[Date Prev][Date Next]   [Thread Prev][Thread Next]   [Thread Index] [Date Index] [Author Index]

Re: Adaptec 29160 Ultra160 problem -- Fedora 9 install.



>--- On Tue, 9/30/08, gary artim <gartim gmail com> wrote:
>
>> From: gary artim <gartim gmail com>
>> Subject: Adaptec 29160 Ultra160 problem -- Fedora 9 install.
>> To: fedora-list redhat com
>> Date: Tuesday, September 30, 2008, 12:49 AM
>> Hi --
>>
>> Installed fc9 on a server from fc8 and had a scsi
>> controller Adaptec
>> 29160 Ultra160 SCSI adapter
>> give me grief. It's used with an lto autochanger. When
>> I entered:
>>
>> mtx -d /dev/changer status
>> (/dev/changer a symlink to /dev/sg6)
>>
>> It hung for a while, (a huge listing follows, sorry about
>> this), then
>> kernel messages gallor.
>>
>> Anyway I tried  reseating the card, moving the card to an
>> alternate
>> slot, checking the cabling, reboot the autochanger,
>> reboot the system  --all did _not_ help.
>>
>> I pulled the card and replaced it with a Adaptec AIC-7892A
>> U160/m (rev
>> 02)  and the autochanger and lto drive worked.
>> I also had to swap cables because of the interface
>> differences.
>>
>> Long story, but can anyone say that this card looks broken?
>> It has a 5
>> year warranty and would like to get it replaced if so. Or
>> is
>> it a driver issue/I couldn't find a direct hit
>> searching the web or in
>> the archives?
>>
>> I think my head is still sore from banging it against the
>> autochanger!
>> Thanks for _any_ help!
>>
>> -- Gary
>>
>> Sep 27 10:30:15 genepi1 kernel: scsi5 : Adaptec AIC79XX
>> PCI-X SCSI HBA
>> DRIVER, Rev 3.0
>> Sep 27 10:30:15 genepi1 kernel:        <Adaptec 29320ALP
>> PCIx Ultra320
>> SCSI adapter>
>> Sep 27 10:30:15 genepi1 kernel:        aic7901: Ultra320
>> Wide Channel
>> A, SCSI Id=7, PCI-X 101-133Mhz, 512 SCBs
>> Sep 27 10:30:15 genepi1 kernel: ACPI: PCI Interrupt
>> 0000:04:01.0[A] ->
>> GSI 16 (level, low) -> IRQ 16
>> Sep 27 10:30:15 genepi1 kernel: e1000: 0000:04:01.0:
>> e1000_probe:
>> (PCI:66MHz:32-bit) 00:0e:0c:d9:8d:54
>> Sep 27 10:30:15 genepi1 kernel: scsi 5:0:1:0:
>> Sequential-Access HP
>>   Ultrium 4-SCSI   B12H PQ: 0 ANSI: 5
>> Sep 27 10:30:15 genepi1 kernel: scsi target5:0:1:
>> asynchronous
>> Sep 27 10:30:15 genepi1 kernel: scsi5:A:1:0: Tagged Queuing
>> enabled.  Depth 4
>> Sep 27 10:30:15 genepi1 kernel: scsi target5:0:1: Beginning
>> Domain Validation
>> Sep 27 10:30:15 genepi1 kernel: scsi target5:0:1: wide
>> asynchronous
>> Sep 27 10:30:15 genepi1 kernel: scsi target5:0:1: FAST-160
>> WIDE SCSI
>> 320.0 MB/s DT IU RTI PCOMP (6.25 ns, offset 64)
>> Sep 27 10:30:15 genepi1 kernel: scsi target5:0:1: Domain
>> Validation
>> skipping write tests
>> Sep 27 10:30:15 genepi1 kernel: scsi target5:0:1: Ending
>> Domain Validation
>> Sep 27 10:30:15 genepi1 kernel: scsi 5:0:1:1: Medium
>> Changer
>> OVERLAND NEO Series       0504 PQ: 0 ANSI: 5
>> Sep 27 10:30:15 genepi1 kernel: scsi5:A:1:1: Tagged Queuing
>> enabled.  Depth 4
>> Sep 27 10:30:15 genepi1 kernel: e1000: eth2: e1000_probe:
>> Intel(R)
>> PRO/1000 Network Connection
>> Sep 27 10:30:15 genepi1 kernel: device-mapper: uevent:
>> version 1.0.3
>> Sep 27 10:30:15 genepi1 kernel: device-mapper: ioctl:
>> 4.13.0-ioctl
>> (2007-10-18) initialised: dm-devel redhat com
>> Sep 27 10:30:15 genepi1 kernel: device-mapper: multipath:
>> version 1.0.5 loaded
>> Sep 27 10:30:15 genepi1 kernel: EXT3 FS on sda1, internal
>> journal
>> Sep 27 10:30:15 genepi1 kernel: Adding 25165812k swap on
>> /dev/sda2.
>> Priority:-1 extents:1 across:25165812k
>> Sep 27 10:30:15 genepi1 kernel: firmware: requesting
>> intel-ucode/06-0f-06
>> Sep 27 10:30:15 genepi1 kernel: firmware: requesting
>> intel-ucode/06-0f-06
>> Sep 27 10:30:15 genepi1 kernel: firmware: requesting
>> intel-ucode/06-0f-06
>> Sep 27 10:30:15 genepi1 kernel: firmware: requesting
>> intel-ucode/06-0f-06
>> Sep 27 10:30:15 genepi1 kernel: IA-32 Microcode Update
>> Driver: v1.14a
>> <tigran aivazian fsnet co uk>
>> Sep 27 10:30:15 genepi1 kernel: microcode: CPU0 updated
>> from revision
>> 0x44 to 0xcd, date = 09162007
>> Sep 27 10:30:15 genepi1 kernel: microcode: CPU1 updated
>> from revision
>> 0x44 to 0xcd, date = 09162007
>> Sep 27 10:30:15 genepi1 kernel: microcode: CPU2 updated
>> from revision
>> 0x44 to 0xcd, date = 09162007
>> Sep 27 10:30:15 genepi1 kernel: microcode: CPU3 updated
>> from revision
>> 0x44 to 0xcd, date = 09162007
>> Sep 27 10:30:15 genepi1 kernel: scsi 5:0:1:0: Attached scsi
>> generic sg5 type 1
>> Sep 27 10:30:15 genepi1 kernel: scsi 5:0:1:1: Attached scsi
>> generic sg6 type 8
>> Sep 27 10:30:15 genepi1 kernel: osst :I: Tape driver with
>> OnStream
>> support version 0.99.4
>> Sep 27 10:30:15 genepi1 kernel: osst :I: $Id: osst.c,v 1.73
>> 2005/01/01
>> 21:13:34 wriede Exp $
>> Sep 27 10:30:15 genepi1 kernel: Driver 'osst' needs
>> updating - please
>> use bus_type methods
>> Sep 27 10:30:15 genepi1 kernel: st: Version 20080224, fixed
>> bufsize
>> 32768, s/g segs 256
>> Sep 27 10:30:15 genepi1 kernel: Driver 'st' needs
>> updating - please
>> use bus_type methods
>> Sep 27 10:30:15 genepi1 kernel: st 5:0:1:0: Attached scsi
>> tape st0
>> Sep 27 10:30:15 genepi1 kernel: st 5:0:1:0: st0: try direct
>> i/o: yes
>> (alignment 4 B)
>> Sep 27 10:30:15 genepi1 kernel: eth0: Link is Up 1000 Mbps
>> Full
>> Duplex, Flow Control: RX
>> Sep 27 10:30:15 genepi1 kernel: ADDRCONF(NETDEV_CHANGE):
>> eth0: link
>> becomes ready
>> Sep 27 10:30:15 genepi1 kernel: ADDRCONF(NETDEV_UP): eth1:
>> link is not ready
>> Sep 27 10:54:58 genepi1 yum: Installed:
>> mtx-1.3.12-1.fc9.x86_64
>> Sep 27 10:58:19 genepi1 kernel: 3w-9xxx: scsi4: ERROR:
>> (0x03:0x010D):
>> Invalid field in CDB:.
>> Sep 27 10:58:19 genepi1 kernel: 3w-9xxx: scsi4: ERROR:
>> (0x03:0x0101):
>> Invalid command opcode:opcode=0xB8.
>> Sep 27 10:58:19 genepi1 kernel: 3w-9xxx: scsi4: ERROR:
>> (0x03:0x0101):
>> Invalid command opcode:opcode=0xB8.
>> Sep 27 11:02:27 genepi1 kernel: st 5:0:1:0: Attempting to
>> queue an
>> ABORT message:CDB: 0x12 0x0 0x0 0x0 0x38 0x0
>> Sep 27 11:02:27 genepi1 kernel: scsi5: At time of recovery,
>> card was not paused
>> Sep 27 11:02:27 genepi1 kernel:
>> >>>>>>>>>>>>>>>>>>
>> Dump Card State
>> Begins
>> <<<<<<<<<<<<<<<<<
>> Sep 27 11:02:27 genepi1 kernel: scsi5: Dumping Card State
>> at program
>> address 0x34 Mode 0x22
>> Sep 27 11:02:27 genepi1 kernel: Card was paused
>> Sep 27 11:02:27 genepi1Sep 27 11:02:27 genepi1 kernel:
>> INTSTAT[0x0]
>> SELOID[0x1] SELID[0x10] HS_MAILBOX[0x0]
>> Sep 27 11:02:27 genepi1 kernel: INTCTL[0x80]
>> SEQINTSTAT[0x0]
>> SAVED_MODE[0x11] DFFSTAT[0x33]
>> Sep 27 11:02:27 genepi1 kernel: SCSISIGI[0x0]
>> SCSIPHASE[0x0]
>> SCSIBUS[0x0] LASTPHASE[0x1]
>> Sep 27 11:02:27 genepi1 kernel: SCSISEQ0[0x0]
>> SCSISEQ1[0x12]
>> SEQCTL0[0x0] SEQINTCTL[0x0]
>> Sep 27 11:02:27 genepi1 kernel: SEQ_FLAGS[0x0]
>> SEQ_FLAGS2[0x4]
>> QFREEZE_COUNT[0x7]
>> Sep 27 11:02:27 genepi1 kernel: KERNEL_QFREEZE_COUNT[0x6]
>> MK_MESSAGE_SCB[0xff00]
>> Sep 27 11:02:27 genepi1 kernel: MK_MESSAGE_SCSIID[0xff]
>> SSTAT0[0x0] SSTAT1[0x8]
>> Sep 27 11:02:27 genepi1 kernel: SSTAT2[0x0] SSTAT3[0x0]
>> PERRDIAG[0x0]
>> SIMODE1[0xa4]
>> Sep 27 11:02:27 genepi1 kernel: LQISTAT0[0x0] LQISTAT1[0x0]
>> LQISTAT2[0x0] LQOSTAT0[0x0]
>> Sep 27 11:02:27 genepi1 kernel: LQOSTAT1[0x0]
>> LQOSTAT2[0xe1]
>> Sep 27 11:02:27 genepi1 kernel:
>> Sep 27 11:02:27 genepi1 kernel: SCB Count = 4 CMDS_PENDING
>> = 0 LASTSCB
>> 0xffff CURRSCB 0x3 NEXTSCB 0xff80
>> Sep 27 11:02:27 genepi1 kernel: qinstart = 44 qinfifonext =
>> 46
>> Sep 27 11:02:27 genepi1 kernel: QINFIFO: 0x3 0x2
>> Sep 27 11:02:27 genepi1 kernel: WAITING_TID_QUEUES:
>> Sep 27 11:02:27 genepi1 kernel: Pending list:
>> Sep 27 11:02:27 genepi1 kernel:  2 FIFO_USE[0x0]
>> SCB_CONTROL[0x68]
>> SCB_SCSIID[0x17]
>> Sep 27 11:02:27 genepi1 kernel:  3 FIFO_USE[0x2]
>> SCB_CONTROL[0x68]
>> SCB_SCSIID[0x17]
>> Sep 27 11:02:27 genepi1 kernel: Total 2
>> Sep 27 11:02:27 genepi1 kernel: Kernel Free SCB list: 1 0
>> Sep 27 11:02:27 genepi1 kernel: Sequencer Complete
>> DMA-inprog list:
>> Sep 27 11:02:27 genepi1 kernel: Sequencer Complete list:
>> Sep 27 11:02:27 genepi1 kernel: Sequencer DMA-Up and
>> Complete list:
>> Sep 27 11:02:27 genepi1 kernel: Sequencer On QFreeze and
>> Complete list:
>> Sep 27 11:02:27 genepi1 kernel:
>> Sep 27 11:02:27 genepi1 kernel:
>> Sep 27 11:02:27 genepi1 kernel: scsi5: FIFO0 Free, LONGJMP
>> == 0x82a3, SCB 0x3
>> Sep 27 11:02:27 genepi1 kernel: SEQIMODE[0x3f]
>> SEQINTSRC[0x0]
>> DFCNTRL[0x0] DFSTATUS[0x89]
>> Sep 27 11:02:27 genepi1 kernel: SG_CACHE_SHADOW[0x2]
>> SG_STATE[0x0]
>> DFFSXFRCTL[0x0]
>> Sep 27 11:02:27 genepi1 kernel: SOFFCNT[0x0] MDFFSTAT[0x5]
>> SHADDR =
>> 0x00, SHCNT = 0x0
>> Sep 27 11:02:27 genepi1 kernel: HADDR = 0x00, HCNT = 0x0
>> CCSGCTL[0x10]
>> Sep 27 11:02:27 genepi1 kernel:
>> Sep 27 11:02:27 genepi1 kernel: scsi5: FIFO1 Free, LONGJMP
>> == 0x8063, SCB 0x3
>> Sep 27 11:02:27 genepi1 kernel: SEQIMODE[0x3f]
>> SEQINTSRC[0x0]
>> DFCNTRL[0x0] DFSTATUS[0x89]
>> Sep 27 11:02:27 genepi1 kernel: SG_CACHE_SHADOW[0x2]
>> SG_STATE[0x0]
>> DFFSXFRCTL[0x0]
>> Sep 27 11:02:27 genepi1 kernel: SOFFCNT[0x0] MDFFSTAT[0x5]
>> SHADDR =
>> 0x00, SHCNT = 0x0
>> Sep 27 11:02:27 genepi1 kernel: HADDR = 0x00, HCNT = 0x0
>> CCSGCTL[0x10]
>> Sep 27 11:02:27 genepi1 kernel: LQIN: 0x8 0x0 0x0 0x3 0x0
>> 0x1 0x0 0x0
>> 0x0 0x0 0x0 0x0 0x0 0x0 0x0 0x0 0x0 0x0 0x0 0x0
>> Sep 27 11:02:27 genepi1 kernel: scsi5: LQISTATE = 0x0,
>> LQOSTATE = 0x0,
>> OPTIONMODE = 0x52
>> Sep 27 11:02:27 genepi1 kernel: scsi5: OS_SPACE_CNT = 0x20
>> MAXCMDCNT = 0x1
>> Sep 27 11:02:27 genepi1 kernel: scsi5: SAVED_SCSIID = 0x0
>> SAVED_LUN = 0x0
>> Sep 27 11:02:27 genepi1 kernel: SIMODE0[0xc]
>> Sep 27 11:02:27 genepi1 kernel: CCSCBCTL[0x0]
>> Sep 27 11:02:27 genepi1 kernel: scsi5: REG0 == 0x3, SINDEX
>> = 0x104,
>> DINDEX = 0x104
>> Sep 27 11:02:27 genepi1 kernel: scsi5: SCBPTR == 0x3,
>> SCB_NEXT ==
>> 0xff80, SCB_NEXT2 == 0xff80
>> Sep 27 11:02:27 genepi1 kernel: CDB 3 0 0 83 a 8c
>> Sep 27 11:02:27 genepi1 kernel: STACK: 0x20 0x0 0x0 0x0 0x0
>> 0x0 0x0 0x0
>> Sep 27 11:02:27 genepi1 kernel:
>> <<<<<<<<<<<<<<<<<
>> Dump Card State Ends
>> >>>>>>>>>>>>>>>>>>
>> Sep 27 11:02:27 genepi1 kernel: scsi5:0:1:0: Cmd aborted
>> from QINFIFO
>> Sep 27 11:02:37 genepi1 kernel: st 5:0:1:0: Attempting to
>> queue an
>> ABORT message:CDB: 0x0 0x0 0x0 0x0 0x0 0x0
>> Sep 27 11:02:37 genepi1 kernel: scsi5: At time of recovery,
>> card was not paused
>> Sep 27 11:02:37 genepi1 kernel:
>> >>>>>>>>>>>>>>>>>>
>> Dump Card State
>> Begins
>> <<<<<<<<<<<<<<<<<
>> Sep 27 11:02:37 genepi1 kernel: scsi5: Dumping Card State
>> at program
>> address 0x18 Mode 0x33
>>  kernel: INTSTAT[0x0] SELOID[0x1] SELID[0x10]
>> HS_MAILBOX[0x0]
>> Sep 27 11:02:27 genepi1 kernel: INTCTL[0x80]
>> SEQINTSTAT[0x0]
>> SAVED_MODE[0x11] DFFSTAT[0x33]
>> Sep 27 11:02:37 genepi1 kernel:
>> >>>>>>>>>>>>>>>>>>
>> Dump Card State
>> Begins
>> <<<<<<<<<<<<<<<<<
>> Sep 27 11:02:37 genepi1 kernel: scsi5: Dumping Card State
>> at program
>> address 0x18 Mode 0x33
>> Sep 27 11:02:37 genepi1 kernel: Card was paused
>> Sep 27 11:02:37 genepi1 kernel: INTSTAT[0x0] SELOID[0x1]
>> SELID[0x10]
>> HS_MAILBOX[0x0]
>> Sep 27 11:02:37 genepi1 kernel: INTCTL[0x80]
>> SEQINTSTAT[0x0]
>> SAVED_MODE[0x11] DFFSTAT[0x33]
>> Sep 27 11:02:37 genepi1 kernel: SCSISIGI[0x0]
>> SCSIPHASE[0x0]
>> SCSIBUS[0x0] LASTPHASE[0x1]
>> Sep 27 11:02:37 genepi1 kernel: SCSISEQ0[0x0]
>> SCSISEQ1[0x12]
>> SEQCTL0[0x0] SEQINTCTL[0x0]
>> Sep 27 11:02:37 genepi1 kernel: SEQ_FLAGS[0x0]
>> SEQ_FLAGS2[0x4]
>> QFREEZE_COUNT[0x7]
>> Sep 27 11:02:37 genepi1 kernel: KERNEL_QFREEZE_COUNT[0x6]
>> MK_MESSAGE_SCB[0xff00]
>> Sep 27 11:02:37 genepi1 kernel: MK_MESSAGE_SCSIID[0xff]
>> SSTAT0[0x0] SSTAT1[0x0]
>> Sep 27 11:02:37 genepi1 kernel: SSTAT2[0x0] SSTAT3[0x0]
>> PERRDIAG[0x0]
>> SIMODE1[0xa4]
>> Sep 27 11:02:37 genepi1 kernel: LQISTAT0[0x0] LQISTAT1[0x0]
>> LQISTAT2[0x0] LQOSTAT0[0x0]
>> Sep 27 11:02:37 genepi1 kernel: LQOSTAT1[0x0]
>> LQOSTAT2[0xe1]
>> Sep 27 11:02:37 genepi1 kernel:
>> Sep 27 11:02:37 genepi1 kernel: SCB Count = 4 CMDS_PENDING
>> = 0 LASTSCB
>> 0xffff CURRSCB 0x3 NEXTSCB 0xff80
>> Sep 27 11:02:37 genepi1 kernel: qinstart = 44 qinfifonext =
>> 46
>> Sep 27 11:02:37 genepi1 kernel: QINFIFO: 0x3 0x2
>> Sep 27 11:02:37 genepi1 kernel: WAITING_TID_QUEUES:
>> Sep 27 11:02:37 genepi1 kernel: Pending list:
>> Sep 27 11:02:37 genepi1 kernel:  2 FIFO_USE[0x0]
>> SCB_CONTROL[0x68]
>> SCB_SCSIID[0x17]
>> Sep 27 11:02:37 genepi1 kernel:  3 FIFO_USE[0x2]
>> SCB_CONTROL[0x68]
>> SCB_SCSIID[0x17]
>> Sep 27 11:02:37 genepi1 kernel: Total 2
>> Sep 27 11:02:37 genepi1 kernel: Kernel Free SCB list: 1 0
>> Sep 27 11:02:37 genepi1 kernel: Sequencer Complete
>> DMA-inprog list:
>> Sep 27 11:02:37 genepi1 kernel: Sequencer Complete list:
>> Sep 27 11:02:37 genepi1 kernel: Sequencer DMA-Up and
>> Complete list:
>> Sep 27 11:02:37 genepi1 kernel: Sequencer On QFreeze and
>> Complete list:
>> Sep 27 11:02:37 genepi1 kernel:
>> Sep 27 11:02:37 genepi1 kernel:
>> Sep 27 11:02:37 genepi1 kernel: scsi5: FIFO0 Free, LONGJMP
>> == 0x82a3, SCB 0x3
>> Sep 27 11:02:37 genepi1 kernel: SEQIMODE[0x3f]
>> SEQINTSRC[0x0]
>> DFCNTRL[0x0] DFSTATUS[0x89]
>> Sep 27 11:02:37 genepi1 kernel: SG_CACHE_SHADOW[0x2]
>> SG_STATE[0x0]
>> DFFSXFRCTL[0x0]
>> Sep 27 11:02:37 genepi1 kernel: SOFFCNT[0x0] MDFFSTAT[0x5]
>> SHADDR =
>> 0x00, SHCNT = 0x0
>> Sep 27 11:02:37 genepi1 kernel: HADDR = 0x00, HCNT = 0x0
>> CCSGCTL[0x10]
>> Sep 27 11:02:37 genepi1 kernel:
>> Sep 27 11:02:37 genepi1 kernel: scsi5: FIFO1 Free, LONGJMP
>> == 0x8063, SCB 0x3
>> Sep 27 11:02:37 genepi1 kernel: SEQIMODE[0x3f]
>> SEQINTSRC[0x0]
>> DFCNTRL[0x0] DFSTATUS[0x89]
>> Sep 27 11:02:37 genepi1 kernel: SG_CACHE_SHADOW[0x2]
>> SG_STATE[0x0]
>> DFFSXFRCTL[0x0]
>> Sep 27 11:02:37 genepi1 kernel: SOFFCNT[0x0] MDFFSTAT[0x5]
>> SHADDR =
>> 0x00, SHCNT = 0x0
>> Sep 27 11:02:37 genepi1 kernel: HADDR = 0x00, HCNT = 0x0
>> CCSGCTL[0x10]
>> Sep 27 11:02:37 genepi1 kernel: LQIN: 0x8 0x0 0x0 0x3 0x0
>> 0x1 0x0 0x0
>> 0x0 0x0 0x0 0x0 0x0 0x0 0x0 0x0 0x0 0x0 0x0 0x0
>> Sep 27 11:02:37 genepi1 kernel: scsi5: LQISTATE = 0x0,
>> LQOSTATE = 0x0,
>> OPTIONMODE = 0x52
>> Sep 27 11:02:37 genepi1 kernel: scsi5: OS_SPACE_CNT = 0x20
>> MAXCMDCNT = 0x1
>> Sep 27 11:02:37 genepi1 kernel: scsi5: SAVED_SCSIID = 0x0
>> SAVED_LUN = 0x0
>> Sep 27 11:02:37 genepi1 kernel: SIMODE0[0xc]
>> Sep 27 11:02:37 genepi1 kernel: CCSCBCTL[0x0]
>> Sep 27 11:02:37 genepi1 kernel: scsi5: REG0 == 0xffff,
>> SINDEX = 0x104,
>> DINDEX = 0x104
>> Sep 27 11:02:37 genepi1 kernel: scsi5: SCBPTR == 0x3,
>> SCB_NEXT ==
>> 0xff80, SCB_NEXT2 == 0xff80
>> Sep 27 11:02:37 genepi1 kernel: CDB 3 0 0 83 a 8c
>> Sep 27 11:02:37 genepi1 kernel: STACK: 0x0 0x0 0x0 0x0 0x0
>> 0x0 0x0 0x0
>> Sep 27 11:02:37 Sep 27 11:02:37 genepi1 kernel:
>> scsi5:0:1:0: Cmd
>> aborted from QINFIFO
>> Sep 27 11:02:37 genepi1 kernel: scsi 5:0:1:1: Attempting to
>> queue an
>> ABORT message:CDB: 0x1a 0x8 0x1d 0x0 0x88 0x0
>> Sep 27 11:02:37 genepi1 kernel: scsi5: At time of recovery,
>> card was not paused
>> Sep 27 11:02:37 genepi1 kernel:
>> >>>>>>>>>>>>>>>>>>
>> Dump Card State
>> Begins
>> <<<<<<<<<<<<<<<<<
>> Sep 27 11:02:37 genepi1 kernel: scsi5: Dumping Card State
>> at program
>> address 0x31 Mode 0x11
>> Sep 27 11:02:37 genepi1 kernel: Card was paused
>> Sep 27 11:02:37 genepi1 kernel: INTSTAT[0x0] SELOID[0x1]
>> SELID[0x10]
>> HS_MAILBOX[0x0]
>> Sep 27 11:02:37 genepi1 kernel: INTCTL[0x80]
>> SEQINTSTAT[0x0]
>> SAVED_MODE[0x11] DFFSTAT[0x33]
>> Sep 27 11:02:37 genepi1 kernel: SCSISIGI[0x0]
>> SCSIPHASE[0x0]
>> SCSIBUS[0x0] LASTPHASE[0x1]
>> Sep 27 11:02:37 genepi1 kernel: SCSISEQ0[0x0]
>> SCSISEQ1[0x12]
>> SEQCTL0[0x0] SEQINTCTL[0x0]
>> Sep 27 11:02:37 genepi1 kernel: SEQ_FLAGS[0x0]
>> SEQ_FLAGS2[0x4]
>> QFREEZE_COUNT[0x7]
>> Sep 27 11:02:37 genepi1 kernel: KERNEL_QFREEZE_COUNT[0x6]
>> MK_MESSAGE_SCB[0xff00]
>> Sep 27 11:02:37 genepi1 kernel: MK_MESSAGE_SCSIID[0xff]
>> SSTAT0[0x0] SSTAT1[0x0]
>> Sep 27 11:02:37 genepi1 kernel: SSTAT2[0x0] SSTAT3[0x0]
>> PERRDIAG[0x0]
>> SIMODE1[0xa4]
>> Sep 27 11:02:37 genepi1 kernel: LQISTAT0[0x0] LQISTAT1[0x0]
>> LQISTAT2[0x0] LQOSTAT0[0x0]
>> Sep 27 11:02:37 genepi1 kernel: LQOSTAT1[0x0]
>> LQOSTAT2[0xe1]
>> Sep 27 11:02:37 genepi1 kernel:
>> Sep 27 11:02:37 genepi1 kernel: SCB Count = 4 CMDS_PENDING
>> = 0 LASTSCB
>> 0xffff CURRSCB 0x3 NEXTSCB 0xff80
>> Sep 27 11:02:37 genepi1 kernel: qinstart = 44 qinfifonext =
>> 45
>> Sep 27 11:02:37 genepi1 kernel: QINFIFO: 0x3
>> Sep 27 11:02:37 genepi1 kernel: WAITING_TID_QUEUES:
>> Sep 27 11:02:37 genepi1 kernel: Pending list:
>> Sep 27 11:02:37 genepi1 kernel:  3 FIFO_USE[0x0]
>> SCB_CONTROL[0x68]
>> SCB_SCSIID[0x17]
>> Sep 27 11:02:37 genepi1 kernel: Total 1
>> Sep 27 11:02:37 genepi1 kernel: Kernel Free SCB list: 2 1 0
>> Sep 27 11:02:37 genepi1 kernel: Sequencer Complete
>> DMA-inprog list:
>> Sep 27 11:02:37 genepi1 kernel: Sequencer Complete list:
>> Sep 27 11:02:37 genepi1 kernel: Sequencer DMA-Up and
>> Complete list:
>> Sep 27 11:02:37 genepi1 kernel: Sequencer On QFreeze and
>> Complete list:
>> Sep 27 11:02:37 genepi1 kernel:
>> Sep 27 11:02:37 genepi1 kernel:
>> Sep 27 11:02:37 genepi1 kernel: scsi5: FIFO0 Free, LONGJMP
>> == 0x82a3, SCB 0x3
>> Sep 27 11:02:37 genepi1 kernel: SEQIMODE[0x3f]
>> SEQINTSRC[0x0]
>> DFCNTRL[0x0] DFSTATUS[0x89]
>> Sep 27 11:02:37 genepi1 kernel: SG_CACHE_SHADOW[0x2]
>> SG_STATE[0x0]
>> DFFSXFRCTL[0x0]
>> Sep 27 11:02:37 genepi1 kernel: SOFFCNT[0x0] MDFFSTAT[0x5]
>> SHADDR =
>> 0x00, SHCNT = 0x0
>> Sep 27 11:02:37 genepi1 kernel: HADDR = 0x00, HCNT = 0x0
>> CCSGCTL[0x10]
>> Sep 27 11:02:37 genepi1 kernel:
>> Sep 27 11:02:37 genepi1 kernel: scsi5: FIFO1 Free, LONGJMP
>> == 0x8063, SCB 0x3
>> Sep 27 11:02:37 genepi1 kernel: SEQIMODE[0x3f]
>> SEQINTSRC[0x0]
>> DFCNTRL[0x0] DFSTATUS[0x89]
>> Sep 27 11:02:37 genepi1 kernel: SG_CACHE_SHADOW[0x2]
>> SG_STATE[0x0]
>> DFFSXFRCTL[0x0]
>> Sep 27 11:02:37 genepi1 kernel: SOFFCNT[0x0] MDFFSTAT[0x5]
>> SHADDR =
>> 0x00, SHCNT = 0x0
>> Sep 27 11:02:37 genepi1 kernel: HADDR = 0x00, HCNT = 0x0
>> CCSGCTL[0x10]
>> Sep 27 11:02:37 genepi1 kernel: LQIN: 0x8 0x0 0x0 0x3 0x0
>> 0x1 0x0 0x0
>> 0x0 0x0 0x0 0x0 0x0 0x0 0x0 0x0 0x0 0x0 0x0 0x0
>> Sep 27 11:02:37 genepi1 kernel: scsi5: LQISTATE = 0x0,
>> LQOSTATE = 0x0,
>> OPTIONMODE = 0x52
>> Sep 27 11:02:37 genepi1 kernel: scsi5: OS_SPACE_CNT = 0x20
>> MAXCMDCNT = 0x1
>> Sep 27 11:02:37 genepi1 kernel: scsi5: SAVED_SCSIID = 0x0
>> SAVED_LUN = 0x0
>> Sep 27 11:02:37 genepi1 kernel: SIMODE0[0xc]
>> Sep 27 11:02:37 genepi1 kernel: CCSCBCTL[0x0]
>> Sep 27 11:02:37 genepi1 kernel: scsi5: REG0 == 0x3, SINDEX
>> = 0x104,
>> DINDEX = 0x104
>> Sep 27 11:02:37 genepi1 kernel: scsi5: SCBPTR == 0x3,
>> SCB_NEXT ==
>> 0xff80, SCB_NEXT2 == 0xff80
>> Sep 27 11:02:37 genepi1 kernel: CDB 3 0 0 83 a 8c
>> Sep 27 11:02:37 genepi1 kernel: STACK: 0x1f 0x0 0x0 0x0 0x0
>> 0x0 0x0 0x0
>> Sep 27 11:02:37 genepi1 kernel:
>> <<<<<<<<<<<<<<<<<
>> Dump Card State Ends
>> >>>>>>>>>>>>>>>>>>
>> genepi1 kernel:
>> <<<<<<<<<<<<<<<<<
>> Dump Card State Ends
>> >>>>>>>>>>>>>>>>>>
>> Sep 27 11:02:37 genepi1 kernel: scsi5:0:1:0: Cmd aborted
>> from QINFIFO
>> Sep 27 11:02:37 genepi1 kernel: scsi 5:0:1:1: Attempting to
>> queue an
>> ABORT message:CDB: 0x1a 0x8 0x1d 0x0 0x88 0x0
>> Sep 27 11:02:37 genepi1 kernel: scsi5:0:1:0: Cmd aborted
>> from QINFIFO
>> Sep 27 11:02:37 genepi1 kernel: scsi 5:0:1:1: Attempting to
>> queue an
>> ABORT message:CDB: 0x1a 0x8 0x1d 0x0 0x88 0x0
>> Sep 27 11:02:37 genepi1 kernel: scsi5: At time of recovery,
>> card was not paused
>> Sep 27 11:02:37 genepi1 kernel:
>> >>>>>>>>>>>>>>>>>>
>> Dump Card State
>> Begins
>> <<<<<<<<<<<<<<<<<
>> Sep 27 11:02:37 genepi1 kernel: scsi5: Dumping Card State
>> at program
>> address 0x31 Mode 0x11
>> Sep 27 11:02:37 genepi1 kernel: Card was paused
>> Sep 27 11:02:37 genepi1 kernel: INTSTAT[0x0] SELOID[0x1]
>> SELID[0x10]
>> HS_MAILBOX[0x0]
>> Sep 27 11:02:37 genepi1 kernel: INTCTL[0x80]
>> SEQINTSTAT[0x0]
>> SAVED_MODE[0x11] DFFSTAT[0x33]
>> Sep 27 11:02:37 genepi1 kernel: SCSISIGI[0x0]
>> SCSIPHASE[0x0]
>> SCSIBUS[0x0] LASTPHASE[0x1]
>> Sep 27 11:02:37 genepi1 kernel: SCSISEQ0[0x0]
>> SCSISEQ1[0x12]
>> SEQCTL0[0x0] SEQINTCTL[0x0]
>> Sep 27 11:02:37 genepi1 kernel: SEQ_FLAGS[0x0]
>> SEQ_FLAGS2[0x4]
>> QFREEZE_COUNT[0x7]
>> Sep 27 11:02:37 genepi1 kernel: KERNEL_QFREEZE_COUNT[0x6]
>> MK_MESSAGE_SCB[0xff00]
>> Sep 27 11:02:37 genepi1 kernel: MK_MESSAGE_SCSIID[0xff]
>> SSTAT0[0x0] SSTAT1[0x0]
>> Sep 27 11:02:37 genepi1 kernel: SSTAT2[0x0] SSTAT3[0x0]
>> PERRDIAG[0x0]
>> SIMODE1[0xa4]
>> Sep 27 11:02:37 genepi1 kernel: LQISTAT0[0x0] LQISTAT1[0x0]
>> LQISTAT2[0x0] LQOSTAT0[0x0]
>> Sep 27 11:02:37 genepi1 kernel: LQOSTAT1[0x0]
>> LQOSTAT2[0xe1]
>> Sep 27 11:02:37 genepi1 kernel:
>> Sep 27 11:02:37 genepi1 kernel: SCB Count = 4 CMDS_PENDING
>> = 0 LASTSCB
>> 0xffff CURRSCB 0x3 NEXTSCB 0xff80
>> Sep 27 11:02:37 genepi1 kernel: qinstart = 44 qinfifonext =
>> 45
>> Sep 27 11:02:37 genepi1 kernel: QINFIFO: 0x3
>> Sep 27 11:02:37 genepi1 kernel: WAITING_TID_QUEUES:
>> Sep 27 11:02:37 genepi1 kernel: Pending list:
>> Sep 27 11:02:37 genepi1 kernel:  3 FIFO_USE[0x0]
>> SCB_CONTROL[0x68]
>> SCB_SCSIID[0x17]
>> Sep 27 11:02:37 genepi1 kernel: Total 1
>> Sep 27 11:02:37 genepi1 kernel: Kernel Free SCB list: 2 1 0
>> Sep 27 11:02:37 genepi1 kernel: Sequencer Complete
>> DMA-inprog list:
>> Sep 27 11:02:37 genepi1 kernel: Sequencer Complete list:
>> Sep 27 11:02:37 genepi1 kernel: Sequencer DMA-Up and
>> Complete list:
>> Sep 27 11:02:37 genepi1 kernel: Sequencer On QFreeze and
>> Complete list:
>> Sep 27 11:02:37 genepi1 kernel:
>> Sep 27 11:02:37 genepi1 kernel:
>> Sep 27 11:02:37 genepi1 kernel: scsi5: FIFO0 Free, LONGJMP
>> == 0x82a3, SCB 0x3
>> Sep 27 11:02:37 genepi1 kernel: SEQIMODE[0x3f]
>> SEQINTSRC[0x0]
>> DFCNTRL[0x0] DFSTATUS[0x89]
>> Sep 27 11:02:37 genepi1 kernel: SG_CACHE_SHADOW[0x2]
>> SG_STATE[0x0]
>> DFFSXFRCTL[0x0]
>> Sep 27 11:02:37 genepi1 kernel: SOFFCNT[0x0] MDFFSTAT[0x5]
>> SHADDR =
>> 0x00, SHCNT = 0x0
>> Sep 27 11:02:37 genepi1 kernel: HADDR = 0x00, HCNT = 0x0
>> CCSGCTL[0x10]
>> Sep 27 11:02:37 genepi1 kernel:
>> Sep 27 11:02:37 genepi1 kernel: scsi5: FIFO1 Free, LONGJMP
>> == 0x8063, SCB 0x3
>> Sep 27 11:02:37 genepi1 kernel: SEQIMODE[0x3f]
>> SEQINTSRC[0x0]
>> DFCNTRL[0x0] DFSTATUS[0x89]
>> Sep 27 11:02:37 genepi1 kernel: SG_CACHE_SHADOW[0x2]
>> SG_STATE[0x0]
>> DFFSXFRCTL[0x0]
>> Sep 27 11:02:37 genepi1 kernel: SOFFCNT[0x0] MDFFSTAT[0x5]
>> SHADDR =
>> 0x00, SHCNT = 0x0
>> Sep 27 11:02:37 genepi1 kernel: HADDR = 0x00, HCNT = 0x0
>> CCSGCTL[0x10]
>> Sep 27 11:02:37 genepi1 kernel: LQIN: 0x8 0x0 0x0 0x3 0x0
>> 0x1 0x0 0x0
>> 0x0 0x0 0x0 0x0 0x0 0x0 0x0 0x0 0x0 0x0 0x0 0x0
>> Sep 27 11:02:37 genepi1 kernel: scsi5: LQISTATE = 0x0,
>> LQOSTATE = 0x0,
>> OPTIONMODE = 0x52
>> Sep 27 11:02:37 genepi1 kernel: scsi5: OS_SPACE_CNT = 0x20
>> MAXCMDCNT = 0x1
>> Sep 27 11:02:37 genepi1 kernel: scsi5: SAVED_SCSIID = 0x0
>> SAVED_LUN = 0x0
>> Sep 27 11:02:37 genepi1 kernel: SIMODE0[0xc]
>> Sep 27 11:02:37 genepi1 kernel: CCSCBCTL[0x0]
>> Sep 27 11:02:37 genepi1 kernel: scsi5: REG0 == 0x3, SINDEX
>> = 0x104,
>> DINDEX = 0x104
>> Sep 27 11:02:37 genepi1 kernel: scsi5: SCBPTR == 0x3,
>> SCB_NEXT ==
>> 0xff80, SCB_NEXT2 == 0xff80
>> Sep 27 11:02:37 genepi1 kernel: CDB 3 0 0 83 a 8c
>> Sep 27 11:02:37 genepi1 kernel: STACK: 0x1f 0x0 0x0 0x0 0x0
>> 0x0 0x0 0x0
>> Sep 27 11:02:37 genepi1 kernel:
>> <<<<<<<<<<<<<<<<<
>> Dump Card State Ends
>> >>>>>>>>>>>>>>>>>>
>> Sep 27 11:02:37 genepi1 kernel: STACK: 0x1f 0x0 0x0 0x0 0x0
>> 0x0 0x0 0x0
>> Sep 27 11:02:37 genepi1 kernel:
>> <<<<<<<<<<<<<<<<<
>> Dump Card State Ends
>> >>>>>>>>>>>>>>>>>>
>> Sep 27 11:02:37 genepi1 kernel: scsi5:0:1:1: Cmd aborted
>> from QINFIFO
>> Sep 27 11:02:47 genepi1 kernel: scsi 5:0:1:1: Attempting to
>> queue an
>> ABORT message:CDB: 0x0 0x0 0x0 0x0 0x0 0x0
>> Sep 27 11:02:47 genepi1 kernel: scsi5: At time of recovery,
>> card was not paused
>> Sep 27 11:02:47 genepi1 kernel:
>> >>>>>>>>>>>>>>>>>>
>> Dump Card State
>> Begins
>> <<<<<<<<<<<<<<<<<
>> Sep 27 11:02:47 genepi1 kernel: scsi5: Dumping Card State
>> at program
>> address 0x18 Mode 0x33
>> Sep 27 11:02:47 genepi1 kernel: Card was paused
>> Sep 27 11:02:47 genepi1 kernel: INTSTAT[0x0] SELOID[0x1]
>> SELID[0x10]
>> HS_MAILBOX[0x0]
>> Sep 27 11:02:47 genepi1 kernel: INTCTL[0x80]
>> SEQINTSTAT[0x0]
>> SAVED_MODE[0x11] DFFSTAT[0x33]
>> Sep 27 11:02:47 genepi1 kernel: SCSISIGI[0x0]
>> SCSIPHASE[0x0]
>> SCSIBUS[0x0] LASTPHASE[0x1]
>> Sep 27 11:02:47 genepi1 kernel: SCSISEQ0[0x0]
>> SCSISEQ1[0x12]
>> SEQCTL0[0x0] SEQINTCTL[0x0]
>> Sep 27 11:02:47 genepi1 kernel: SEQ_FLAGS[0x0]
>> SEQ_FLAGS2[0x4]
>> QFREEZE_COUNT[0x7]
>> Sep 27 11:02:47 genepi1 kernel: KERNEL_QFREEZE_COUNT[0x6]
>> MK_MESSAGE_SCB[0xff00]
>> Sep 27 11:02:47 genepi1 kernel: MK_MESSAGE_SCSIID[0xff]
>> SSTAT0[0x0] SSTAT1[0x0]
>> Sep 27 11:02:47 genepi1 kernel: SSTAT2[0x0] SSTAT3[0x0]
>> PERRDIAG[0x0]
>> SIMODE1[0xa4]
>> Sep 27 11:02:47 genepi1 kernel: LQISTAT0[0x0] LQISTAT1[0x0]
>> LQISTAT2[0x0] LQOSTAT0[0x0]
>> Sep 27 11:02:47 genepi1 kernel: LQOSTAT1[0x0]
>> LQOSTAT2[0xe1]
>> Sep 27 11:02:47 genepi1 kernel:
>> Sep 27 11:02:47 genepi1 kernel: SCB Count = 4 CMDS_PENDING
>> = 0 LASTSCB
>> 0xffff CURRSCB 0x3 NEXTSCB 0xff80
>> Sep 27 11:02:47 genepi1 kernel: qinstart = 44 qinfifonext =
>> 45
>> Sep 27 11:02:47 genepi1 kernel: QINFIFO: 0x3
>> Sep 27 11:02:47 genepi1 kernel: WAITING_TID_QUEUES:
>> Sep 27 11:02:47 genepi1 kernel: Pending list:
>> Sep 27 11:02:47 genepi1 kernel:  3 FIFO_USE[0x0]
>> SCB_CONTROL[0x68]
>> SCB_SCSIID[0x17]
>> Sep 27 11:02:47 genepi1 kernel: Total 1
>> Sep 27 11:02:47 genepi1 kernel: Kernel Free SCB list: 2 1 0
>> Sep 27 11:02:47 genepi1 kernel: Sequencer Complete
>> DMA-inprog list:
>> Sep 27 11:02:47 genepi1 kernel: Sequencer Complete list:
>> Sep 27 11:02:47 genepi1 kernel: Sequencer DMA-Up and
>> Complete list:
>> Sep 27 11:02:47 genepi1 kernel: Sequencer On QFreeze and
>> Complete list:
>> Sep 27 11:02:47 genepi1 kernel:
>> Sep 27 11:02:47 genepi1 kernel:
>> Sep 27 11:02:47 genepi1 kernel: scsi5: FIFO0 Free, LONGJMP
>> == 0x82a3, SCB 0x3
>> Sep 27 11:02:47 genepi1 kernel: SEQIMODE[0x3f]
>> SEQINTSRC[0x0]
>> DFCNTRL[0x0] DFSTATUS[0x89]
>> Sep 27 11:02:47 genepi1 kernel: SG_CACHE_SHADOW[0x2]
>> SG_STATE[0x0]
>> DFFSXFRCTL[0x0]
>> Sep 27 11:02:47 genepi1 kernel: SOFFCNT[0x0] MDFFSTAT[0x5]
>> SHADDR =
>> 0x00, SHCNT = 0x0
>> Sep 27 11:02:47 genepi1 kernel: HADDR = 0x00, HCNT = 0x0
>> CCSGCTL[0x10]
>> Sep 27 11:02:47 genepi1 kernel:
>> Sep 27 11:02:47 genepi1 kernel: scsi5: FIFO1 Free, LONGJMP
>> == 0x8063, SCB 0x3
>> Sep 27 11:02:47 genepi1 kernel: SEQIMODE[0x3f]
>> SEQINTSRC[0x0]
>> DFCNTRL[0x0] DFSTATUS[0x89]
>> Sep 27 11:02:47 genepi1 kernel: SG_CACHE_SHADOW[0x2]
>> SG_STATE[0x0]
>> DFFSXFRCTL[0x0]
>> Sep 27 11:02:47 genepi1 kernel: SOFFCNT[0x0] MDFFSTAT[0x5]
>> SHADDR =
>> 0x00, SHCNT = 0x0
>> Sep 27 11:02:47 genepi1 kernel: HADDR = 0x00, HCNT = 0x0
>> CCSGCTL[0x10]
>> Sep 27 11:02:47 genepi1 kernel: LQIN: 0x8 0x0 0x0 0x3 0x0
>> 0x1 0x0 0x0
>> 0x0 0x0 0x0 0x0 0x0 0x0 0x0 0x0 0x0 0x0 0x0 0x0
>> Sep 27 11:02:47 genepi1 kernel: scsi5: LQISTATE = 0x0,
>> LQOSTATE = 0x0,
>> OPTIONMODE = 0x52
>> Sep 27 11:02:47 genepi1 kernel: scsi5: OS_SPACE_CNT = 0x20
>> MAXCMDCNT = 0x1
>> Sep 27 11:02:47 genepi1 kernel: scsi5: SAVED_SCSIID = 0x0
>> SAVED_LUN = 0x0
>> Sep 27 11:02:47 genepi1 kernel: SIMODE0[0xc]
>> Sep 27 11:02:47 genepi1 kernel: CCSCBCTL[0x0]
>> Sep 27 11:02:47 genepi1 kernel: scsi5: REG0 == 0xffff,
>> SINDEX = 0x104,
>> DINDEX = 0x104
>> Sep 27 11:02:47 genepi1 kernel: scsi5: SCBPTR == 0x3,
>> SCB_NEXT ==
>> 0xff80, SCB_NEXT2 == 0xff80
>> Sep 27 11:02:47 genepi1 kernel: CDB 3 0 0 83 a 8c
>> Sep 27 11:02:47 genepi1 kernel: scsi5: SCBPTR == 0x3,
>> SCB_NEXT ==
>> 0xff80, SCB_NEXT2 == 0xff80
>> Sep 27 11:02:47 genepi1 kernel: CDB 3 0 0 83 a 8c
>> Sep 27 11:02:47 genepi1 kernel: STACK: 0x0 0x0 0x0 0x0 0x0
>> 0x0 0x0 0x0
>> Sep 27 11:02:47 genepi1 kernel:
>> <<<<<<<<<<<<<<<<<
>> Dump Card State Ends
>> >>>>>>>>>>>>>>>>>>
>> Sep 27 11:02:47 genepi1 kernel: scsi5:0:1:1: Cmd aborted
>> from QINFIFO
>> Sep 27 11:02:47 genepi1 kernel: st 5:0:1:0: Attempting to
>> queue a
>> TARGET RESET message:CDB: 0x12 0x0 0x0 0x0 0x38 0x0
>> Sep 27 11:02:47 genepi1 kernel: scsi5: Device reset code
>> sleeping
>> Sep 27 11:02:52 genepi1 kernel: scsi5: Device reset timer
>> expired (active 1)
>> Sep 27 11:02:52 genepi1 kernel: scsi5: Device reset
>> returning 0x2003
>> Sep 27 11:02:52 genepi1 kernel: scsi 5:0:1:1: Attempting to
>> queue a
>> TARGET RESET message:CDB: 0x1a 0x8 0x1d 0x0 0x88 0x0
>> Sep 27 11:02:52 genepi1 kernel: scsi5: Device reset code
>> sleeping
>> Sep 27 11:02:57 genepi1 kernel: scsi5: Device reset timer
>> expired (active 1)
>> Sep 27 11:02:57 genepi1 kernel: scsi5: Device reset
>> returning 0x2003
>> Sep 27 11:02:57 genepi1 kernel: Recovery SCB completes
>> Sep 27 11:02:57 genepi1 kernel: Recovery SCB completes
>> Sep 27 11:03:17 genepi1 kernel: st 5:0:1:0: Attempting to
>> queue an
>> ABORT message:CDB: 0x0 0x0 0x0 0x0 0x0 0x0
>> Sep 27 11:03:17 genepi1 kernel: scsi5: At time of recovery,
>> card was not paused
>> Sep 27 11:03:17 genepi1 kernel:
>> >>>>>>>>>>>>>>>>>>
>> Dump Card State
>> Begins
>> <<<<<<<<<<<<<<<<<
>> Sep 27 11:03:17 genepi1 kernel: scsi5: Dumping Card State
>> at program
>> address 0x9 Mode 0x33
>> Sep 27 11:03:17 genepi1 kernel: Card was paused
>> Sep 27 11:03:17 genepi1 kernel: INTSTAT[0x0] SELOID[0x1]
>> SELID[0x10]
>> HS_MAILBOX[0x0]
>> Sep 27 11:03:17 genepi1 kernel: INTCTL[0x80]
>> SEQINTSTAT[0x0]
>> SAVED_MODE[0x11] DFFSTAT[0x33]
>> Sep 27 11:03:17 genepi1 kernel: SCSISIGI[0x0]
>> SCSIPHASE[0x0]
>> SCSIBUS[0x0] LASTPHASE[0x1]
>> Sep 27 11:03:17 genepi1 kernel: SCSISEQ0[0x0]
>> SCSISEQ1[0x12]
>> SEQCTL0[0x0] SEQINTCTL[0x0]
>> Sep 27 11:03:17 genepi1 kernel: SEQ_FLAGS[0x0]
>> SEQ_FLAGS2[0x4]
>> QFREEZE_COUNT[0x7]
>> Sep 27 11:03:17 genepi1 kernel: KERNEL_QFREEZE_COUNT[0x6]
>> MK_MESSAGE_SCB[0xff00]
>> Sep 27 11:03:17 genepi1 kernel: MK_MESSAGE_SCSIID[0xff]
>> SSTAT0[0x0] SSTAT1[0x0]
>> Sep 27 11:03:17 genepi1 kernel: SSTAT2[0x0] SSTAT3[0x0]
>> PERRDIAG[0x0]
>> SIMODE1[0xa4]
>> Sep 27 11:03:17 genepi1 kernel: LQISTAT0[0x0] LQISTAT1[0x0]
>> LQISTAT2[0x0] LQOSTAT0[0x0]
>> Sep 27 11:03:17 genepi1 kernel: LQOSTAT1[0x0]
>> LQOSTAT2[0xe1]
>> Sep 27 11:03:17 genepi1 kernel:
>> Sep 27 11:03:17 genepi1 kernel: SCB Count = 4 CMDS_PENDING
>> = 0 LASTSCB
>> 0xffff CURRSCB 0x3 NEXTSCB 0xff80
>> Sep 27 11:03:17 genepi1 kernel: qinstart = 44 qinfifonext =
>> 45
>> Sep 27 11:03:17 genepi1 kernel: QINFIFO: 0x2
>> Sep 27 11:03:17 genepi1 kernel: WAITING_TID_QUEUES:
>> Sep 27 11:03:17 genepi1 kernel: Pending list:
>> Sep 27 11:03:17 genepi1 kernel:  2 FIFO_USE[0x0]
>> SCB_CONTROL[0x68]
>> SCB_SCSIID[0x17]
>> Sep 27 11:03:17 genepi1 kernel: Total 1
>> Sep 27 11:03:17 genepi1 kernel: Kernel Free SCB list: 3 1 0
>> Sep 27 11:03:17 genepi1 kernel: Sequencer Complete
>> DMA-inprog list:
>> Sep 27 11:03:17 genepi1 kernel: Sequencer Complete list:
>> Sep 27 11:03:17 genepi1 kernel: Sequencer DMA-Up and
>> Complete list:
>> Sep 27 11:03:17 genepi1 kernel: Sequencer On QFreeze and
>> Complete list:
>> Sep 27 11:03:17 genepi1 kernel:
>> Sep 27 11:03:17 genepi1 kernel:
>> Sep 27 11:03:17 genepi1 kernel: scsi5: FIFO0 Free, LONGJMP
>> == 0x80a3, SCB 0x3
>> Sep 27 11:03:17 genepi1 kernel: SEQIMODE[0x3f]
>> SEQINTSRC[0x0]
>> DFCNTRL[0x0] DFSTATUS[0x89]
>> Sep 27 11:03:17 genepi1 kernel: SG_CACHE_SHADOW[0x2]
>> SG_STATE[0x0]
>> DFFSXFRCTL[0x0]
>> Sep 27 11:03:17 genepi1 kernel: SOFFCNT[0x0] MDFFSTAT[0x5]
>> SHADDR =
>> 0x00, SHCNT = 0x0
>> Sep 27 11:03:17 genepi1 kernel: HADDR = 0x00, HCNT = 0x0
>> CCSGCTL[0x10]
>> Sep 27 11:03:17 genepi1 kernel:
>> Sep 27 11:03:17 genepi1 kernel: scsi5: FIFO1 Free, LONGJMP
>> == 0x8063, SCB 0x3
>> Sep 27 11:03:17 genepi1 kernel: SEQIMODE[0x3f]
>> SEQINTSRC[0x0]
>> DFCNTRL[0x0] DFSTATUS[0x89]
>> Sep 27 11:03:17 genepi1 kernel: scsi5: FIFO1 Free, LONGJMP
>> == 0x8063, SCB 0x3
>> Sep 27 11:03:17 genepi1 kernel: SEQIMODE[0x3f]
>> SEQINTSRC[0x0]
>> DFCNTRL[0x0] DFSTATUS[0x89]
>> Sep 27 11:03:17 genepi1 kernel: SG_CACHE_SHADOW[0x2]
>> SG_STATE[0x0]
>> DFFSXFRCTL[0x0]
>> Sep 27 11:03:17 genepi1 kernel: SOFFCNT[0x0] MDFFSTAT[0x5]
>> SHADDR =
>> 0x00, SHCNT = 0x0
>> Sep 27 11:03:17 genepi1 kernel: HADDR = 0x00, HCNT = 0x0
>> CCSGCTL[0x10]
>> Sep 27 11:03:17 genepi1 kernel: LQIN: 0x8 0x0 0x0 0x3 0x0
>> 0x1 0x0 0x0
>> 0x0 0x0 0x0 0x0 0x0 0x0 0x0 0x0 0x0 0x0 0x0 0x0
>> Sep 27 11:03:17 genepi1 kernel: scsi5: LQISTATE = 0x0,
>> LQOSTATE = 0x0,
>> OPTIONMODE = 0x52
>> Sep 27 11:03:17 genepi1 kernel: scsi5: OS_SPACE_CNT = 0x20
>> MAXCMDCNT = 0x1
>> Sep 27 11:03:17 genepi1 kernel: scsi5: SAVED_SCSIID = 0x0
>> SAVED_LUN = 0x0
>> Sep 27 11:03:17 genepi1 kernel: SIMODE0[0xc]
>> Sep 27 11:03:17 genepi1 kernel: CCSCBCTL[0x0]
>> Sep 27 11:03:17 genepi1 kernel: scsi5: REG0 == 0xffff,
>> SINDEX = 0x104,
>> DINDEX = 0x104
>> Sep 27 11:03:17 genepi1 kernel: scsi5: SCBPTR == 0x3,
>> SCB_NEXT ==
>> 0xff80, SCB_NEXT2 == 0xff80
>> Sep 27 11:03:17 genepi1 kernel: CDB 3 0 0 83 a 8c
>> Sep 27 11:03:17 genepi1 kernel: STACK: 0x0 0x0 0x0 0x0 0x0
>> 0x0 0x0 0x0
>> Sep 27 11:03:17 genepi1 kernel:
>> <<<<<<<<<<<<<<<<<
>> Dump Card State Ends
>> >>>>>>>>>>>>>>>>>>
>> Sep 27 11:03:17 genepi1 kernel: scsi5:0:1:0: Cmd aborted
>> from QINFIFO
>> Sep 27 11:03:27 genepi1 kernel: scsi 5:0:1:1: Attempting to
>> queue an
>> ABORT message:CDB: 0x0 0x0 0x0 0x0 0x0 0x0
>> Sep 27 11:03:27 genepi1 kernel: scsi5: At time of recovery,
>> card was not paused
>> Sep 27 11:03:27 genepi1 kernel:
>> >>>>>>>>>>>>>>>>>>
>> Dump Card State
>> Begins
>> <<<<<<<<<<<<<<<<<
>> Sep 27 11:03:27 genepi1 kernel: scsi5: Dumping Card State
>> at program
>> address 0x22 Mode 0x33
>> Sep 27 11:03:27 genepi1 kernel: Card was paused
>> Sep 27 11:03:27 genepi1 kernel: INTSTAT[0x0] SELOID[0x1]
>> SELID[0x10]
>> HS_MAILBOX[0x0]
>> Sep 27 11:03:27 genepi1 kernel: INTCTL[0x80]
>> SEQINTSTAT[0x0]
>> SAVED_MODE[0x11] DFFSTAT[0x33]
>> Sep 27 11:03:27 genepi1 kernel: SCSISIGI[0x0]
>> SCSIPHASE[0x0]
>> SCSIBUS[0x0] LASTPHASE[0x1]
>> Sep 27 11:03:27 genepi1 kernel: SCSISEQ0[0x0]
>> SCSISEQ1[0x12]
>> SEQCTL0[0x0] SEQINTCTL[0x0]
>> Sep 27 11:03:27 genepi1 kernel: SEQ_FLAGS[0x0]
>> SEQ_FLAGS2[0x4]
>> QFREEZE_COUNT[0x7]
>> Sep 27 11:03:27 genepi1 kernel: KERNEL_QFREEZE_COUNT[0x6]
>> MK_MESSAGE_SCB[0xff00]
>> Sep 27 11:03:27 genepi1 kernel: MK_MESSAGE_SCSIID[0xff]
>> SSTAT0[0x0] SSTAT1[0x0]
>> Sep 27 11:03:27 genepi1 kernel: SSTAT2[0x0] SSTAT3[0x0]
>> PERRDIAG[0x0]
>> SIMODE1[0xa4]
>> Sep 27 11:03:27 genepi1 kernel: LQISTAT0[0x0] LQISTAT1[0x0]
>> LQISTAT2[0x0] LQOSTAT0[0x0]
>> Sep 27 11:03:27 genepi1 kernel: LQOSTAT1[0x0]
>> LQOSTAT2[0xe1]
>> Sep 27 11:03:27 genepi1 kernel:
>> Sep 27 11:03:27 genepi1 kernel: SCB Count = 4 CMDS_PENDING
>> = 0 LASTSCB
>> 0xffff CURRSCB 0x3 NEXTSCB 0xff80
>> Sep 27 11:03:27 genepi1 kernel: qinstart = 44 qinfifonext =
>> 45
>> Sep 27 11:03:27 genepi1 kernel: QINFIFO: 0x2
>> Sep 27 11:03:27 genepi1 kernel: WAITING_TID_QUEUES:
>> Sep 27 11:03:27 genepi1 kernel: Pending list:
>> Sep 27 11:03:27 genepi1 kernel:  2 FIFO_USE[0x0]
>> SCB_CONTROL[0x68]
>> SCB_SCSIID[0x17]
>> Sep 27 11:03:27 genepi1 kernel: Total 1
>> Sep 27 11:03:27 genepi1 kernel: Kernel Free SCB list: 3 1 0
>> Sep 27 11:03:27 genepi1 kernel: Sequencer Complete
>> DMA-inprog list:
>> Sep 27 11:03:27 genepi1 kernel: Sequencer Complete list:
>> Sep 27 11:03:27 genepi1 kernel: Sequencer DMA-Up and
>> Complete list:
>> Sep 27 11:03:27 genepi1 kernel: Sequencer On QFreeze and
>> Complete list:
>> Sep 27 11:03:27 genepi1 kernel:
>> Sep 27 11:03:27 genepi1 kernel:
>> Sep 27 11:03:27 genepi1 kernel: scsi5: FIFO0 Free, LONGJMP
>> == 0x80a3, SCB 0x3
>> Sep 27 11:03:27 genepi1 kernel: SEQIMODE[0x3f]
>> SEQINTSRC[0x0]
>> DFCNTRL[0x0] DFSTATUS[0x89]
>> Sep 27 11:03:27 genepi1 kernel: SG_CACHE_SHADOW[0x2]
>> SG_STATE[0x0]
>> DFFSXFRCTL[0x0]
>> Sep 27 11:03:Sep 27 11:03:27 genepi1 kernel: HADDR = 0x00,
>> HCNT = 0x0
>> CCSGCTL[0x10]
>> Sep 27 11:03:27 genepi1 kernel:
>> Sep 27 11:03:27 genepi1 kernel: scsi5: FIFO1 Free, LONGJMP
>> == 0x8063, SCB 0x3
>> Sep 27 11:03:27 genepi1 kernel: SEQIMODE[0x3f]
>> SEQINTSRC[0x0]
>> DFCNTRL[0x0] DFSTATUS[0x89]
>> Sep 27 11:03:27 genepi1 kernel: SG_CACHE_SHADOW[0x2]
>> SG_STATE[0x0]
>> DFFSXFRCTL[0x0]
>> Sep 27 11:03:27 genepi1 kernel: SOFFCNT[0x0] MDFFSTAT[0x5]
>> SHADDR =
>> 0x00, SHCNT = 0x0
>> Sep 27 11:03:27 genepi1 kernel: HADDR = 0x00, HCNT = 0x0
>> CCSGCTL[0x10]
>> Sep 27 11:03:27 genepi1 kernel: LQIN: 0x8 0x0 0x0 0x3 0x0
>> 0x1 0x0 0x0
>> 0x0 0x0 0x0 0x0 0x0 0x0 0x0 0x0 0x0 0x0 0x0 0x0
>> Sep 27 11:03:27 genepi1 kernel: scsi5: LQISTATE = 0x0,
>> LQOSTATE = 0x0,
>> OPTIONMODE = 0x52
>> Sep 27 11:03:27 genepi1 kernel: scsi5: OS_SPACE_CNT = 0x20
>> MAXCMDCNT = 0x1
>> Sep 27 11:03:27 genepi1 kernel: scsi5: SAVED_SCSIID = 0x0
>> SAVED_LUN = 0x0
>> Sep 27 11:03:27 genepi1 kernel: SIMODE0[0xc]
>> Sep 27 11:03:27 genepi1 kernel: CCSCBCTL[0x0]
>> Sep 27 11:03:27 genepi1 kernel: scsi5: REG0 == 0xffff,
>> SINDEX = 0x104,
>> DINDEX = 0x104
>> Sep 27 11:03:27 genepi1 kernel: scsi5: SCBPTR == 0x3,
>> SCB_NEXT ==
>> 0xff80, SCB_NEXT2 == 0xff80
>> Sep 27 11:03:27 genepi1 kernel: CDB 3 0 0 83 a 8c
>> Sep 27 11:03:27 genepi1 kernel: STACK: 0x1e 0x0 0x0 0x0 0x0
>> 0x0 0x0 0x0
>> Sep 27 11:03:27 genepi1 kernel:
>> <<<<<<<<<<<<<<<<<
>> Dump Card State Ends
>> >>>>>>>>>>>>>>>>>>
>> Sep 27 11:03:27 genepi1 kernel: scsi5:0:1:1: Cmd aborted
>> from QINFIFO
>> Sep 27 11:03:27 genepi1 kernel: st 5:0:1:0: Device offlined
>> - not
>> ready after error recovery
>> Sep 27 11:03:27 genepi1 kernel: scsi 5:0:1:1: Device
>> offlined - not
>> ready after error recovery
>> Sep 27 11:07:00 genepi1 kernel: 3w-9xxx: scsi4: ERROR:
>> (0x03:0x010D):
>> Invalid field in CDB:.
>> Sep 27 11:07:00 genepi1 kernel: 3w-9xxx: scsi4: ERROR:
>> (0x03:0x0101):
>> Invalid command opcode:opcode=0xB8.
>> Sep 27 11:07:00 genepi1 kernel: 3w-9xxx: scsi4: ERROR:
>> (0x03:0x0101):
>> Invalid command opcode:opcode=0xB8.
>> Sep 27 11:16:41 genepi1 kernel: 3w-9xxx: scsi4: ERROR:
>> (0x03:0x010D):
>> Invalid field in CDB:.
>> Sep 27 11:16:41 genepi1 kernel: 3w-9xxx: scsi4: ERROR:
>> (0x03:0x0101):
>> Invalid command opcode:opcode=0xB8.
>> Sep 27 11:16:41 genepi1 kernel: 3w-9xxx: scsi4: ERROR:
>> (0x03:0x0101):
>> Invalid command opcode:opcode=0xB8.
>> Sep 27 11:16:51 genepi1 kernel: 3w-9xxx: scsi4: ERROR:
>> (0x03:0x010D):
>> Invalid field in CDB:.
>> Sep 27 11:16:51 genepi1 kernel: 3w-9xxx: scsi4: ERROR:
>> (0x03:0x0101):
>> Invalid command opcode:opcode=0xB8.
>> Sep 27 11:16:51 genepi1 kernel: 3w-9xxx: scsi4: ERROR:
>> (0x03:0x0101):
>> Invalid command opcode:opcode=0xB8.
>> 27 genepi1 kernel: SOFFCNT[0x0] MDFFSTAT[0x5] SHADDR =
>> 0x00, SHCNT = 0x0
>> Sep 27 11:03:27 genepi1 kernel: HADDR = 0x00, HCNT = 0x0
>> CCSGCTL[0x10]
>> Sep 27 11:03:27 genepi1 kernel:
>>
>My Adaptec 29160 Ultra160 comes with testing software shown early in boot!
>
>Next comes grub
>
Thanks, I'll try pursuing this, Gary


[Date Prev][Date Next]   [Thread Prev][Thread Next]   [Thread Index] [Date Index] [Author Index]