call for testing, dmraid in rawhide

Andy Burns fedora-test at adslpipe.co.uk
Sat Dec 31 12:59:23 UTC 2005


Peter Jones wrote:

> It's really best if you actually go and "delete" the raid volume before
> turning raid off in the BIOS, or else we'll still see the raid when we
> probe the disks.  without removing the metadata, it's also possible
> (though unlikely if you're keeping the disks on one controller/bios)
> that making another raid on the same drive will result in multiple sets
> of metadata on the disk.

OK, now that rawhide is bootable/installable again for me I have tried 
dmraid again.

With BIOS in SATA=AHCI mode I booted a rescue CD and did
dd if=/dev/zero of=/dev/sda
dd if=/dev/zero of=/dev/sdb

Then changed BIOS to SATA=RAID mode, rebooted went into the ICH7R option 
ROM and created two arrays (a 50GB RAID1 from 50GB of each disk and a 
400GB from the remaining 200GB of each disk)

Booted from rawhide 2005-12-31 with command line
linux dmraid vga=773 debug console=ttyS0,115200 console=tty1

Kernel boots and starts /sbin/loader
I choose language/dhcp/http install
Machine retrieves stage2.img, starts anaconda, starts X11
then immediately backtraces the same way as it did before
http://adslpipe.co.uk/dmraidtrace.jpg

I thought I'd bugzilla'ed this but apparently not ....

Linux version 2.6.14-1.1805_FC5 (bhcompile at ls20-bc1-13.build.redhat.com) 
(gcc version 4.1.0 20051222 (Red Hat 4.1.0-0.12)) #1 Fri Dec 30 16:18:48 
EST 2005
BIOS-provided physical RAM map:
  BIOS-e820: 0000000000000000 - 0000000000099000 (usable)
  BIOS-e820: 0000000000099000 - 00000000000a0000 (reserved)
  BIOS-e820: 00000000000e0000 - 0000000000100000 (reserved)
  BIOS-e820: 0000000000100000 - 000000003fe4c000 (usable)
  BIOS-e820: 000000003fe4c000 - 000000003fe56000 (ACPI NVS)
  BIOS-e820: 000000003fe56000 - 000000003fe88000 (usable)
  BIOS-e820: 000000003fe88000 - 000000003fee9000 (ACPI NVS)
  BIOS-e820: 000000003fee9000 - 000000003feed000 (usable)
  BIOS-e820: 000000003feed000 - 000000003feff000 (ACPI data)
  BIOS-e820: 000000003feff000 - 000000003ff00000 (usable)
127MB HIGHMEM available.
896MB LOWMEM available.
found SMP MP-table at 000fe680
Using x86 segment limits to approximate NX protection
On node 0 totalpages: 261888
   DMA zone: 4096 pages, LIFO batch:0
   DMA32 zone: 0 pages, LIFO batch:0
   Normal zone: 225280 pages, LIFO batch:31
   HighMem zone: 32512 pages, LIFO batch:7
DMI 2.3 present.
ACPI: RSDP (v000 INTEL                                 ) @ 0x000fe020
ACPI: RSDT (v001 INTEL  D945GTP  0x00000ca7 MSFT 0x01000013) @ 0x3fefde48
ACPI: FADT (v001 INTEL  D945GTP  0x00000ca7 MSFT 0x01000013) @ 0x3fefcf10
ACPI: MADT (v001 INTEL  D945GTP  0x00000ca7 MSFT 0x01000013) @ 0x3fefce10
ACPI: WDDT (v001 INTEL  D945GTP  0x00000ca7 MSFT 0x01000013) @ 0x3fef7f90
ACPI: MCFG (v001 INTEL  D945GTP  0x00000ca7 MSFT 0x01000013) @ 0x3fef7f10
ACPI: HPET (v001 INTEL  D945GTP  0x00000ca7 MSFT 0x01000013) @ 0x3fef7e90
ACPI: SSDT (v001 INTEL     CpuPm 0x00000ca7 MSFT 0x01000013) @ 0x3fefdc10
ACPI: SSDT (v001 INTEL   Cpu0Ist 0x00000ca7 MSFT 0x01000013) @ 0x3fefda10
ACPI: SSDT (v001 INTEL   Cpu1Ist 0x00000ca7 MSFT 0x01000013) @ 0x3fefd810
ACPI: SSDT (v001 INTEL   Cpu2Ist 0x00000ca7 MSFT 0x01000013) @ 0x3fefd610
ACPI: SSDT (v001 INTEL   Cpu3Ist 0x00000ca7 MSFT 0x01000013) @ 0x3fefd410
ACPI: DSDT (v001 INTEL  D945GTP  0x00000ca7 MSFT 0x01000013) @ 0x00000000
ACPI: PM-Timer IO Port: 0x408
ACPI: Local APIC disabled (-2); pass 'lapic' to re-enable.
ACPI: HPET id: 0x8086a201 base: 0xfed00000
LAPIC disabled (-2)
Allocating PCI resources starting at 40000000 (gap: 3ff00000:c0100000)
Built 1 zonelists
Kernel command line: initrd=initrd.img ramdisk_size=8192 
BOOT_IMAGE=vmlinuz dmraid vga=773 debug console=ttyS0,115200 console=tty1
mapped APIC to ffffd000 (00000000)
Initializing CPU#0
CPU 0 irqstacks, hard=c03c2000 soft=c03c1000
PID hash table entries: 4096 (order: 12, 65536 bytes)
Console: colour dummy device 80x25
Dentry cache hash table entries: 131072 (order: 7, 524288 bytes)
Inode-cache hash table entries: 65536 (order: 6, 262144 bytes)
Memory: 1029396k/1047552k available (1875k kernel code, 16968k reserved, 
745k data, 172k init, 129548k highmem)
Checking if this processor honours the WP bit even in supervisor mode... Ok.
Using HPET for base-timer
Using HPET for gettimeofday
Detected 3000.152 MHz processor.
Using hpet for high-res timesource
Calibrating delay using timer specific routine.. 6005.15 BogoMIPS 
(lpj=12010302)
Security Framework v1.0.0 initialized
SELinux:  Initializing.
SELinux:  Starting in permissive mode
selinux_register_security:  Registering secondary module capability
Capability LSM initialized as secondary
Mount-cache hash table entries: 512
CPU: After generic identify, caps: bfebfbff 20100000 00000000 00000000 
0000649d 00000000 00000000
CPU: After vendor identify, caps: bfebfbff 20100000 00000000 00000000 
0000649d 00000000 00000000
monitor/mwait feature present.
using mwait in idle threads.
CPU: Trace cache: 12K uops, L1 D cache: 16K
CPU: L2 cache: 2048K
CPU: After all inits, caps: bfebf3ff 20100000 00000000 00000080 0000649d 
00000000 00000000
Intel machine check architecture supported.
Intel machine check reporting enabled on CPU#0.
CPU0: Intel P4/Xeon Extended MCE MSRs (24) available
mtrr: v2.0 (20020519)
CPU: Intel(R) Pentium(R) 4 CPU 3.00GHz stepping 03
Enabling fast FPU save and restore... done.
Enabling unmasked SIMD FPU exception support... done.
Checking 'hlt' instruction... OK.
ACPI: setting ELCR to 0200 (from 0e00)
Local APIC disabled by default; use 'lapic' to enable it.
checking if image is initramfs... it is
Freeing initrd memory: 4651k freed
NET: Registered protocol family 16
ACPI: bus type pci registered
PCI: Using MMCONFIG
ACPI: Subsystem revision 20050902
ACPI: Interpreter enabled
ACPI: Using PIC for interrupt routing
ACPI: PCI Root Bridge [PCI0] (0000:00)
PCI: Probing PCI hardware (bus 00)
ACPI: Assume root bridge [\_SB_.PCI0] bus is 0
PCI: Ignoring BAR0-3 of IDE controller 0000:00:1f.1
Boot video device is 0000:01:00.0
PCI: Transparent bridge - 0000:00:1e.0
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0._PRT]
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.P32_._PRT]
ACPI: PCI Interrupt Link [LNKA] (IRQs 3 4 5 7 9 10 *11 12)
ACPI: PCI Interrupt Link [LNKB] (IRQs 3 4 5 7 9 10 *11 12)
ACPI: PCI Interrupt Link [LNKC] (IRQs 3 4 5 7 9 10 *11 12)
ACPI: PCI Interrupt Link [LNKD] (IRQs 3 4 5 7 9 10 *11 12)
ACPI: PCI Interrupt Link [LNKE] (IRQs 3 4 5 7 9 10 *11 12)
ACPI: PCI Interrupt Link [LNKF] (IRQs 3 4 5 7 9 10 *11 12)
ACPI: PCI Interrupt Link [LNKG] (IRQs 3 4 5 7 *9 10 11 12)
ACPI: PCI Interrupt Link [LNKH] (IRQs 3 4 5 7 9 *10 11 12)
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.PEX0._PRT]
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.PEX2._PRT]
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.PEX3._PRT]
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.PEX4._PRT]
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.PEX5._PRT]
Linux Plug and Play Support v0.97 (c) Adam Belay
pnp: PnP ACPI init
pnp: PnP ACPI: found 12 devices
usbcore: registered new driver usbfs
usbcore: registered new driver hub
PCI: Using ACPI for IRQ routing
PCI: If a device doesn't work, try "pci=routeirq".  If it helps, post a 
report
pnp: 00:05: ioport range 0x500-0x53f has been reserved
pnp: 00:05: ioport range 0x400-0x47f could not be reserved
pnp: 00:05: ioport range 0x680-0x6ff has been reserved
PCI: Bridge: 0000:00:01.0
   IO window: 2000-2fff
   MEM window: 50100000-501fffff
   PREFETCH window: 40000000-4fffffff
PCI: Bridge: 0000:00:1c.0
   IO window: disabled.
   MEM window: 50300000-503fffff
   PREFETCH window: disabled.
PCI: Bridge: 0000:00:1c.2
   IO window: disabled.
   MEM window: 50400000-504fffff
   PREFETCH window: disabled.
PCI: Bridge: 0000:00:1c.3
   IO window: disabled.
   MEM window: 50500000-505fffff
   PREFETCH window: disabled.
PCI: Bridge: 0000:00:1c.4
   IO window: disabled.
   MEM window: 50600000-506fffff
   PREFETCH window: disabled.
PCI: Bridge: 0000:00:1c.5
   IO window: disabled.
   MEM window: 50700000-507fffff
   PREFETCH window: disabled.
PCI: Bridge: 0000:00:1e.0
   IO window: 1000-1fff
   MEM window: 50000000-500fffff
   PREFETCH window: disabled.
ACPI: PCI Interrupt Link [LNKA] enabled at IRQ 11
PCI: setting IRQ 11 as level-triggered
ACPI: PCI Interrupt 0000:00:01.0[A] -> Link [LNKA] -> GSI 11 (level, 
low) -> IRQ 11
PCI: Setting latency timer of device 0000:00:01.0 to 64
ACPI: PCI Interrupt Link [LNKB] enabled at IRQ 11
ACPI: PCI Interrupt 0000:00:1c.0[A] -> Link [LNKB] -> GSI 11 (level, 
low) -> IRQ 11
PCI: Setting latency timer of device 0000:00:1c.0 to 64
ACPI: PCI Interrupt Link [LNKC] enabled at IRQ 11
ACPI: PCI Interrupt 0000:00:1c.2[C] -> Link [LNKC] -> GSI 11 (level, 
low) -> IRQ 11
PCI: Setting latency timer of device 0000:00:1c.2 to 64
ACPI: PCI Interrupt Link [LNKD] enabled at IRQ 11
ACPI: PCI Interrupt 0000:00:1c.3[D] -> Link [LNKD] -> GSI 11 (level, 
low) -> IRQ 11
PCI: Setting latency timer of device 0000:00:1c.3 to 64
ACPI: PCI Interrupt 0000:00:1c.4[A] -> Link [LNKB] -> GSI 11 (level, 
low) -> IRQ 11
PCI: Setting latency timer of device 0000:00:1c.4 to 64
ACPI: PCI Interrupt 0000:00:1c.5[B] -> Link [LNKA] -> GSI 11 (level, 
low) -> IRQ 11
PCI: Setting latency timer of device 0000:00:1c.5 to 64
PCI: Setting latency timer of device 0000:00:1e.0 to 64
apm: BIOS version 1.2 Flags 0x03 (Driver version 1.16ac)
apm: overridden by ACPI.
audit: initializing netlink socket (disabled)
audit(1136014555.364:1): initialized
highmem bounce pool size: 64 pages
Total HugeTLB memory allocated, 0
VFS: Disk quotas dquot_6.5.1
Dquot-cache hash table entries: 1024 (order 0, 4096 bytes)
SELinux:  Registering netfilter hooks
Initializing Cryptographic API
ksign: Installing public key data
Loading keyring
- Added public key 2729C55A2615442C
- User ID: Red Hat, Inc. (Kernel Module GPG key)
io scheduler noop registered
io scheduler anticipatory registered
io scheduler deadline registered
io scheduler cfq registered
ACPI: PCI Interrupt 0000:00:01.0[A] -> Link [LNKA] -> GSI 11 (level, 
low) -> IRQ 11
PCI: Setting latency timer of device 0000:00:01.0 to 64
assign_interrupt_mode Found MSI capability
Allocate Port Service[pcie00]
Allocate Port Service[pcie03]
ACPI: PCI Interrupt 0000:00:1c.0[A] -> Link [LNKB] -> GSI 11 (level, 
low) -> IRQ 11
PCI: Setting latency timer of device 0000:00:1c.0 to 64
assign_interrupt_mode Found MSI capability
Allocate Port Service[pcie00]
Allocate Port Service[pcie02]
Allocate Port Service[pcie03]
ACPI: PCI Interrupt 0000:00:1c.2[C] -> Link [LNKC] -> GSI 11 (level, 
low) -> IRQ 11
PCI: Setting latency timer of device 0000:00:1c.2 to 64
assign_interrupt_mode Found MSI capability
Allocate Port Service[pcie00]
Allocate Port Service[pcie02]
Allocate Port Service[pcie03]
ACPI: PCI Interrupt 0000:00:1c.3[D] -> Link [LNKD] -> GSI 11 (level, 
low) -> IRQ 11
PCI: Setting latency timer of device 0000:00:1c.3 to 64
assign_interrupt_mode Found MSI capability
Allocate Port Service[pcie00]
Allocate Port Service[pcie02]
Allocate Port Service[pcie03]
ACPI: PCI Interrupt 0000:00:1c.4[A] -> Link [LNKB] -> GSI 11 (level, 
low) -> IRQ 11
PCI: Setting latency timer of device 0000:00:1c.4 to 64
assign_interrupt_mode Found MSI capability
Allocate Port Service[pcie00]
Allocate Port Service[pcie02]
Allocate Port Service[pcie03]
ACPI: PCI Interrupt 0000:00:1c.5[B] -> Link [LNKA] -> GSI 11 (level, 
low) -> IRQ 11
PCI: Setting latency timer of device 0000:00:1c.5 to 64
assign_interrupt_mode Found MSI capability
Allocate Port Service[pcie00]
Allocate Port Service[pcie02]
Allocate Port Service[pcie03]
vesafb: framebuffer at 0x40000000, mapped to 0xf8880000, using 1536k, 
total 16384k
vesafb: mode is 1024x768x8, linelength=1024, pages=20
vesafb: protected mode interface info at c000:58b6
vesafb: scrolling: redraw
vesafb: Pseudocolor: size=8:8:8:8, shift=0:0:0:0
vesafb: Mode is VGA compatible
Console: switching to colour frame buffer device 128x48
fb0: VESA VGA frame buffer device
isapnp: Scanning for PnP cards...
isapnp: No Plug & Play device found
Real Time Clock Driver v1.12
PNP: PS/2 Controller [PNP0303:PS2K,PNP0f03:PS2M] at 0x60,0x64 irq 1,12
serio: i8042 AUX port at 0x60,0x64 irq 12
serio: i8042 KBD port at 0x60,0x64 irq 1
Serial: 8250/16550 driver $Revision: 1.90 $ 2 ports, IRQ sharing enabled
ÿserial8250: ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A
00:09: ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A
RAMDISK driver initialized: 16 RAM disks of 8192K size 1024 blocksize
Uniform Multi-Platform E-IDE driver Revision: 7.00alpha2
ide: Assuming 33MHz system bus speed for PIO modes; override with idebus=xx
ICH7: IDE controller at PCI slot 0000:00:1f.1
ACPI: PCI Interrupt 0000:00:1f.1[A] -> Link [LNKC] -> GSI 11 (level, 
low) -> IRQ 11
ICH7: chipset revision 1
ICH7: not 100% native mode: will probe irqs later
     ide0: BM-DMA at 0x30b0-0x30b7, BIOS settings: hda:DMA, hdb:pio
Probing IDE interface ide0...
hda: LITE-ON DVDRW LDW-411S, ATAPI CD/DVD-ROM drive
ide0 at 0x1f0-0x1f7,0x3f6 on irq 14
Probing IDE interface ide1...
hda: ATAPI 32X DVD-ROM CD-R/RW drive, 2048kB Cache, UDMA(33)
Uniform CD-ROM driver Revision: 3.20
ide-floppy driver 0.99.newide
usbcore: registered new driver libusual
usbcore: registered new driver hiddev
usbcore: registered new driver usbhid
drivers/usb/input/hid-core.c: v2.6:USB HID core driver
mice: PS/2 mouse device common for all mice
md: md driver 0.90.3 MAX_MD_DEVS=256, MD_SB_DISKS=27
md: bitmap version 4.39
NET: Registered protocol family 2
input: AT Translated Set 2 keyboard as /class/input/input0
IP route cache hash table entries: 32768 (order: 5, 131072 bytes)
TCP established hash table entries: 131072 (order: 9, 2097152 bytes)
TCP bind hash table entries: 65536 (order: 8, 1310720 bytes)
TCP: Hash tables configured (established 131072 bind 65536)
TCP reno registered
TCP bic registered
Initializing IPsec netlink socket
NET: Registered protocol family 1
NET: Registered protocol family 17
Using IPI Shortcut mode
ACPI wakeup devices:
SLPB  P32 UAR1 PEX0 PEX1 PEX2 PEX3 PEX4 PEX5 UHC1 UHC2 UHC3 UHC4 EHCI 
AC9M AZAL
ACPI: (supports S0 S1 S3 S4 S5)
Freeing unused kernel memory: 172k freed
Write protecting the kernel read-only data: 318k






More information about the fedora-test-list mailing list