[Date Prev][Date Next]   [Thread Prev][Thread Next]   [Thread Index] [Date Index] [Author Index]

[Fedora-ia64-list] Re: Why do you set xen's driver "m"?



>On Fri, 2006-08-04 at 13:36 +0900, Akio Takebe wrote:
>> Hi, Juan
>> 
>> Thank you for your comments.
>> I can boot domU with the following modprobe.conf.
>> >	alias scsi_hostadapter xenblk
>> 
>> But I have some ide errors.
>> After I add extra = 'ide0=noprobe ide1=noprobe ide2=noprobe ide3=noprobe 
>> ide4=noprobe' into domU's config, ide errors are not occurred.
>
>I don't get them.  Could you post a log, and I will add that ide line to
>the kernel rpm :p
>
>Later, Juan.
Hi, Juan

The below is the boot log w/o ideX=noprobe.

[root tiger111 linux-2.6-xen-fedora.0802]# xm create /xen/conf/domU.conf -c
Using config file "/xen/conf/domU.conf".
Started domain paravm1
Dentry cache hash table entries: 65536 (order: 5, 524288 bytes)
Inode-cache hash table entries: 32768 (order: 4, 262144 bytes) 
Software IO TLB disabled                                      
Memory: 240640k/393216k available (5832k code, 152368k reserved, 4032k data, 272k init)
McKinley Errata 9 workaround not needed; disabling it                                  
register RESCHEDULE_VECTOR (RESCHED0) to xen irq (256)
register IPI_VECTOR (IPI0) to xen irq (257)           
Percpu irq 238 is unsupported by xen!      
register VIRQ_ITC (timer0) to xen irq (258)
Security Framework v1.0.0 initialized      
SELinux:  Initializing.              
SELinux:  Starting in permissive mode
selinux_register_security:  Registering secondary module capability
Capability LSM initialized as secondary                            
Mount-cache hash table entries: 1024   
ACPI: Core revision 20060707        
Boot processor id 0x0/0x0   
SMP mode deactivated.    
Brought up 1 CPUs    
Total of 1 processors activated (2236.41 BogoMIPS).
migration_cost=0                                   
checking if image is initramfs... it is
Freeing initrd memory: 6416kB freed    
DMI not present or invalid.        
grant table at e000010000000000
Grant table initialized        
NET: Registered protocol family 16
ACPI: bus type pci registered     
Brought up 1 CPUs            
ACPI: SCI (ACPI GSI 0) not registered
ACPI: Interpreter enabled            
ACPI: Using IOSAPIC for interrupt routing
Linux Plug and Play Support v0.97 (c) Adam Belay
pnp: PnP ACPI init                              
pnp: PnP ACPI: found 0 devices
xen_mem: Initialising balloon driver.
usbcore: registered new driver usbfs 
usbcore: registered new driver hub  
NET: Registered protocol family 2 
IP route cache hash table entries: 4096 (order: 1, 32768 bytes)
TCP established hash table entries: 16384 (order: 5, 524288 bytes)
TCP bind hash table entries: 8192 (order: 4, 262144 bytes)        
TCP: Hash tables configured (established 16384 bind 8192) 
TCP reno registered                                      
perfmon: version 2.0 IRQ 238
perfmon: Itanium 2 PMU detected, 16 PMCs, 18 PMDs, 4 counters (47 bits)
PAL Information Facility v0.5                                          
perfmon: added sampling format default_format
perfmon_default_smpl: default_format v2.0 registered
audit: initializing netlink socket (disabled)       
audit(1154659468.196:1): initialized         
VFS: Disk quotas dquot_6.5.1        
Dquot-cache hash table entries: 2048 (order 0, 16384 bytes)
SELinux:  Registering netfilter hooks                      
Initializing Cryptographic API       
io scheduler noop registered  
io scheduler anticipatory registered
io scheduler deadline registered    
io scheduler cfq registered (default)
ACPI Exception (acpi_processor-0681): AE_NOT_FOUND, Processor Device is not present [20060707]
ACPI: Getting cpuindex for acpiid 0x1                                                         
ACPI Exception (acpi_processor-0681): AE_NOT_FOUND, Processor Device is not present [20060707]
ACPI: Getting cpuindex for acpiid 0x2                                                         
EFI Time Services Driver v0.4        
Linux agpgart interface v0.101 (c) Dave Jones
RAMDISK driver initialized: 16 RAM disks of 16384K size 4096 blocksize
Xen virtual console successfully installed as tty1                    
Event-channel device installed.                   
Uniform Multi-Platform E-IDE driver Revision: 7.00alpha2
ide: Assuming 50MHz system bus speed for PIO modes; override with idebus=xx
hda: probing with STATUS(0xa1) instead of ALTSTATUS(0x08)                  
hda: IRQ probe failed (0xfffffffffffffffe)               
hda: probing with STATUS(0xa1) instead of ALTSTATUS(0x08)
hda: IRQ probe failed (0xfffffffffffffffe)               
hda: no response (status = 0xa1), resetting drive
hda: IRQ probe failed (0xfffffffffffffffe)       
hdb: probing with STATUS(0xa1) instead of ALTSTATUS(0x08)
hdb: IRQ probe failed (0xfffffffffffffffe)               
hdb: probing with STATUS(0xa1) instead of ALTSTATUS(0x08)
hdb: IRQ probe failed (0xfffffffffffffffe)               
hdb: no response (status = 0xa1), resetting drive
hdb: IRQ probe failed (0xfffffffffffffffe)       
hdc: probing with STATUS(0xa1) instead of ALTSTATUS(0x08)
hdc: IRQ probe failed (0xfffffffffffffffe)               
hdc: probing with STATUS(0xa1) instead of ALTSTATUS(0x08)
hdc: IRQ probe failed (0xfffffffffffffffe)               
hdc: no response (status = 0xa1), resetting drive
hdc: IRQ probe failed (0xfffffffffffffffe)       
hdd: probing with STATUS(0xa1) instead of ALTSTATUS(0x08)
hdd: IRQ probe failed (0xfffffffffffffffe)               
hdd: probing with STATUS(0xa1) instead of ALTSTATUS(0x08)
hdd: IRQ probe failed (0xfffffffffffffffe)               
hdd: no response (status = 0xa1), resetting drive
hdd: IRQ probe failed (0xfffffffffffffffe)       
hde: probing with STATUS(0xa1) instead of ALTSTATUS(0x08)
hde: IRQ probe failed (0xfffffffffffffffe)               
hde: probing with STATUS(0xa1) instead of ALTSTATUS(0x08)
hde: IRQ probe failed (0xfffffffffffffffe)               
hde: no response (status = 0xa1), resetting drive
hde: IRQ probe failed (0xfffffffffffffffe)       
hdf: probing with STATUS(0xa1) instead of ALTSTATUS(0x08)
hdf: IRQ probe failed (0xfffffffffffffffe)               
hdf: probing with STATUS(0xa1) instead of ALTSTATUS(0x08)
hdf: IRQ probe failed (0xfffffffffffffffe)               
hdf: no response (status = 0xa1), resetting drive
hdf: IRQ probe failed (0xfffffffffffffffe)       
hdg: probing with STATUS(0xa1) instead of ALTSTATUS(0x08)
hdg: IRQ probe failed (0xfffffffffffffffe)               
hdg: probing with STATUS(0xa1) instead of ALTSTATUS(0x08)
hdg: IRQ probe failed (0xfffffffffffffffe)               
hdg: no response (status = 0xa1), resetting drive
hdg: IRQ probe failed (0xfffffffffffffffe)       
hdh: probing with STATUS(0xa1) instead of ALTSTATUS(0x08)
hdh: IRQ probe failed (0xfffffffffffffffe)               
hdh: probing with STATUS(0xa1) instead of ALTSTATUS(0x08)
hdh: IRQ probe failed (0xfffffffffffffffe)               
hdh: no response (status = 0xa1), resetting drive
hdh: IRQ probe failed (0xfffffffffffffffe)       
ide-floppy driver 0.99.newide             
usbcore: registered new driver libusual
usbcore: registered new driver hiddev  
usbcore: registered new driver usbhid
drivers/usb/input/hid-core.c: v2.6:USB HID core driver
mice: PS/2 mouse device common for all mice           
md: md driver 0.90.3 MAX_MD_DEVS=256, MD_SB_DISKS=27
md: bitmap version 4.39                             
EFI Variables Facility v0.08 2004-May-17
efivars: get_next_variable: status=8000000000000003
TCP bic registered                                 
Initializing IPsec netlink socket
NET: Registered protocol family 1
NET: Registered protocol family 17
xen privcmd uses pseudo physical addr range [0x20000000, 0x3fffc000000] (4193728MB)
XENBUS: Device with no driver: device/vbd/2049                                     
Freeing unused kernel memory: 272kB freed     
Red Hat nash version 5.0.46 starting     
Mounting proc filesystem
Mounting sysfs filesystem
Creating /dev
Creating initial device nodes
Setting up hotplug.
Creating block device nodes.
Loading xenblk.ko module
Loading jbd.ko module
Registering block device major 8
Loading ext3.ko module          
Loading scsi_mod.ko module
SCSI subsystem initialized
Loading sd_mod.ko module  
register_blkdev: cannot get major 8 for sd
Loading scsi_transport_spi.ko module      
Loading mptbase.ko module
Fusion MPT base driver 3.04.01
Copyright (c) 1999-2005 LSI Logic Corporation
Loading mptscsih.ko module                   
Loading mptspi.ko module
Fusion MPT SPI Host driver 3.04.01
Creating root device.             
Mounting root filesystem.
kjournald starting.  Commit interval 5 seconds
EXT3-fs: mounted filesystem with ordered data mode.
Setting up other filesystems.                      
Setting up new root fs
no fstab.sys, mounting internal defaults
Switching to new root and running init.
unmounting old /dev
unmounting old /proc
unmounting old /proc/bus/usb
ERROR unmounting old /proc/bus/usb: No such file or directory
forcing unmount of /proc/bus/usb
unmounting old /sys
modprobe: FATAL: Could not load /lib/modules/2.6.18-rc3/modules.dep: No such file or directory

modprobe: FATAL: Could not load /lib/modules/2.6.18-rc3/modules.dep: No such file or directory

INIT: version 2.86 booting
                Welcome to Fedora Core
                Press 'I' to enter interactive startup.
Cannot access the Hardware Clock via any known method.
Use the --debug option to see the details of our search for an access method.
Setting clock  (localtime): Fri Aug  4 11:48:20 JST 2006 [  OK  ]
Starting udev: [  OK  ]
Setting hostname tiger156:  [  OK  ]
Checking filesystems
Checking all file systems.
[/sbin/fsck.ext3 (1) -- /] fsck.ext3 -a /dev/sda1 
/dev/sda1: clean, 80372/524288 files, 586652/1048576 blocks
[  OK  ]
Remounting root filesystem in read-write mode:  [  OK  ]
Mounting local filesystems:  [  OK  ]
Enabling local filesystem quotas:  [  OK  ]
Enabling /etc/fstab swaps:  [  OK  ]
INIT: Entering runlevel: 3
Entering non-interactive startup
Starting readahead_early:  Starting background readahead: [  OK  ]
[  OK  ]
Checking for hardware changes [  OK  ]
FATAL: Could not load /lib/modules/2.6.18-rc3/modules.dep: No such file or directory
CRITICAL : [ipv6_test] Kernel is not compiled with IPv6 support
Bringing up loopback interface:  [  OK  ]
Bringing up interface eth0:  Device eth0 does not seem to be present, delaying initialization.
[FAILED]
FATAL: Could not load /lib/modules/2.6.18-rc3/modules.dep: No such file or directory
CRITICAL : [ipv6_test] Kernel is not compiled with IPv6 support
Starting restorecond: [  OK  ]
Starting system logger: [  OK  ]
Starting kernel logger: [  OK  ]
Starting irqbalance: [  OK  ]
Starting portmap: [  OK  ]
Starting RPC idmapd: FATAL: Could not load /lib/modules/2.6.18-rc3/modules.dep: No such file or directory
Starting system message bus: [  OK  ]
Can't open RFCOMM control socket: Address family not supported by protocol

Starting hidd: Can't open HIDP control socket: Address family not supported by protocol
[FAILED]
Loading autofs4: [FAILED]
Starting smartd: [  OK  ]
Starting acpi daemon: [  OK  ]
Starting cups: [  OK  ]
Starting sshd: [  OK  ]
Starting vsftpd for vsftpd: [  OK  ]
Starting console mouse services: O0o.oops(): [console.c(83)]: Opening console failed.
[FAILED]
Starting crond: [  OK  ]
Starting xfs: [  OK  ]
Starting VNC server: no displays configured [  OK  ]
Starting anacron: [  OK  ]
Starting atd: [  OK  ]
Starting Avahi daemon: [  OK  ]
Starting HAL daemon: hald(1060): unaligned access to 0x60000fffff08761c, ip=0x2000000000506670
hald(1060): unaligned access to 0x60000fffff08761c, ip=0x2000000000506561                     
[  OK  ]                                                                 

Fedora Core release 5.90 (Test)
Kernel 2.6.18-rc3 on an ia64

tiger156 login:


Best Regards,

Akio Takebe


[Date Prev][Date Next]   [Thread Prev][Thread Next]   [Thread Index] [Date Index] [Author Index]