Sun Fire V20z with FC2t2 x86-64
Brent J. Nordquist
b-nordquist at bethel.edu
Tue Apr 13 12:52:13 UTC 2004
I was able to successfully install FC2t2 x86-64 from CD-ROM (SELinux
permissive) onto the Sun Fire V20z (dual Opteron 244, 2GB memory, LSI1030
Ultra320 to one 36GB SCSI drive).
The only hitch was network; the Fire V20z has dual Broadcom BCM5703, and
the system hangs at "Bringing up interface eth0:" during (SMP) boot. In
single-user I can "modprobe tg3" and "service network start" and all is
well; lspci and dmesg appear below.
Disabling kudzu and booting UP kernel, and then adding acpi=off, didn't
help. Anything else I can/should try?
=== lspci -v ===
00:06.0 PCI bridge: Advanced Micro Devices [AMD] AMD-8111 PCI (rev 07) (prog-if 00 [Normal decode])
Flags: bus master, 66Mhz, medium devsel, latency 123
Bus: primary=00, secondary=01, subordinate=01, sec-latency=68
Memory behind bridge: fd100000-fe7fffff
Capabilities: [c0] #08 [0086]
Capabilities: [f0] #08 [8000]
00:07.0 ISA bridge: Advanced Micro Devices [AMD] AMD-8111 LPC (rev 05)
Subsystem: Advanced Micro Devices [AMD] AMD-8111 LPC
Flags: bus master, 66Mhz, medium devsel, latency 0
00:07.1 IDE interface: Advanced Micro Devices [AMD] AMD-8111 IDE (rev 03) (prog-if 8a [Master SecP PriP])
Subsystem: Newisys, Inc.: Unknown device 0010
Flags: bus master, medium devsel, latency 64
I/O ports at 1000 [size=16]
00:07.3 Bridge: Advanced Micro Devices [AMD] AMD-8111 ACPI (rev 05)
Subsystem: Newisys, Inc.: Unknown device 0010
Flags: medium devsel
00:0a.0 PCI bridge: Advanced Micro Devices [AMD] AMD-8131 PCI-X Bridge (rev 12) (prog-if 00 [Normal decode])
Flags: bus master, 66Mhz, medium devsel, latency 64
Bus: primary=00, secondary=02, subordinate=02, sec-latency=64
I/O behind bridge: 00002000-00002fff
Memory behind bridge: fe800000-fe8fffff
Expansion ROM at 00002000 [disabled] [size=4K]
Capabilities: [a0] PCI-X bridge device.
Capabilities: [b8] #08 [8000]
Capabilities: [c0] #08 [004a]
00:0a.1 PIC: Advanced Micro Devices [AMD] AMD-8131 PCI-X APIC (rev 01) (prog-if 10 [IO-APIC])
Subsystem: Newisys, Inc.: Unknown device 0010
Flags: bus master, medium devsel, latency 0
Memory at fd000000 (64-bit, non-prefetchable)
00:0b.0 PCI bridge: Advanced Micro Devices [AMD] AMD-8131 PCI-X Bridge (rev 12) (prog-if 00 [Normal decode])
Flags: bus master, 66Mhz, medium devsel, latency 64
Bus: primary=00, secondary=03, subordinate=03, sec-latency=64
Capabilities: [a0] PCI-X bridge device.
Capabilities: [b8] #08 [8000]
00:0b.1 PIC: Advanced Micro Devices [AMD] AMD-8131 PCI-X APIC (rev 01) (prog-if 10 [IO-APIC])
Subsystem: Newisys, Inc.: Unknown device 0010
Flags: bus master, medium devsel, latency 0
Memory at fd001000 (64-bit, non-prefetchable)
00:18.0 Host bridge: Advanced Micro Devices [AMD] K8 NorthBridge
Flags: fast devsel
Capabilities: [80] #08 [2101]
Capabilities: [a0] #08 [2101]
Capabilities: [c0] #08 [2101]
00:18.1 Host bridge: Advanced Micro Devices [AMD] K8 NorthBridge
Flags: fast devsel
00:18.2 Host bridge: Advanced Micro Devices [AMD] K8 NorthBridge
Flags: fast devsel
00:18.3 Host bridge: Advanced Micro Devices [AMD] K8 NorthBridge
Flags: fast devsel
00:19.0 Host bridge: Advanced Micro Devices [AMD] K8 NorthBridge
Flags: fast devsel
Capabilities: [80] #08 [2101]
Capabilities: [a0] #08 [2101]
Capabilities: [c0] #08 [2101]
00:19.1 Host bridge: Advanced Micro Devices [AMD] K8 NorthBridge
Flags: fast devsel
00:19.2 Host bridge: Advanced Micro Devices [AMD] K8 NorthBridge
Flags: fast devsel
00:19.3 Host bridge: Advanced Micro Devices [AMD] K8 NorthBridge
Flags: fast devsel
01:00.0 USB Controller: Advanced Micro Devices [AMD] AMD-8111 USB (rev 0b) (prog-if 10 [OHCI])
Subsystem: Newisys, Inc.: Unknown device 0010
Flags: bus master, medium devsel, latency 64, IRQ 19
Memory at fd120000 (32-bit, non-prefetchable)
01:00.1 USB Controller: Advanced Micro Devices [AMD] AMD-8111 USB (rev 0b) (prog-if 10 [OHCI])
Subsystem: Newisys, Inc.: Unknown device 0010
Flags: bus master, medium devsel, latency 64, IRQ 19
Memory at fd121000 (32-bit, non-prefetchable)
01:05.0 VGA compatible controller: Trident Microsystems Blade 3D PCI/AGP (rev 3a) (prog-if 00 [VGA])
Subsystem: Newisys, Inc.: Unknown device 0010
Flags: bus master, 66Mhz, medium devsel, latency 64, IRQ 16
Memory at fe000000 (32-bit, non-prefetchable)
Memory at fd100000 (32-bit, non-prefetchable) [size=128K]
Memory at fd800000 (32-bit, non-prefetchable) [size=8M]
Capabilities: [80] AGP version 1.0
Capabilities: [90] Power Management version 1
02:02.0 Ethernet controller: Broadcom Corporation NetXtreme BCM5703 Gigabit Ethernet (rev 02)
Subsystem: Newisys, Inc.: Unknown device 0010
Flags: bus master, 66Mhz, medium devsel, latency 64, IRQ 25
Memory at fe800000 (64-bit, non-prefetchable)
Capabilities: [40] PCI-X non-bridge device.
Capabilities: [48] Power Management version 2
Capabilities: [50] Vital Product Data
Capabilities: [58] Message Signalled Interrupts: 64bit+ Queue=0/3 Enable-
02:03.0 Ethernet controller: Broadcom Corporation NetXtreme BCM5703 Gigabit Ethernet (rev 02)
Subsystem: Newisys, Inc.: Unknown device 0010
Flags: bus master, 66Mhz, medium devsel, latency 64, IRQ 26
Memory at fe810000 (64-bit, non-prefetchable)
Capabilities: [40] PCI-X non-bridge device.
Capabilities: [48] Power Management version 2
Capabilities: [50] Vital Product Data
Capabilities: [58] Message Signalled Interrupts: 64bit+ Queue=0/3 Enable-
02:04.0 SCSI storage controller: LSI Logic / Symbios Logic 53c1030 PCI-X Fusion-MPT Dual Ultra320 SCSI (rev 07)
Subsystem: Newisys, Inc.: Unknown device 0010
Flags: bus master, 66Mhz, medium devsel, latency 72, IRQ 27
I/O ports at 2000
Memory at fe830000 (64-bit, non-prefetchable) [size=64K]
Memory at fe820000 (64-bit, non-prefetchable) [size=64K]
Capabilities: [50] Power Management version 2
Capabilities: [58] Message Signalled Interrupts: 64bit+ Queue=0/0 Enable-
Capabilities: [68] PCI-X non-bridge device.
=== dmesg ===
UN V20z 0x06040000 SUN 0x00000001) @ 0x000000007ff72e72
ACPI: MADT (v001 PTLTD APIC 0x06040000 LTP 0x00000000) @ 0x000000007ff72f3a
ACPI: SPCR (v001 PTLTD $UCRTBL$ 0x06040000 PTL 0x00000001) @ 0x000000007ff72fb0
ACPI: DSDT (v001 SUN V20z 0x06040000 MSFT 0x0100000e) @ 0x0000000000000000
ACPI: Local APIC address 0x00000000fee00000
ACPI: LAPIC (acpi_id[0x00] lapic_id[0x00] enabled)
Processor #0 15:5 APIC version 16
ACPI: LAPIC (acpi_id[0x01] lapic_id[0x01] enabled)
Processor #1 15:5 APIC version 16
ACPI: LAPIC_NMI (acpi_id[0x00] high edge lint[0x1])
ACPI: LAPIC_NMI (acpi_id[0x01] high edge lint[0x1])
ACPI: IOAPIC (id[0x02] address[0xfec00000] global_irq_base[0x0])
IOAPIC[0]: Assigned apic_id 2
IOAPIC[0]: apic_id 2, version 17, address 0xfec00000, IRQ 0-23
ACPI: IOAPIC (id[0x03] address[0xfd000000] global_irq_base[0x18])
IOAPIC[1]: Assigned apic_id 3
IOAPIC[1]: apic_id 3, version 17, address 0xfd000000, IRQ 24-27
ACPI: IOAPIC (id[0x04] address[0xfd001000] global_irq_base[0x1c])
IOAPIC[2]: Assigned apic_id 4
IOAPIC[2]: apic_id 4, version 17, address 0xfd001000, IRQ 28-31
ACPI: INT_SRC_OVR (bus 0 bus_irq 0 global_irq 2 high edge)
Using ACPI (MADT) for SMP configuration information
Checking aperture...
CPU 0: aperture @ 0 size 32 MB
No AGP bridge found
Built 2 zonelists
Kernel command line: ro root=LABEL=/ single console=tty0
Initializing CPU#0
PID hash table entries: 16 (order 4: 256 bytes)
time.c: Using 1.193182 MHz PIT timer.
time.c: Detected 1792.015 MHz processor.
Console: colour VGA+ 80x25
Memory: 2049540k/2096576k available (1922k kernel code, 0k reserved, 1224k data, 180k init)
Calibrating delay loop... 3522.56 BogoMIPS
Security Scaffold v1.0.0 initialized
SELinux: Initializing.
SELinux: Starting in permissive mode
There is already a security framework initialized, register_security failed.
Failure registering capabilities with the kernel
selinux_register_security: Registering secondary module capability
Capability LSM initialized
Dentry cache hash table entries: 16384 (order: 5, 131072 bytes)
Inode-cache hash table entries: 16384 (order: 5, 131072 bytes)
Mount-cache hash table entries: 256 (order: 0, 4096 bytes)
checking if image is initramfs...it isn't (no cpio magic); looks like an initrd
CPU: L1 I Cache: 64K (64 bytes/line), D cache 64K (64 bytes/line)
CPU: L2 Cache: 1024K (64 bytes/line)
POSIX conformance testing by UNIFIX
Using local APIC NMI watchdog using perfctr0
CPU: L1 I Cache: 64K (64 bytes/line), D cache 64K (64 bytes/line)
CPU: L2 Cache: 1024K (64 bytes/line)
CPU0: AMD Opteron(tm) Processor 244 stepping 08
per-CPU timeslice cutoff: 1024.00 usecs.
task migration cache decay timeout: 2 msecs.
Booting processor 1/1 rip 6000 rsp 1003ff0df58
Initializing CPU#1
Calibrating delay loop... 3579.90 BogoMIPS
CPU: L1 I Cache: 64K (64 bytes/line), D cache 64K (64 bytes/line)
CPU: L2 Cache: 1024K (64 bytes/line)
AMD Opteron(tm) Processor 244 stepping 08
Total of 2 processors activated (7102.46 BogoMIPS).
ENABLING IO-APIC IRQs
init IO_APIC IRQs
IO-APIC (apicid-pin) 2-0, 2-16, 2-17, 2-18, 2-19, 2-20, 2-21, 2-22, 2-23, 3-0, 3-1, 3-2, 3-3, 4-0, 4-1, 4-2, 4-3 not connected.
..TIMER: vector=0x31 pin1=2 pin2=-1
Using local APIC timer interrupts.
Detected 12.444 MHz APIC timer.
checking TSC synchronization across 2 CPUs: passed.
time.c: Using PIT/TSC based timekeeping.
Brought up 2 CPUs
NET: Registered protocol family 16
PCI: Using configuration type 1
mtrr: v2.0 (20020519)
ACPI: Subsystem revision 20040220
ACPI: Interpreter enabled
ACPI: Using IOAPIC for interrupt routing
ACPI: PCI Root Bridge [PCI0] (00:00)
PCI: Probing PCI hardware (bus 00)
ACPI: PCI Interrupt Link [LNKA] (IRQs 3 5 *10 11)
ACPI: PCI Interrupt Link [LNKB] (IRQs 3 *5 10 11)
ACPI: PCI Interrupt Link [LNKC] (IRQs *3 5 10 11)
ACPI: PCI Interrupt Link [LNKD] (IRQs 3 5 10 *11)
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.THOR._PRT]
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.Z000._PRT]
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.Z002._PRT]
IOAPIC[0]: Set PCI routing entry (2-16 -> 0xa9 -> IRQ 16 Mode:1 Active:1)
00:01:00[A] -> 2-16 -> IRQ 16
IOAPIC[0]: Set PCI routing entry (2-17 -> 0xb1 -> IRQ 17 Mode:1 Active:1)
00:01:00[B] -> 2-17 -> IRQ 17
IOAPIC[0]: Set PCI routing entry (2-18 -> 0xb9 -> IRQ 18 Mode:1 Active:1)
00:01:00[C] -> 2-18 -> IRQ 18
IOAPIC[0]: Set PCI routing entry (2-19 -> 0xc1 -> IRQ 19 Mode:1 Active:1)
00:01:00[D] -> 2-19 -> IRQ 19
IOAPIC[1]: Set PCI routing entry (3-1 -> 0xc9 -> IRQ 25 Mode:1 Active:1)
00:02:02[A] -> 3-1 -> IRQ 25
IOAPIC[1]: Set PCI routing entry (3-2 -> 0xd1 -> IRQ 26 Mode:1 Active:1)
00:02:03[A] -> 3-2 -> IRQ 26
IOAPIC[1]: Set PCI routing entry (3-3 -> 0xd9 -> IRQ 27 Mode:1 Active:1)
00:02:04[A] -> 3-3 -> IRQ 27
IOAPIC[1]: Set PCI routing entry (3-0 -> 0xe1 -> IRQ 24 Mode:1 Active:1)
00:02:05[A] -> 3-0 -> IRQ 24
IOAPIC[2]: Set PCI routing entry (4-0 -> 0xe9 -> IRQ 28 Mode:1 Active:1)
00:03:01[A] -> 4-0 -> IRQ 28
IOAPIC[2]: Set PCI routing entry (4-1 -> 0x32 -> IRQ 29 Mode:1 Active:1)
00:03:01[B] -> 4-1 -> IRQ 29
IOAPIC[2]: Set PCI routing entry (4-2 -> 0x3a -> IRQ 30 Mode:1 Active:1)
00:03:01[C] -> 4-2 -> IRQ 30
IOAPIC[2]: Set PCI routing entry (4-3 -> 0x42 -> IRQ 31 Mode:1 Active:1)
00:03:01[D] -> 4-3 -> IRQ 31
number of MP IRQ sources: 15.
number of IO-APIC #2 registers: 24.
number of IO-APIC #3 registers: 4.
number of IO-APIC #4 registers: 4.
testing the IO APIC.......................
IO APIC #2......
.... register #00: 02000000
....... : physical APIC id: 02
.... register #01: 00170011
....... : max redirection entries: 0017
....... : PRQ implemented: 0
....... : IO APIC version: 0011
.... register #02: 02000000
....... : arbitration: 02
.... IRQ redirection table:
NR Log Phy Mask Trig IRR Pol Stat Dest Deli Vect:
00 000 00 1 0 0 0 0 0 0 00
01 001 01 0 0 0 0 0 1 1 39
02 001 01 0 0 0 0 0 1 1 31
03 001 01 0 0 0 0 0 1 1 41
04 001 01 0 0 0 0 0 1 1 49
05 001 01 0 0 0 0 0 1 1 51
06 001 01 0 0 0 0 0 1 1 59
07 001 01 0 0 0 0 0 1 1 61
08 001 01 0 0 0 0 0 1 1 69
09 001 01 0 0 0 0 0 1 1 71
0a 001 01 0 0 0 0 0 1 1 79
0b 001 01 0 0 0 0 0 1 1 81
0c 001 01 0 0 0 0 0 1 1 89
0d 001 01 0 0 0 0 0 1 1 91
0e 001 01 0 0 0 0 0 1 1 99
0f 001 01 0 0 0 0 0 1 1 A1
10 001 01 1 1 0 1 0 1 1 A9
11 001 01 1 1 0 1 0 1 1 B1
12 001 01 1 1 0 1 0 1 1 B9
13 001 01 1 1 0 1 0 1 1 C1
14 000 00 1 0 0 0 0 0 0 00
15 000 00 1 0 0 0 0 0 0 00
16 000 00 1 0 0 0 0 0 0 00
17 000 00 1 0 0 0 0 0 0 00
IO APIC #3......
.... register #00: 03000000
....... : physical APIC id: 03
.... register #01: 00030011
....... : max redirection entries: 0003
....... : PRQ implemented: 0
....... : IO APIC version: 0011
.... register #02: 00000000
....... : arbitration: 00
.... IRQ redirection table:
NR Log Phy Mask Trig IRR Pol Stat Dest Deli Vect:
00 001 01 1 1 0 1 0 1 1 E1
01 001 01 1 1 0 1 0 1 1 C9
02 001 01 1 1 0 1 0 1 1 D1
03 001 01 1 1 0 1 0 1 1 D9
IO APIC #4......
.... register #00: 04000000
....... : physical APIC id: 04
.... register #01: 00030011
....... : max redirection entries: 0003
....... : PRQ implemented: 0
....... : IO APIC version: 0011
.... register #02: 00000000
....... : arbitration: 00
.... IRQ redirection table:
NR Log Phy Mask Trig IRR Pol Stat Dest Deli Vect:
00 001 01 1 1 0 1 0 1 1 E9
01 001 01 1 1 0 1 0 1 1 32
02 001 01 1 1 0 1 0 1 1 3A
03 001 01 1 1 0 1 0 1 1 42
IRQ to pin mappings:
IRQ0 -> 0:2
IRQ1 -> 0:1
IRQ3 -> 0:3
IRQ4 -> 0:4
IRQ5 -> 0:5
IRQ6 -> 0:6
IRQ7 -> 0:7
IRQ8 -> 0:8
IRQ9 -> 0:9
IRQ10 -> 0:10
IRQ11 -> 0:11
IRQ12 -> 0:12
IRQ13 -> 0:13
IRQ14 -> 0:14
IRQ15 -> 0:15
IRQ16 -> 0:16
IRQ17 -> 0:17
IRQ18 -> 0:18
IRQ19 -> 0:19
IRQ24 -> 1:0
IRQ25 -> 1:1
IRQ26 -> 1:2
IRQ27 -> 1:3
IRQ28 -> 2:0
IRQ29 -> 2:1
IRQ30 -> 2:2
IRQ31 -> 2:3
.................................... done.
PCI: Using ACPI for IRQ routing
PCI: if you experience problems, try using option 'pci=noacpi' or even 'acpi=off'
PCI-DMA: Disabling IOMMU.
Total HugeTLB memory allocated, 0
IA32 emulation $Id: sys_ia32.c,v 1.32 2002/03/24 13:02:28 ak Exp $
audit: initializing netlink socket (disabled)
audit(1081840680.372:0): initialized
VFS: Disk quotas dquot_6.5.1
SELinux: Registering netfilter hooks
Initializing Cryptographic API
pci_hotplug: PCI Hot Plug PCI Core version: 0.5
ACPI: Processor [CPU0] (supports C1)
ACPI: Processor [CPU1] (supports C1)
Real Time Clock Driver v1.12
Linux agpgart interface v0.100 (c) Dave Jones
Serial: 8250/16550 driver $Revision: 1.90 $ 8 ports, IRQ sharing enabled
ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A
RAMDISK driver initialized: 16 RAM disks of 8192K size 1024 blocksize
divert: not allocating divert_blk for non-ethernet device lo
Uniform Multi-Platform E-IDE driver Revision: 7.00alpha2
ide: Assuming 33MHz system bus speed for PIO modes; override with idebus=xx
AMD8111: IDE controller at PCI slot 0000:00:07.1
AMD8111: chipset revision 3
AMD8111: not 100% native mode: will probe irqs later
AMD8111: 0000:00:07.1 (rev 03) UDMA133 controller
ide0: BM-DMA at 0x1000-0x1007, BIOS settings: hda:pio, hdb:pio
ide1: BM-DMA at 0x1008-0x100f, BIOS settings: hdc:DMA, hdd:pio
hdc: CD-224E, ATAPI CD/DVD-ROM drive
Using anticipatory io scheduler
ide1 at 0x170-0x177,0x376 on irq 15
ide-floppy driver 0.99.newide
mice: PS/2 mouse device common for all mice
serio: i8042 AUX port at 0x60,0x64 irq 12
serio: i8042 KBD port at 0x60,0x64 irq 1
input: AT Translated Set 2 keyboard on isa0060/serio0
md: md driver 0.90.0 MAX_MD_DEVS=256, MD_SB_DISKS=27
NET: Registered protocol family 2
IP: routing cache hash table of 8192 buckets, 128Kbytes
TCP: Hash tables configured (established 262144 bind 65536)
Initializing IPsec netlink socket
NET: Registered protocol family 1
NET: Registered protocol family 17
ACPI: (supports S0 S1 S5)
md: Autodetecting RAID arrays.
md: autorun ...
md: ... autorun DONE.
RAMDISK: Compressed image found at block 0
VFS: Mounted root (ext2 filesystem).
SCSI subsystem initialized
Fusion MPT base driver 3.00.03
Copyright (c) 1999-2003 LSI Logic Corporation
mptbase: Initiating ioc0 bringup
ioc0: 53C1030: Capabilities={Initiator}
Fusion MPT SCSI Host driver 3.00.03
scsi0 : ioc0: LSI53C1030, FwRev=01030a00h, Ports=1, MaxQ=222, IRQ=27
Vendor: SEAGATE Model: ST336607LC Rev: 0007
Type: Direct-Access ANSI SCSI revision: 03
SCSI device sda: 71687372 512-byte hdwr sectors (36704 MB)
SCSI device sda: drive cache: write back
sda: sda1 sda2 sda3 sda4 < sda5 sda6 >
Attached scsi disk sda at scsi0, channel 0, id 0, lun 0
EXT3-fs: INFO: recovery required on readonly filesystem.
EXT3-fs: write access will be enabled during recovery.
kjournald starting. Commit interval 5 seconds
EXT3-fs: recovery complete.
EXT3-fs: mounted filesystem with ordered data mode.
Freeing unused kernel memory: 180k freed
security: 3 users, 5 roles, 1166 types
security: 30 classes, 261889 rules
SELinux: Completing initialization.
SELinux: Setting up existing superblocks.
SELinux: initialized (dev , type selinuxfs), uses genfs_contexts
SELinux: initialized (dev sda1, type ext3), uses xattr
SELinux: initialized (dev ram0, type ext2), uses xattr
SELinux: initialized (dev , type hugetlbfs), not configured for labeling
SELinux: initialized (dev , type devpts), uses transition SIDs
SELinux: initialized (dev , type eventpollfs), uses genfs_contexts
SELinux: initialized (dev , type pipefs), uses task SIDs
SELinux: initialized (dev , type tmpfs), uses transition SIDs
SELinux: initialized (dev , type futexfs), uses genfs_contexts
SELinux: initialized (dev , type sockfs), uses task SIDs
SELinux: initialized (dev , type proc), uses genfs_contexts
SELinux: initialized (dev , type bdev), uses genfs_contexts
SELinux: initialized (dev , type rootfs), uses genfs_contexts
SELinux: initialized (dev , type sysfs), uses genfs_contexts
audit(1081840690.766:0): avc: denied { search } for pid=55 exe=/bin/dmesg name=usr dev=sda1 ino=58497 scontext=system_u:system_r:dmesg_t tcontext=system_u:object_r:file_t tclass=dir
audit(1081840690.822:0): avc: denied { search } for pid=64 exe=/sbin/hwclock name=usr dev=sda1 ino=58497 scontext=system_u:system_r:hwclock_t tcontext=system_u:object_r:file_t tclass=dir
audit(1081840692.114:0): avc: denied { search } for pid=76 exe=/bin/hostname name=usr dev=sda1 ino=58497 scontext=system_u:system_r:hostname_t tcontext=system_u:object_r:file_t tclass=dir
ACPI: Power Button (FF) [PWRF]
ACPI: Sleep Button (FF) [SLPF]
drivers/usb/core/usb.c: registered new driver usbfs
drivers/usb/core/usb.c: registered new driver hub
ohci_hcd: 2004 Feb 02 USB 1.1 'Open' Host Controller (OHCI) Driver (PCI)
ohci_hcd: block sizes: ed 80 td 96
ohci_hcd 0000:01:00.0: OHCI Host Controller
ohci_hcd 0000:01:00.0: irq 19, pci mem ffffff0000019000
SELinux: initialized (dev , type usbdevfs), uses genfs_contexts
SELinux: initialized (dev , type usbfs), uses genfs_contexts
ohci_hcd 0000:01:00.0: new USB bus registered, assigned bus number 1
hub 1-0:1.0: USB hub found
hub 1-0:1.0: 3 ports detected
ohci_hcd 0000:01:00.1: OHCI Host Controller
ohci_hcd 0000:01:00.1: irq 19, pci mem ffffff000001b000
ohci_hcd 0000:01:00.1: new USB bus registered, assigned bus number 2
hub 2-0:1.0: USB hub found
hub 2-0:1.0: 3 ports detected
EXT3 FS on sda1, internal journal
Adding 2096440k swap on /dev/sda5. Priority:-1 extents:1
SELinux: initialized (dev , type tmpfs), uses transition SIDs
kjournald starting. Commit interval 5 seconds
EXT3 FS on sda6, internal journal
EXT3-fs: mounted filesystem with ordered data mode.
SELinux: initialized (dev sda6, type ext3), uses xattr
kjournald starting. Commit interval 5 seconds
EXT3 FS on sda2, internal journal
EXT3-fs: mounted filesystem with ordered data mode.
SELinux: initialized (dev sda2, type ext3), uses xattr
kjournald starting. Commit interval 5 seconds
EXT3 FS on sda3, internal journal
EXT3-fs: mounted filesystem with ordered data mode.
SELinux: initialized (dev sda3, type ext3), uses xattr
tg3.c:v2.9 (March 8, 2004)
divert: allocating divert_blk for eth0
eth0: Tigon3 [partno(BCM95703A30) rev 1002 PHY(5703)] (PCIX:100MHz:64-bit) 10/100/1000BaseT Ethernet 00:09:3d:00:09:1f
divert: allocating divert_blk for eth1
eth1: Tigon3 [partno(BCM95703A30) rev 1002 PHY(5703)] (PCIX:100MHz:64-bit) 10/100/1000BaseT Ethernet 00:09:3d:00:09:1f
ip_tables: (C) 2000-2002 Netfilter core team
ip_tables: (C) 2000-2002 Netfilter core team
tg3: eth0: Link is up at 100 Mbps, full duplex.
tg3: eth0: Flow control is on for TX and on for RX.
ip_tables: (C) 2000-2002 Netfilter core team
--
Brent J. Nordquist <b-nordquist at bethel.edu> N0BJN
Other contact information: http://kepler.acns.bethel.edu/~bjn/contact.html
More information about the fedora-test-list
mailing list