[Date Prev][Date Next]   [Thread Prev][Thread Next]   [Thread Index] [Date Index] [Author Index]

Re: Need help with Reboot cause



g> i do hope peter stieber is picking up on all this. :)

He is :-)

I loaded gnome-applet-sensors and was able to monitor the temperature on each of the two Opterons in the system. The were a little high. I also installed the hddtemp package. They were warm as well.

I moved the machine (it was in a corner without good air flow), took off the side panel, pointed a small room fan into the case. This significantly cooled off the CPUs and HDs, but I could still get the machine to reboot by running my build. After one reboot, just trying to startx (the machine starts at run level 3) caused a reboot.

I tried running sensors, but there were no drivers loaded, so I ran sensors-detect and answered yes to all of the defaults to get some sensor drivers loaded. Here is the current output from sensors...

k8temp-pci-00c3
Adapter: PCI adapter
Core0 Temp:  +39.0°C

k8temp-pci-00cb
Adapter: PCI adapter
Core0 Temp:  +38.0°C

adt7463-i2c-0-2e
Adapter: SMBus AMD8111 adapter at 10e0
V1.5:        +2.61 V  (min =  +0.00 V, max =  +3.32 V)
VCore:       +1.30 V  (min =  +0.00 V, max =  +2.99 V)
V3.3:        +3.36 V  (min =  +0.00 V, max =  +4.38 V)
V5:          +4.58 V  (min =  +0.00 V, max =  +6.64 V)
V12:        +11.95 V  (min =  +0.00 V, max = +15.94 V)
CPU_Fan:    1633 RPM  (min =    0 RPM)
fan2:          0 RPM  (min =    0 RPM)
fan3:       3321 RPM  (min =    0 RPM)
fan4:       3292 RPM  (min =    0 RPM)
CPU Temp:    +41.5°C  (low  = -127.0°C, high = +127.0°C)
Board Temp:  +34.2°C  (low  = -127.0°C, high = +127.0°C)
Remote Temp: +39.5°C  (low  = -127.0°C, high = +127.0°C)
cpu0_vid:   +1.500 V

w83627hf-isa-0290
Adapter: ISA adapter
VCore 1:     +1.52 V  (min =  +1.74 V, max =  +2.14 V)   ALARM
VCore 2:     +1.49 V  (min =  +1.74 V, max =  +2.14 V)   ALARM
+3.3V:       +3.22 V  (min =  +2.82 V, max =  +3.79 V)
+5V:         +4.46 V  (min =  +5.56 V, max =  +5.75 V)   ALARM
+12V:        +4.80 V  (min = +14.04 V, max = +15.38 V)   ALARM
-12V:        -1.83 V  (min =  +2.52 V, max =  +5.81 V)   ALARM
-5V:         -4.04 V  (min =  +5.00 V, max =  -4.85 V)   ALARM
V5SB:        +5.48 V  (min =  +1.26 V, max =  +2.77 V)   ALARM
VBat:        +3.26 V  (min =  +2.99 V, max =  +0.61 V)   ALARM
fan1:          0 RPM  (min = 168750 RPM, div = 2)  ALARM
fan2:          0 RPM  (min = 2667 RPM, div = 2)  ALARM
fan3:          0 RPM  (min = 4245 RPM, div = 2)  ALARM
temp1: +28.0°C (high = -65.0°C, hyst = -79.0°C) ALARM sensor = thermistor
temp2:       +32.0°C  (high = +80.0°C, hyst = +75.0°C)  sensor = thermistor
temp3:       -48.0°C  (high = +80.0°C, hyst = +75.0°C)  sensor = thermistor
cpu0_vid:   +1.500 V
beep_enable:enabled

I didn't even know there was an ISA adapter in the machine, but the values all look wacky.

Here is the output of hddtemp

hddtemp --unit=F SATA:/dev/sda SATA:/dev/sdb SATA:/dev/sdc
/dev/sda: Maxtor 6Y160M0: 77°F
/dev/sdb: WDC WD2500KS-00MJB0: 96°F
/dev/sdc: ST3750330AS: 80°F

This is becoming a science experiment because we are going to purchase a replacement for this machine, but I am trying to keep it up until the new machine becomes available, and maybe this exercise in futility may help someone else searching the list.

Thanks for the help,
Pete


[Date Prev][Date Next]   [Thread Prev][Thread Next]   [Thread Index] [Date Index] [Author Index]