2.6.22-41 and bcm43xx
Jesus Jr M Salvo
jesus.m.salvo at gmail.com
Sun Aug 12 02:45:21 UTC 2007
On 12/08/07, Jesus Jr M Salvo <jesus.m.salvo at gmail.com> wrote:
> With the new kernel ( 2.6.22.1-41 x86_64 ), I started getting these
> error messages during bootup ( which I did not receive in previous
> kernels such as 2.6.21-1.3228:
>
> bcm43xx-phy0 debug: Adding Interface type 2
> ssb: Switching to PCI-E core, index 3
> ssb: Switching to IEEE 802.11 core, index 1
> bcm43xx-phy0 debug: Loading firmware version 371.1061 (2006-10-04 21:02:04)
> ssb: Switching to ChipCommon core, index 0
> ssb: Switching to IEEE 802.11 core, index 1
> bcm43xx-phy0 debug: Radio turned on
> bcm43xx-phy0 debug: Radio enabled by hardware
> bcm43xx-phy0 debug: bbatt(11) >= size of LO array
>
> Call Trace:
> [<ffffffff881f2abf>] :bcm43xx_mac80211:bcm43xx_get_lo_g_ctl+0x65/0xa8
> [<ffffffff881f2b38>] :bcm43xx_mac80211:bcm43xx_lo_g_ctl_current+0x36/0x3b
> [<ffffffff881f2c1c>] :bcm43xx_mac80211:bcm43xx_lo_g_adjust+0x9/0x15
> [<ffffffff881ed25f>] :bcm43xx_mac80211:bcm43xx_phy_init_pctl+0x338/0x6a6
> [<ffffffff881e7af4>] :bcm43xx_mac80211:bcm43xx_phy_read+0x5c/0x63
> [<ffffffff881f052c>] :bcm43xx_mac80211:bcm43xx_phy_initg+0xc85/0xd0a
> [<ffffffff881f0d5f>] :bcm43xx_mac80211:bcm43xx_phy_init+0x582/0x5a7
> [<ffffffff881e4cce>] :bcm43xx_mac80211:bcm43xx_chip_init+0x68c/0x9a3
> [<ffffffff881e526d>] :bcm43xx_mac80211:bcm43xx_wireless_core_init+0x288/0x73e
> [<ffffffff881e62bb>] :bcm43xx_mac80211:bcm43xx_add_interface+0x5f/0xf4
> [<ffffffff881b16e4>] :mac80211:ieee80211_open+0x21d/0x34d
> [<ffffffff8124354d>] wext_handle_ioctl+0x354/0x39d
> [<ffffffff811df4af>] dev_open+0x2f/0x6e
> [<ffffffff811dd677>] dev_change_flags+0x5a/0x118
> [<ffffffff8122180f>] devinet_ioctl+0x235/0x597
> [<ffffffff8124adde>] do_page_fault+0x476/0x7b4
> [<ffffffff811d3053>] sock_ioctl+0x1c8/0x1e5
> [<ffffffff8109e807>] do_ioctl+0x2b/0xb6
> [<ffffffff8109ead5>] vfs_ioctl+0x243/0x25c
> [<ffffffff8109eb47>] sys_ioctl+0x59/0x7a
> [<ffffffff81009cd5>] tracesys+0xd5/0xda
>
> bcm43xx-phy0 debug: Chip initialized
> bcm43xx-phy0 debug: 32-bit DMA initialized
> bcm43xx-phy0 debug: Wireless interface started
> ADDRCONF(NETDEV_UP): wlan0: link is not ready
>
>
> Any ideas ?
>
Forgot to mention my actual card. From lspci -vv:
03:00.0 Network controller: Broadcom Corporation BCM4310 UART (rev 01)
Subsystem: Hewlett-Packard Company Unknown device 1361
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop-
ParErr- Stepping- SERR+ FastB2B-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
Latency: 0, Cache Line Size: 64 bytes
Interrupt: pin A routed to IRQ 19
Region 0: Memory at b3200000 (32-bit, non-prefetchable) [size=16K]
Capabilities: [40] Power Management version 2
Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=375mA
PME(D0-,D1-,D2-,D3hot-,D3cold-)
Status: D0 PME-Enable- DSel=0 DScale=2 PME-
Capabilities: [58] Message Signalled Interrupts: Mask- 64bit-
Queue=0/0 Enable-
Address: 00000000 Data: 0000
Capabilities: [d0] Express Legacy Endpoint IRQ 0
Device: Supported: MaxPayload 128 bytes, PhantFunc 0, ExtTag+
Device: Latency L0s <4us, L1 unlimited
Device: AtnBtn- AtnInd- PwrInd-
Device: Errors: Correctable- Non-Fatal- Fatal- Unsupported-
Device: RlxdOrd- ExtTag- PhantFunc- AuxPwr- NoSnoop-
Device: MaxPayload 128 bytes, MaxReadReq 128 bytes
Link: Supported Speed 2.5Gb/s, Width x1, ASPM L0s, Port 0
Link: Latency L0s <4us, L1 <64us
Link: ASPM Disabled RCB 64 bytes CommClk- ExtSynch-
Link: Speed 2.5Gb/s, Width x1
Capabilities: [100] Advanced Error Reporting
Capabilities: [13c] Virtual Channel
More information about the fedora-list
mailing list