Help on routing table

[Craig White]

On Sun, 2006-04-02 at 16:33 +0200, Roger Grosswiler wrote:
> Am Sonntag, den 02.04.2006, 16:13 +0200 schrieb antonio montagnani:
> > I have a server with eth0 (192.168.0.1) and eth1(192.168.254.1) and I
> > connect by an Ethernet modem (192.168.254.254) by PPoE by eth1.
> > 
> > I get these information from ifconfig and route -n
> > sbin/ifconfig
> > eth0      Link encap:Ethernet  HWaddr 00:11:D8:BF:9F:05
> >           inet addr:192.168.0.1  Bcast:192.168.0.255  Mask:255.255.255.0
> >           inet6 addr: fe80::211:d8ff:febf:9f05/64 Scope:Link
> >           UP BROADCAST RUNNING MULTICAST  MTU:1500  Metric:1
> >           RX packets:0 errors:0 dropped:0 overruns:0 frame:0
> >           TX packets:72 errors:0 dropped:0 overruns:0 carrier:0
> >           collisions:0 txqueuelen:1000
> >           RX bytes:0 (0.0 b)  TX bytes:9676 (9.4 KiB)
> >           Interrupt:21
> > 
> > eth1      Link encap:Ethernet  HWaddr 52:54:05:E5:82:46
> >           inet addr:192.168.254.1  Bcast:192.168.254.255  Mask:255.255.255.0
> >           inet6 addr: fe80::5054:5ff:fee5:8246/64 Scope:Link
> >           UP BROADCAST RUNNING MULTICAST  MTU:1500  Metric:1
> >           RX packets:888 errors:0 dropped:0 overruns:0 frame:0
> >           TX packets:934 errors:0 dropped:0 overruns:0 carrier:0
> >           collisions:0 txqueuelen:1000
> >           RX bytes:429031 (418.9 KiB)  TX bytes:129154 (126.1 KiB)
> >           Interrupt:21 Base address:0xec00
> > 
> > lo        Link encap:Local Loopback
> >           inet addr:127.0.0.1  Mask:255.0.0.0
> >           inet6 addr: ::1/128 Scope:Host
> >           UP LOOPBACK RUNNING  MTU:16436  Metric:1
> >           RX packets:3806 errors:0 dropped:0 overruns:0 frame:0
> >           TX packets:3806 errors:0 dropped:0 overruns:0 carrier:0
> >           collisions:0 txqueuelen:0
> >           RX bytes:6875583 (6.5 MiB)  TX bytes:6875583 (6.5 MiB)
> > 
> > ppp0      Link encap:Point-to-Point Protocol
> >           inet addr:87.9.158.250  P-t-P:192.168.100.1  Mask:255.255.255.255
> >           UP POINTOPOINT RUNNING NOARP MULTICAST  MTU:1492  Metric:1
> >           RX packets:847 errors:0 dropped:0 overruns:0 frame:0
> >           TX packets:819 errors:0 dropped:0 overruns:0 carrier:0
> >           collisions:0 txqueuelen:3
> >           RX bytes:407494 (397.9 KiB)  TX bytes:99093 (96.7 KiB)
> >  /sbin/route -n
> > Kernel IP routing table
> > Destination     Gateway         Genmask         Flags Metric Ref    Use Iface
> > 192.168.100.1   0.0.0.0         255.255.255.255 UH    0      0        0 ppp0
> > 192.168.0.0     0.0.0.0         255.255.255.0   U     0      0        0 eth0
> > 192.168.254.0   0.0.0.0         255.255.255.0   U     0      0        0 eth1
> > 169.254.0.0     0.0.0.0         255.255.0.0     U     0      0        0 eth1
> > 0.0.0.0         192.168.100.1   0.0.0.0         UG    0      0        0 ppp0
> > 
> > 
> > Is it correct?? Why a double entry for eth1??
> > Tnx for help
> > --
> > Antonio Montagnani
> > Skype : antoniomontag
> > 
> 
> 169.254.0.0 is the private range for ip-adresses windoze uses by
> default :-D
----
it's not about Windows, it's about zeroconf

http://www.zeroconf.org/

if you want to disable it, see the note about zeroconf here...

http://www.redhat.com/magazine/010aug05/departments/tips_tricks/

Craig