Problems with Xen (kernel-xen0-2.6.11-1.1226_FC4) and Intel Corporation 82562ET/EZ/GT/GZ Ethernet

Keith Sharp kms at passback.co.uk
Wed Apr 6 17:28:18 UTC 2005


Hello,

I have been trying to get Xen working with the most recent kernel builds
from Rawhide.  When I boot using Xen and kernel-xen0 the network fails
and I get tracebacks on the console.

Booting starts as expected but starting eth0 seems to take a little
longer than normal.  The problems begin when NTP is started, booting
pauses here for quite a few seconds and then a traceback appears.
Booting eventually continues with these pauses and tracebacks.  When the
system is finally up I can login is root and the network appears to be
up (according to ifconfig) but I cannot ping any other local devices and
the RX and TX values for eth0 remain at zero.

Attached is a console log from booting - the interesting stuff is
towards the end, the output of lspci, and my grub.conf

I am running FC4T1 with kernel and xen updated from Rawhide:

kernel-xen0-2.6.11-1.1226_FC4
kernel-smp-2.6.11-1.1226_FC4
kernel-2.6.11-1.1226_FC4
kernel-xenU-2.6.11-1.1226_FC4

The Ethernet port works fine under the standard SMP kernel.

Is anyone else seeing this?

Keith.
-------------- next part --------------
00:00.0 Host bridge: Intel Corporation 915G/P/GV Processor to I/O Controller (rev 04)
00:01.0 PCI bridge: Intel Corporation 915G/P/GV PCI Express Root Port (rev 04)
00:1c.0 PCI bridge: Intel Corporation 82801FB/FBM/FR/FW/FRW (ICH6 Family) PCI Express Port 1 (rev 03)
00:1d.0 USB Controller: Intel Corporation 82801FB/FBM/FR/FW/FRW (ICH6 Family) USB UHCI #1 (rev 03)
00:1d.1 USB Controller: Intel Corporation 82801FB/FBM/FR/FW/FRW (ICH6 Family) USB UHCI #2 (rev 03)
00:1d.2 USB Controller: Intel Corporation 82801FB/FBM/FR/FW/FRW (ICH6 Family) USB UHCI #3 (rev 03)
00:1d.3 USB Controller: Intel Corporation 82801FB/FBM/FR/FW/FRW (ICH6 Family) USB UHCI #4 (rev 03)
00:1d.7 USB Controller: Intel Corporation 82801FB/FBM/FR/FW/FRW (ICH6 Family) USB2 EHCI Controller (rev 03)
00:1e.0 PCI bridge: Intel Corporation 82801 PCI Bridge (rev d3)
00:1e.2 Multimedia audio controller: Intel Corporation 82801FB/FBM/FR/FW/FRW (ICH6 Family) AC'97 Audio Controller (rev 03)
00:1f.0 ISA bridge: Intel Corporation 82801FB/FR (ICH6/ICH6R) LPC Interface Bridge (rev 03)
00:1f.1 IDE interface: Intel Corporation 82801FB/FBM/FR/FW/FRW (ICH6 Family) IDE Controller (rev 03)
00:1f.2 IDE interface: Intel Corporation 82801FB/FW (ICH6/ICH6W) SATA Controller (rev 03)
00:1f.3 SMBus: Intel Corporation 82801FB/FBM/FR/FW/FRW (ICH6 Family) SMBus Controller (rev 03)
01:00.0 VGA compatible controller: ATI Technologies Inc RV370 5B60 [Radeon X300 (PCIE)]
01:00.1 Display controller: ATI Technologies Inc: Unknown device 5b70
03:01.0 Modem: Intel Corporation: Unknown device 1080 (rev 04)
03:08.0 Ethernet controller: Intel Corporation 82562ET/EZ/GT/GZ - PRO/100 VE (LOM) Ethernet Controller (rev 03)
-------------- next part --------------

 __  __            _____  ___         _                _
 \ \/ /___ _ __   |___ / / _ \     __| | _____   _____| |
  \  // _ \ '_ \    |_ \| | | |__ / _` |/ _ \ \ / / _ \ |
  /  \  __/ | | |  ___) | |_| |__| (_| |  __/\ V /  __/ |
 /_/\_\___|_| |_| |____(_)___/    \__,_|\___| \_/ \___|_|

 http://www.cl.cam.ac.uk/netos/xen
 University of Cambridge Computer Laboratory

 Xen version 3.0-devel (bhcompile at build.redhat.com) (gcc version 4.0.0 200503295 Latest ChangeSet: information unavailable

(XEN) Physical RAM map:
(XEN)  0000000000000000 - 00000000000a0000 (usable)
(XEN)  00000000000f0000 - 0000000000100000 (reserved)
(XEN)  0000000000100000 - 000000003fe88c00 (usable)
(XEN)  000000003fe88c00 - 000000003fe8ac00 (ACPI NVS)
(XEN)  000000003fe8ac00 - 000000003fe8cc00 (ACPI data)
(XEN)  000000003fe8cc00 - 0000000040000000 (reserved)
(XEN)  00000000e0000000 - 00000000f0000000 (reserved)
(XEN)  00000000fec00000 - 00000000fed00400 (reserved)
(XEN)  00000000fed20000 - 00000000feda0000 (reserved)
(XEN)  00000000fee00000 - 00000000fef00000 (reserved)
(XEN)  00000000ffb00000 - 0000000100000000 (reserved)
(XEN) System RAM: 1022MB (1046688kB)
(XEN) Xen heap: 10MB (10828kB)
(XEN) CPU0: Before vendor init, caps: bfebfbff 00000000 00000000, vendor = 0
(XEN) CPU#0: Physical ID: 0, Logical ID: 0
(XEN) CPU caps: bfebfbff 00000000 00000000 00000000
(XEN) found SMP MP-table at 000fe710
(XEN) ACPI: RSDP (v000 DELL                                      ) @ 0x000fec00
(XEN) ACPI: RSDT (v001 DELL    4700    0x00000007 ASL  0x00000061) @ 0x000fcc10
(XEN) ACPI: FADT (v001 DELL    4700    0x00000007 ASL  0x00000061) @ 0x000fcc50
(XEN) ACPI: SSDT (v001   DELL    st_ex 0x00001000 MSFT 0x0100000d) @ 0xfffc58e5
(XEN) ACPI: MADT (v001 DELL    4700    0x00000007 ASL  0x00000061) @ 0x000fccc4
(XEN) ACPI: BOOT (v001 DELL    4700    0x00000007 ASL  0x00000061) @ 0x000fcd36
(XEN) ACPI: ASF! (v016 DELL    4700    0x00000007 ASL  0x00000061) @ 0x000fcd5e
(XEN) ACPI: MCFG (v001 DELL    4700    0x00000007 ASL  0x00000061) @ 0x000fcdc5
(XEN) ACPI: HPET (v001 DELL    4700    0x00000007 ASL  0x00000061) @ 0x000fce03
(XEN) ACPI: DSDT (v001   DELL    dt_ex 0x00001000 MSFT 0x0100000d) @ 0x00000000
(XEN) ACPI: Local APIC address 0xfee00000
(XEN) ACPI: LAPIC (acpi_id[0x01] lapic_id[0x00] enabled)
(XEN) Processor #0 Unknown CPU [15:3] APIC version 20
(XEN) ACPI: LAPIC (acpi_id[0x02] lapic_id[0x01] enabled)
(XEN) Processor #1 Unknown CPU [15:3] APIC version 20
(XEN) ACPI: LAPIC (acpi_id[0x03] lapic_id[0x01] disabled)
(XEN) ACPI: LAPIC (acpi_id[0x04] lapic_id[0x07] disabled)
(XEN) ACPI: LAPIC_NMI (acpi_id[0xff] high level lint[0x1])
(XEN) Using ACPI for processor (LAPIC) configuration information
(XEN) Intel MultiProcessor Specification v1.4
(XEN)     Virtual Wire compatibility mode.
(XEN) OEM ID: DELL     Product ID: Dim 4700     APIC at: 0xFEE00000
(XEN) I/O APIC #8 Version 32 at 0xFEC00000.
(XEN) Enabling APIC mode: Flat. Using 1 I/O APICs
(XEN) Processors: 2
(XEN) Using scheduler: Borrowed Virtual Time (bvt)
(XEN) Initializing CPU#0
(XEN) Detected 2992.657 MHz processor.
(XEN) CPU0: Before vendor init, caps: bfebfbff 00000000 00000000, vendor = 0
(XEN) CPU#0: Physical ID: 0, Logical ID: 0
(XEN) CPU caps: bfebfbff 00000000 00000000 00000000
(XEN) CPU0 booted
(XEN) enabled ExtINT on CPU#0
(XEN) ESR value before enabling vector: 00000040
(XEN) ESR value after enabling vector: 00000000
(XEN) Booting processor 1/1 eip 90000
(XEN) Initializing CPU#1
(XEN) masked ExtINT on CPU#1
(XEN) ESR value before enabling vector: 00000000
(XEN) ESR value after enabling vector: 00000000
(XEN) CPU1: Before vendor init, caps: bfebfbff 00000000 00000000, vendor = 0
(XEN) CPU#1: Physical ID: 0, Logical ID: 1
(XEN) CPU caps: bfebfbff 00000000 00000000 00000000
(XEN) CPU1 has booted.
(XEN) Total of 2 processors activated.
(XEN) ENABLING IO-APIC IRQs
(XEN) Setting 8 in the phys_id_present_map
(XEN) ...changing IO-APIC physical APIC ID to 8 ... ok.
(XEN) init IO_APIC IRQs
(XEN) vector_irq[49] = 1
(XEN) vector_irq[51] = 3
(XEN) vector_irq[59] = 4
(XEN) vector_irq[61] = 5
(XEN) vector_irq[69] = 6
(XEN) vector_irq[71] = 7
(XEN) vector_irq[79] = 8
(XEN) vector_irq[81] = 9
(XEN) vector_irq[89] = 10
(XEN) vector_irq[91] = 11
(XEN) vector_irq[99] = 12
(XEN) vector_irq[a1] = 14
(XEN) vector_irq[a9] = 15
(XEN) vector_irq[b1] = 16
(XEN) vector_irq[b9] = 17
(XEN) vector_irq[c1] = 18
(XEN) vector_irq[c9] = 19
(XEN) vector_irq[d1] = 20
(XEN) vector_irq[d9] = 21
(XEN) vector_irq[e1] = 22
(XEN) vector_irq[e9] = 23
(XEN) ..TIMER: vector=0x41 pin1=2 pin2=0
(XEN) Using local APIC timer interrupts.
(XEN) Calibrating APIC timer for CPU0...
(XEN) ..... CPU speed is 2992.5999 MHz.
(XEN) ..... Bus speed is 199.5065 MHz.
(XEN) ..... bus_scale = 0x0000CC4F
(XEN) checking TSC synchronization across CPUs: passed.
(XEN) Time init:
(XEN) .... System Time: 20001255ns
(XEN) .... cpu_freq:    00000000:B2605588
(XEN) .... scale:       00000001:562BB70F
(XEN) .... Wall Clock:  1112802717s 200000us
(XEN) PCI: PCI BIOS revision 2.10 entry at 0xfb2cc, last bus=3
(XEN) PCI: Using configuration type 1
(XEN) PCI: Probing PCI hardware
(XEN) PCI: Probing PCI hardware (bus 00)
(XEN) PCI: Ignoring BAR0-3 of IDE controller 00:1f.1
(XEN) Transparent bridge - PCI device 8086:244e
(XEN) PCI: Using IRQ router PIIX/ICH [8086/2640] at 00:1f.0
(XEN) PCI->APIC IRQ transform: (B0,I29,P0) -> 21
(XEN) PCI->APIC IRQ transform: (B0,I29,P1) -> 22
(XEN) PCI->APIC IRQ transform: (B0,I29,P2) -> 18
(XEN) PCI->APIC IRQ transform: (B0,I29,P3) -> 23
(XEN) PCI->APIC IRQ transform: (B0,I29,P0) -> 21
(XEN) PCI->APIC IRQ transform: (B0,I30,P0) -> 23
(XEN) PCI->APIC IRQ transform: (B0,I31,P0) -> 16
(XEN) PCI->APIC IRQ transform: (B0,I31,P2) -> 20
(XEN) PCI->APIC IRQ transform: (B0,I31,P1) -> 17
(XEN) PCI->APIC IRQ transform: (B1,I0,P0) -> 16
(XEN) PCI->APIC IRQ transform: (B3,I1,P0) -> 17
(XEN) PCI: using PPB(B0,I30,P0) to get irq 23
(XEN) PCI->APIC IRQ transform: (B3,I8,P0) -> 23
(XEN) mtrr: v2.0 (20020519)
(XEN) *** LOADING DOMAIN 0 ***
(XEN) Xen-ELF header found: 'GUEST_OS=linux,GUEST_VER=2.6,XEN_VER=3.0,VIRT_BASE'(XEN) PHYSICAL MEMORY ARRANGEMENT:
(XEN)  Dom0 alloc.:   08000000->10000000
(XEN) VIRTUAL MEMORY ARRANGEMENT:
(XEN)  Loaded kernel: c0100000->c0478cfc
(XEN)  Init. ramdisk: c0479000->c078ea00
(XEN)  Phys-Mach map: c078f000->c07af000
(XEN)  Page tables:   c07af000->c07b3000
(XEN)  Start info:    c07b3000->c07b4000
(XEN)  Boot stack:    c07b4000->c07b5000
(XEN)  TOTAL:         c0000000->c0c00000
(XEN)  ENTRY ADDRESS: c0100000
(XEN) Initrd len 0x315a00, start at 0xc0479000
(XEN) Scrubbing Free RAM: ...........done.
(XEN) *** Serial input -> DOM0 (type 'CTRL-a' three times to switch input to Xe.Linux version 2.6.11-1.1226_FC4xen0 (bhcompile at decompose.build.redhat.com) (gcc5BIOS-provided physical RAM map:
 Xen: 0000000000000000 - 0000000008000000 (usable)
128MB LOWMEM available.
Using x86 segment limits to approximate NX protection
DMI 2.3 present.
IRQ lockup detection disabled
Allocating PCI resources starting at 08000000 (gap: 08000000:f8000000)
Built 1 zonelists
Kernel command line: ro root=/dev/volume_01/root console=ttyS0
Initializing CPU#0
PID hash table entries: 1024 (order: 10, 16384 bytes)
Xen reported: 2992.657 MHz processor.
Using tsc for high-res timesource
Console: colour VGA+ 80x25
Dentry cache hash table entries: 32768 (order: 5, 131072 bytes)
Inode-cache hash table entries: 16384 (order: 4, 65536 bytes)
Memory: 121600k/131072k available (2321k kernel code, 9388k reserved, 687k data)Checking if this processor honours the WP bit even in supervisor mode... Ok.
Security Framework v1.0.0 initialized
SELinux:  Initializing.
SELinux:  Starting in permissive mode
selinux_register_security:  Registering secondary module capability
Capability LSM initialized as secondary
Mount-cache hash table entries: 512
CPU: Trace cache: 12K uops, L1 D cache: 16K
CPU: L2 cache: 1024K
Enabling fast FPU save and restore... done.
Enabling unmasked SIMD FPU exception support... done.
Checking 'hlt' instruction... disabled
CPU0: Intel(R) Pentium(R) 4 CPU 3.00GHz stepping 04
per-CPU timeslice cutoff: 2925.83 usecs.
task migration cache decay timeout: 3 msecs.
Booting processor 1/1 eip c0100010
Initializing CPU#1
CPU: Trace cache: 12K uops, L1 D cache: 16K
CPU: L2 cache: 1024K
CPU1: Intel(R) Pentium(R) 4 CPU 3.00GHz stepping 04
Total of 2 processors activated (11953.76 BogoMIPS).
Brought up 2 CPUs
checking if image is initramfs... it is
Freeing initrd memory: 3158k freed
NET: Registered protocol family 16
PCI: Using configuration type Xen
Linux Plug and Play Support v0.97 (c) Adam Belay
xen_mem: Initialising balloon driver.
usbcore: registered new driver usbfs
usbcore: registered new driver hub
PCI: Probing PCI hardware
PCI: Probing PCI hardware (bus 00)
PCI: Ignoring BAR0-3 of IDE controller 0000:00:1f.1
PCI: Transparent bridge - 0000:00:1e.0
PCI: Probing PCI hardware (bus 01)
PCI: Probing PCI hardware (bus 03)
PCI: Probing PCI hardware
IA-32 Microcode Update Driver: v1.14-xen <tigran at veritas.com>
audit: initializing netlink socket (disabled)
audit(1112802721.290:0): initialized
Total HugeTLB memory allocated, 0
VFS: Disk quotas dquot_6.5.1
Dquot-cache hash table entries: 1024 (order 0, 4096 bytes)
SELinux:  Registering netfilter hooks
Initializing Cryptographic API
ksign: Installing public key data
Loading keyring
- Added public key 7A9F2968617F8655
- User ID: Red Hat, Inc. (Kernel Module GPG key)
(XEN) PCI: No IRQ known for interrupt pin A of device 00:01.0. Probably buggy M.Ti(XEN) mer ISR/1: Time went backwards: -79997000 4590000000 4000 4570000000PCI.
PCI: No IRQ known for interrupt pin A of device 0000:00:01.0.
pcie_portdrv_probe->Dev[2581:8086] has invalid IRQ. Check vendor BIOS
assign_interrupt_mode Found MSI capability
PCI: No IRQ known for interrupt pin A of device 0000:00:1c.0.
pcie_portdrv_probe->Dev[2660:8086] has invalid IRQ. Check vendor BIOS
assign_interrupt_mode Found MSI capability
isapnp: Scanning for PnP cards...
isapnp: No Plug & Play device found
Real Time Clock Driver v1.12
Linux agpgart interface v0.101 (c) Dave Jones
agpgart: Detected an Intel 915G Chipset.
agpgart: AGP aperture is 256M @ 0x0
[drm] Initialized drm 1.0.0 20040925
PNP: No PS/2 controller found. Probing ports directly.
serio: i8042 AUX port at 0x60,0x64 irq 12
serio: i8042 KBD port at 0x60,0x64 irq 1
io scheduler noop registered
io scheduler anticipatory registered
io scheduler deadline registered
io scheduler cfq registered
RAMDISK driver initialized: 16 RAM disks of 16384K size 1024 blocksize
Xen virtual console successfully installed as ttyS0
Event-channel device installed.
Initialising Xen netif backend
Uniform Multi-Platform E-IDE driver Revision: 7.00alpha2
ide: Assuming 33MHz system bus speed for PIO modes; override with idebus=xx
ICH6: IDE controller at PCI slot 0000:00:1f.1
PCI: Obtained IRQ 16 for device 0000:00:1f.1
ICH6: chipset revision 3
ICH6: not 100% native mode: will probe irqs later
    ide0: BM-DMA at 0xffa0-0xffa7, BIOS settings: hda:DMA, hdb:DMA
hda: GCR-8483B, ATAPI CD/DVD-ROM drive
hdb: _NEC DVD+RW ND-3100AD, ATAPI CD/DVD-ROM drive
ide0 at 0x1f0-0x1f7,0x3f6 on irq 14
hda: ATAPI 48X CD-ROM drive, 128kB Cache, UDMA(33)
Uniform CD-ROM driver Revision: 3.20
hdb: ATAPI 48X DVD-ROM CD-R/RW drive, 2048kB Cache, UDMA(33)
ide-floppy driver 0.99.newide
usbcore: registered new driver hiddev
usbcore: registered new driver usbhid
drivers/usb/input/hid-core.c: v2.01:USB HID core driver
mice: PS/2 mouse device common for all mice
md: md driver 0.90.1 MAX_MD_DEVS=256, MD_SB_DISKS=27
input: AT Translated Set 2 keyboard on isa0060/serio0
NET: Registered protocol family 2
IP: routing cache hash table of 512 buckets, 8Kbytes
TCP established hash table entries: 8192 (order: 5, 131072 bytes)
TCP bind hash table entries: 8192 (order: 4, 98304 bytes)
TCP: Hash tables configured (established 8192 bind 8192)
Initializing IPsec netlink socket
NET: Registered protocol family 1
NET: Registered protocol family 17
Freeing unused kernel memory: 196k freed
Red Hat nash version 4.2.1 starting
Mounted /proc filesystem
Mounting sysfs
Creating /dev
Starting udev
Loading scsi_mod.ko module
SCSI subsystem initialized
Loading sd_mod.ko module
Loading libata.ko module
Loading ata_piix.ko module
PCI: Obtained IRQ 20 for device 0000:00:1f.2
input: ImPS/2 Generic Wheel Mouse on isa0060/serio1
ata1: SATA max UDMA/133 cmd 0xFE00 ctl 0xFE12 bmdma 0xFEA0 irq 20
ata2: SATA max UDMA/133 cmd 0xFE20 ctl 0xFE32 bmdma 0xFEA8 irq 20
ata1: dev 0 ATA, max UDMA/133, 312500000 sectors: lba48
ata1: dev 0 configured for UDMA/133
scsi0 : ata_piix
ATA: abnormal status 0xFF on port 0xFE27
ata2: disabling port
scsi1 : ata_piix
  Vendor: ATA       Model: WDC WD1600JD-75H  Rev: 08.0
  Type:   Direct-Access                      ANSI SCSI revision: 05
SCSI device sda: 312500000 512-byte hdwr sectors (160000 MB)
SCSI device sda: drive cache: write back
SCSI device sda: 312500000 512-byte hdwr sectors (160000 MB)
SCSI device sda: drive cache: write back
 sda: sda1 sda2
Attached scsi disk sda at scsi0, channel 0, id 0, lun 0
Loading dm-mod.ko module
device-mapper: 4.4.0-ioctl (2005-01-12) initialised: dm-devel at redhat.com
Loading jbd.ko module
Loading ext3.ko module
Loading dm-mirror.ko module
Loading dm-zero.ko module
Loading dm-snapshot.ko module
Making device-mapper control node
Scanning logical volumes
File descriptor 3 left open
  Reading all physical volumes.  This may take a while...
cdrom: open failed.
cdrom: open failed.
  Found volume group "volume_01" using metadata type lvm2
Activating logical volumes
File descriptor 3 left open
  7 logical volume(s) in volume group "volume_01" now active
Making device nodes
File descriptor 3 left open
Creating root device
Mounting root filesystem
kjournald starting.  Commit interval 5 seconds
EXT3-fs: mounted filesystem with ordered data mode.
Switching to new root

  ***************************************************************
  ***************************************************************
  ** WARNING: Currently emulating unsupported memory accesses  **
  **          in /lib/tls libraries. The emulation is very     **
  **          slow, and may not work correctly with all        **
  **          programs (e.g., some may 'Segmentation fault').  **
  **          TO ENSURE FULL PERFORMANCE AND CORRECT FUNCTION, **
  **          YOU MUST EXECUTE THE FOLLOWING AS ROOT:          **
  **          mv /lib/tls /lib/tls.disabled                    **
  ***************************************************************
  ***************************************************************

Continuing...

security:  3 users, 5 roles, 589 types, 61 bools
security:  54 classes, 71803 rules
SELinux:  Completing initialization.
SELinux:  Setting up existing superblocks.
SELinux: initialized (dev dm-0, type ext3), uses xattr
SELinux: initialized (dev tmpfs, type tmpfs), uses transition SIDs
SELinux: initialized (dev selinuxfs, type selinuxfs), uses genfs_contexts
SELinux: initialized (dev mqueue, type mqueue), not configured for labeling
SELinux: initialized (dev hugetlbfs, type hugetlbfs), not configured for labeligSELinux: initialized (dev devpts, type devpts), uses transition SIDs
SELinux: initialized (dev eventpollfs, type eventpollfs), uses genfs_contexts
SELinux: initialized (dev tmpfs, type tmpfs), uses transition SIDs
SELinux: initialized (dev futexfs, type futexfs), uses genfs_contexts
SELinux: initialized (dev pipefs, type pipefs), uses task SIDs
SELinux: initialized (dev sockfs, type sockfs), uses task SIDs
SELinux: initialized (dev cpuset, type cpuset), not configured for labeling
SELinux: initialized (dev proc, type proc), uses genfs_contexts
SELinux: initialized (dev bdev, type bdev), uses genfs_contexts
SELinux: initialized (dev rootfs, type rootfs), uses genfs_contexts
SELinux: initialized (dev sysfs, type sysfs), uses genfs_contexts
INIT: version 2.85 booting
SELinux: initialized (dev usbfs, type usbfs), uses genfs_contexts
                Welcome to Fedora Core
                Press 'I' to enter interactive startup.
Starting udev:  [  OK  ]
Initializing hardware...  storage network audio done[  OK  ]
Setting clock  (utc): Wed Apr  6 16:52:30 BST 2005 [  OK  ]
Setting hostname animal.passback.co.uk:  [  OK  ]
Setting up Logical Volume Management: File descriptor 3 left open
  /var/lock: mkdir failed: Read-only file system
  7 logical volume(s) in volume group "volume_01" now active
[  OK  ]
Checking filesystems
Checking all file systems.
[/sbin/fsck.ext3 (1) -- /] fsck.ext3 -a /dev/volume_01/root
/dev/volume_01/root: clean, 18128/262144 files, 133030/262144 blocks
[/sbin/fsck.ext3 (1) -- /boot] fsck.ext3 -a /dev/sda1
/boot: clean, 65/263232 files, 24437/263056 blocks
[/sbin/fsck.ext3 (1) -- /export/backup] fsck.ext3 -a /dev/volume_01/backup
/dev/volume_01/backup: clean, 377040/10485760 files, 7569225/10485760 blocks
[/sbin/fsck.ext3 (1) -- /export/animal] fsck.ext3 -a /dev/volume_01/animal
/dev/volume_01/animal: clean, 17/5242880 files, 726262/10485760 blocks
[/sbin/fsck.ext3 (1) -- /tmp] fsck.ext3 -a /dev/volume_01/tmp
/dev/volume_01/tmp: clean, 541/262144 files, 34039/262144 blocks
[/sbin/fsck.ext3 (1) -- /usr] fsck.ext3 -a /dev/volume_01/usr
/dev/volume_01/usr: clean, 324735/5242880 files, 1768974/5242880 blocks
[/sbin/fsck.ext3 (1) -- /var] fsck.ext3 -a /dev/volume_01/var
/dev/volume_01/var: clean, 5263/1048576 files, 375637/1048576 blocks
[  OK  ]
Remounting root filesystem in read-write mode:  [  OK  ]
Mounting local filesystems:  [  OK  ]
Enabling local filesystem quotas:  [  OK  ]
Enabling swap space:  [  OK  ]
INIT: Entering runlevel: 5
Entering non-interactive startup
Starting sysstat:  Calling the system activity data collector (sadc):
[  OK  ]
Starting readahead_early:  Starting background readahead: [  OK  ]
Bringing up loopback interface:  [  OK  ]
Bringing up interface eth0:  [  OK  ]
Starting system logger: [  OK  ]
Starting kernel logger: [  OK  ]
Starting irqbalance: [  OK  ]
Starting portmap: [  OK  ]
Starting NFS statd: [  OK  ]
Starting auditd: [  OK  ]
Starting RPC idmapd: [  OK  ]
Mounting other filesystems:  [  OK  ]
Starting lm_sensors:  [  OK  ]
Starting automount: [  OK  ]
Starting nifd...
Starting mDNSResponder... [  OK  ]
Starting cups: [  OK  ]
Starting sshd: [  OK  ]
ip_tables: (C) 2000-2002 Netfilter core team
Starting xinetd: [  OK  ]
ntpd: Synchronizing with time server: Debug: sleeping function called from inva0in_atomic():1, irqs_disabled():0
 [<c01534a4>] __kmalloc+0x174/0x190
 [<c8867cce>] ata_interrupt+0xce/0x120 [libata]
 [<c01a8885>] proc_create+0xb5/0x130
 [<c01a89ef>] proc_mkdir_mode+0x2f/0x70
 [<c01a8a50>] proc_mkdir+0x20/0x30
 [<c0147d85>] register_handler_proc+0xc5/0xf0
 [<c01473be>] setup_irq+0xae/0x110
 [<c8945870>] e100_intr+0x0/0x1a0 [e100]
 [<c01476ba>] request_irq+0xaa/0xd0
 [<c8946865>] e100_up+0x125/0x250 [e100]
 [<c8945870>] e100_intr+0x0/0x1a0 [e100]
 [<c02e6880>] dev_watchdog+0x0/0xd0
 [<c02e6943>] dev_watchdog+0xc3/0xd0
 [<c0129f5e>] run_timer_softirq+0xee/0x1f0
 [<c0125204>] __do_softirq+0x84/0x110
 [<c0125309>] do_softirq+0x79/0x80
 [<c010e8c2>] do_IRQ+0x22/0x30
 [<c0106372>] evtchn_do_upcall+0x82/0xb0
 [<c010a441>] hypervisor_callback+0x31/0x3c
 [<c0107dce>] xen_idle+0x7e/0x160
 [<c0107ef1>] cpu_idle+0x41/0x60
[FAILED]
Starting ntpd: [  OK  ]
Starting sendmail: Debug: sleeping function called from invalid context at mm/s0in_atomic():1, irqs_disabled():0
 [<c01534a4>] __kmalloc+0x174/0x190
 [<c01a8885>] proc_create+0xb5/0x130
 [<c01a89ef>] proc_mkdir_mode+0x2f/0x70
 [<c01a8a50>] proc_mkdir+0x20/0x30
 [<c0147d85>] register_handler_proc+0xc5/0xf0
 [<c01473be>] setup_irq+0xae/0x110
 [<c8945870>] e100_intr+0x0/0x1a0 [e100]
 [<c01476ba>] request_irq+0xaa/0xd0
 [<c8946865>] e100_up+0x125/0x250 [e100]
 [<c8945870>] e100_intr+0x0/0x1a0 [e100]
 [<c02e6880>] dev_watchdog+0x0/0xd0
 [<c02e6943>] dev_watchdog+0xc3/0xd0
 [<c0129f5e>] run_timer_softirq+0xee/0x1f0
 [<c0125204>] __do_softirq+0x84/0x110
 [<c0125309>] do_softirq+0x79/0x80
 [<c010e8c2>] do_IRQ+0x22/0x30
 [<c0106372>] evtchn_do_upcall+0x82/0xb0
 [<c010a441>] hypervisor_callback+0x31/0x3c
 [<c0107dce>] xen_idle+0x7e/0x160
 [<c0107ef1>] cpu_idle+0x41/0x60
[  OK  ]
Starting sm-client: Debug: sleeping function called from invalid context at mm/0in_atomic():1, irqs_disabled():0
 [<c01534a4>] __kmalloc+0x174/0x190
 [<c8867cce>] ata_interrupt+0xce/0x120 [libata]
 [<c01a8885>] proc_create+0xb5/0x130
 [<c01a89ef>] proc_mkdir_mode+0x2f/0x70
 [<c01a8a50>] proc_mkdir+0x20/0x30
 [<c0147d85>] register_handler_proc+0xc5/0xf0
 [<c01473be>] setup_irq+0xae/0x110
 [<c8945870>] e100_intr+0x0/0x1a0 [e100]
 [<c01476ba>] request_irq+0xaa/0xd0
 [<c8946865>] e100_up+0x125/0x250 [e100]
 [<c8945870>] e100_intr+0x0/0x1a0 [e100]
 [<c02e6880>] dev_watchdog+0x0/0xd0
 [<c02e6943>] dev_watchdog+0xc3/0xd0
 [<c0129f5e>] run_timer_softirq+0xee/0x1f0
 [<c0125204>] __do_softirq+0x84/0x110
 [<c0125309>] do_softirq+0x79/0x80
 [<c010e8c2>] do_IRQ+0x22/0x30
 [<c0106372>] evtchn_do_upcall+0x82/0xb0
 [<c010a441>] hypervisor_callback+0x31/0x3c
 [<c0107dce>] xen_idle+0x7e/0x160
 [<c0107ef1>] cpu_idle+0x41/0x60
[  OK  ]
Starting crond: [  OK  ]
Starting xfs: [  OK  ]
Starting anacron: [  OK  ]
Starting atd: [  OK  ]
Starting readahead:  Starting background readahead: [  OK  ]
Starting system message bus: [  OK  ]
Starting cups-config-daemon: [  OK  ]
Starting HAL daemon: [  OK  ]
Debug: sleeping function called from invalid context at mm/slab.c:2090
in_atomic():1, irqs_disabled():0
 [<c01534a4>] __kmalloc+0x174/0x190
 [<c01a8885>] proc_create+0xb5/0x130
 [<c0118688>] try_to_wake_up+0x98/0x330
 [<c01a89ef>] proc_mkdir_mode+0x2f/0x70
 [<c01a8a50>] proc_mkdir+0x20/0x30
 [<c0147d85>] register_handler_proc+0xc5/0xf0
 [<c01473be>] setup_irq+0xae/0x110
 [<c8945870>] e100_intr+0x0/0x1a0 [e100]
 [<c01476ba>] request_irq+0xaa/0xd0
 [<c8946865>] e100_up+0x125/0x250 [e100]
 [<c8945870>] e100_intr+0x0/0x1a0 [e100]
 [<c02e6880>] dev_watchdog+0x0/0xd0
 [<c02e6943>] dev_watchdog+0xc3/0xd0
 [<c0129f5e>] run_timer_softirq+0xee/0x1f0
 [<c0125204>] __do_softirq+0x84/0x110
 [<c0125309>] do_softirq+0x79/0x80
 [<c010e8c2>] do_IRQ+0x22/0x30
 [<c0106372>] evtchn_do_upcall+0x82/0xb0
 [<c010a441>] hypervisor_callback+0x31/0x3c
 [<c0107dce>] xen_idle+0x7e/0x160
 [<c0107ef1>] cpu_idle+0x41/0x60

-------------- next part --------------
# grub.conf generated by anaconda
#
# Note that you do not have to rerun grub after making changes to this file
# NOTICE:  You have a /boot partition.  This means that
#          all kernel and initrd paths are relative to /boot/, eg.
#          root (hd0,0)
#          kernel /vmlinuz-version ro root=/dev/volume_01/root
#          initrd /initrd-version.img
#boot=/dev/sda
default=1
timeout=5
splashimage=(hd0,0)/grub/splash.xpm.gz
hiddenmenu
title Fedora Core (2.6.11-1.1226_FC4xen0)
	root (hd0,0)
	kernel /xen.gz dom0_mem=131072 com1=9600,8n1 console=com1
	module /vmlinuz-2.6.11-1.1226_FC4xen0 ro root=/dev/volume_01/root console=ttyS0
	module /initrd-2.6.11-1.1226_FC4xen0.img
title Fedora Core (2.6.11-1.1226_FC4smp)
	root (hd0,0)
	kernel /vmlinuz-2.6.11-1.1226_FC4smp ro root=/dev/volume_01/root rhgb quiet
	initrd /initrd-2.6.11-1.1226_FC4smp.img
title Fedora Core (2.6.11-1.1226_FC4) Single
	root (hd0,0)
	kernel /vmlinuz-2.6.11-1.1226_FC4 ro root=/dev/volume_01/root single
	initrd /initrd-2.6.11-1.1226_FC4.img


More information about the fedora-test-list mailing list