[Date Prev][Date Next]   [Thread Prev][Thread Next]   [Thread Index] [Date Index] [Author Index]

sbp2 firewire failure on kernels 2.6.1-1.61, 2.6.2-1.81



I get the following errors when I turn on my external hard drive
enclosure:
------------------------------------------------------------------
ieee1394: got invalid ack 11 from node 65472 (tcode 4)
ieee1394: got invalid ack 11 from node 65472 (tcode 4)
ieee1394: got invalid ack 11 from node 65472 (tcode 4)
ieee1394: ConfigROM quadlet transaction error for node 0-00:1023
ieee1394: Node changed: 0-00:1023 -> 0-01:1023
------------------------------------------------------------------
sbp2 does *not* get loaded automatically.

If I unload ohci1394 and reload it, I get:
------------------------------------------------------------------
ieee1394: ConfigROM quadlet transaction error for node 0-00:1023
ohci1394: $Rev: 1097 $ Ben Collins <bcollins debian org>
ohci1394: fw-host0: OHCI-1394 1.0 (PCI): IRQ=[9] 
MMIO=[d0202000-d02027ff]  Max Packet=[2048]
ieee1394: Node added: ID:BUS[0-00:1023]  GUID[005077350710020e]
ieee1394: Host added: ID:BUS[0-01:1023]  GUID[08004603015ea68f]
ieee1394: unsolicited response packet received - no tlabel match
sbp2: $Rev: 1096 $ Ben Collins <bcollins debian org>
ieee1394: sbp2: Driver forced to serialize I/O (serialize_io = 1)
scsi1 : SCSI emulation for IEEE-1394 SBP-2 Devices
ieee1394: sbp2: sbp2_firmware_revision = 100102
-------------------------------------------------------------------
Still no drive detected, until I attempt to mount a partition:

ieee1394: sbp2: Logged into SBP-2 device
ieee1394: sbp2: Node 0-00:1023: Max speed [S400] - Max payload [2048]
  Vendor: ST312002  Model: 2A                Rev:
  Type:   Direct-Access                      ANSI SCSI revision: 06
SCSI device sdb: 234467403 512-byte hdwr sectors (120047 MB)
sdb: asking for cache data failed
sdb: assuming drive cache: write through
 sdb:<3>ieee1394: sbp2: aborting sbp2 command
Read (10) 00 0d f9 b0 48 00 00 03 00
ieee1394: sbp2: aborting sbp2 command
Test Unit Ready 00 00 00 00 00
ieee1394: sbp2: reset requested
ieee1394: sbp2: Generating sbp2 fetch agent reset
ieee1394: sbp2: aborting sbp2 command
Test Unit Ready 00 00 00 00 00
ieee1394: sbp2: reset requested
ieee1394: sbp2: Generating sbp2 fetch agent reset
eth1: New link status: Disconnected (0002)
eth1: New link status: Connected (0001)
ieee1394: sbp2: aborting sbp2 command
Test Unit Ready 00 00 00 00 00
ieee1394: sbp2: reset requested
ieee1394: sbp2: Generating sbp2 fetch agent reset

What is the status of firewire support on FC2-devel? It is quite worrying
it seems to be retrogressing ever since 2.4.21 was released (first
requiring rescan-scsi-bus.sh, and now this). Is there any possibility of
shipping a 2.4 kernel in addition to 2.6 for FC2 final?

Hardware's Sony Vaio Z1MP, Centrino (Pentium-M 1.3GHz) with a USB memory
stick interface.

Relevant lsmod lines:
sbp2                   27656  0
ohci1394               41860  0
sd_mod                 16928  0
usb_storage            65984  0
scsi_mod              124600  4 sbp2,sg,sd_mod,usb_storage

Has anyone run into a similar problem? Bugzilla has nothing to say on
that - I'll probably file a report tomorrow.

Thanks,

- Michel

-- 
http://www.fastmail.fm - I mean, what is it about a decent email service?




[Date Prev][Date Next]   [Thread Prev][Thread Next]   [Thread Index] [Date Index] [Author Index]