recording) 
Profile: 0x0016 (DVD-R/DL layer jump recording) 
Profile: 0x002B (DVD+R/DL) 
Profile: 0x001B (DVD+R) 
Profile: 0x001A (DVD+RW) 
Profile: 0x0014 (DVD-RW sequential recording) 
Profile: 0x0013 (DVD-RW restricted overwrite) 
Profile: 0x0012 (DVD-RAM) 
Profile: 0x0011 (DVD-R sequential recording) 
Profile: 0x0010 (DVD-ROM) 
Profile: 0x000A (CD-RW) 
Profile: 0x0009 (CD-R) (current)
Profile: 0x0008 (CD-ROM) 
Profile: 0x0002 (Removable disk) 
Using generic SCSI-3/mmc   CD-R/CD-RW driver (mmc_cdr).
Driver flags   : MMC-3 SWABAUDIO BURNFREE 
Supported modes: TAO PACKET SAO SAO/R96R RAW/R16 RAW/R96P RAW/R96R
Drive buf size : 1058816 = 1034 KB
FIFO size      : 4194304 = 4096 KB
Track 01: data   163 MB        
Total size:      187 MB (18:33.25) = 83494 sectors
Lout start:      187 MB (18:35/19) = 83494 sectors
Current Secsize: 2048
ATIP info from disk:
  Indicated writing power: 5
  Is not unrestricted
  Is not erasable
  Disk sub type: Medium Type A, high Beta category (A+) (3)
  ATIP start of lead in:  -11634 (97:26/66)
  ATIP start of lead out: 359848 (79:59/73)
Disk type:    Short strategy type (Phthalocyanine or similar)
Manuf. index: 3
Manufacturer: CMC Magnetics Corporation
Blocks total: 359848 Blocks current: 359848 Blocks remaining: 276354
Starting to write CD/DVD at speed  48.0 in real SAO mode for single session.
Last chance to quit, starting real write in  2 seconds.
Speed set to 8468 KB/s
   1 seconds.
   0 seconds. Operation starts.
Waiting for reader process to fill input buffer ... input buffer ready.
Performing OPC...
Sending CUE sheet...
Errno: 5 (Input/output error), write_g1 scsi sendcmd: no error
CDB:  2A 00 FF FF FF 6A 00 00 1F 00
status: 0x2 (CHECK CONDITION)
Sense Bytes: 70 00 04 00 00 00 00 0A 00 00 00 00 08 03 00 00
Sense Key: 0x4 Hardware Error, Segment 0
Sense Code: 0x08 Qual 0x03 (logical unit communication crc error 
(ultra-dma/32)) Fru 0x0
Sense flags: Blk 0 (not valid) 
cmd finished after 0.847s timeout 200s
Writing pregap for track 1 at -150
write track pad data: error after 0 bytes
BFree: 1025 K BSize: 1034 K
Starting new track at sector: 0
Track 01:    0 of  163 MB written.
Errno: 5 (Input/output error), write_g1 scsi sendcmd: no error
CDB:  2A 00 00 00 00 00 00 00 1F 00
status: 0x2 (CHECK CONDITION)
Sense Bytes: 70 00 04 00 00 00 00 0A 00 00 00 00 08 03 00 00
Sense Key: 0x4 Hardware Error, Segment 0
Sense Code: 0x08 Qual 0x03 (logical unit communication crc error 
(ultra-dma/32)) Fru 0x0
Sense flags: Blk 0 (not valid) 
cmd finished after 0.312s timeout 200s
/usr/bin/wodim: A write error occured.
/usr/bin/wodim: Please properly read the error message above.
write track data: error after 0 bytes
Writing  time:   18.354s
Average write speed 180.7x.
Fixating...
Fixating time:   18.417s
BURN-Free was never needed.
/usr/bin/wodim: fifo had 64 puts and 1 gets.
/usr/bin/wodim: fifo was 0 times empty and 0 times full, min fill was 100%.

cdrecord command:
-----------------------
/usr/bin/wodim -v gracetime=2 dev=/dev/sr0 speed=48 -dao 
driveropts=burnfree -eject -data -tsize=83494s - 

--

This happens with K3B and with XCDRoast.


[Date Prev][Date Next]   [Thread Prev][Thread Next]   [Thread Index] [Date Index] [Author Index]