Kernel-2.6.15-1.1863_FC5 and udev-078-4, kernel oopses.
Kimmo Koivisto
kimmo.koivisto at surfeu.fi
Sun Jan 22 11:47:50 UTC 2006
Hello
I have FC5t2 (updated from t1 with yum) and I have problems booting with
kernel-2.6.15-1.1863_FC5. I cannot boot, kernel oopses. I recorded it with
serial console, see attached file.
I don't have problems with kernel-2.6.15-1.1826.2.9_FC5.
Any ideas?
Regards
Kimmo Koivisto
-------------- next part --------------
Linux version 2.6.15-1.1863_FC5 (bhcompile at ls20-bc1-13.build.redhat.com) (gcc ve
rsion 4.1.0 20060117 (Red Hat 4.1.0-0.15)) #1 Thu Jan 19 19:17:58 EST 2006
BIOS-provided physical RAM map:
BIOS-e820: 0000000000000000 - 00000000000a0000 (usable)
BIOS-e820: 00000000000f0000 - 0000000000100000 (reserved)
BIOS-e820: 0000000000100000 - 000000001fff0000 (usable)
BIOS-e820: 000000001fff0000 - 000000001fff3000 (ACPI NVS)
BIOS-e820: 000000001fff3000 - 0000000020000000 (ACPI data)
BIOS-e820: 00000000fec00000 - 00000
BIOS-e820: 00000000fee00000 - 00000000fee01000 (reserved)
BIOS-e820: 00000000ffff0000 - 0000000100000000 (reserved)
0MB HIGHMEM available.
511MB LOWMEM available.
Using x86 segment limits to approximate NX protection
DMI 2.2 present.
ACPI: PM-Timer IO Port: 0x4008
ACPI: Local APIC disabled (-2); pass 'lapic' to re-enable.
Allocating PCI resources starting at 30000000 (gap: 20000000:dec00000)
Built 1 zonelists
Kernel command line: ro root=LABEL=/ console=ttyS0,115200n8 console=tty
Enabling fast FPU save and rest
Enabling unmasked SIMD FPU exception support... done.
Initializing CPU#0
CPU 0 irqstacks, hard=c03d8000 soft=c03d7000
PID hash table entries: 2048 (order: 11, 32768 bytes)
Detected 1670.785 MHz processor.
Using pmtmr for high-res timesource
Console: colour VGA+ 80x25
Dentry cache hash table entries: 131072 (order: 7, 524288 bytes)
Inode-cache hash table entries: 65536 (order: 6, 262144 bytes)
Memory: 514700k/524224k available (1929k kernel code, 9008k reserved, 777k data,
176k init, 0k highmem)
Checking if this processor honours the WP bit even in supervisor mode... Ok.
Calibrating delay using timer specific routine.. 3346.04 BogoMIPS (lpj=6692090)
Security Framework v1.0.0 initialized
SELinux: Initializing.
SELinux: Starting in permissive mode
selinux_register_security: Registering secondary module capability
Capability LSM initialized as secondary
Mount-cache hash table entries: 512
CPU: L1 I Cache: 64K (64 bytes/line), D cache 64K (64 bytes/line)
CPU: L2 Cache: 256K (64 bytes/line)
Intel machine check architecture supported.
Intel machine check reporting enabled on CPU#0.
mtrr: v2.0 (20020519)
CPU: AMD Athlon(tm) XP 2000+ stepping 02
Checking 'hlt' instruction... OK.
ACPI: setting ELCR to 0200 (from 1e20)
checking if image is initramfs... it is
Freeing initrd memory: 767k freed
NET: Registered protocol family 16
ACPI: bus type pci registered
PCI: PCI BIOS revision 2.10 entry at 0xfb3b0, last bus=2
PCI: Using configuration type 1
ACPI: Subsystem revision 20050902
ACPI: Interpreter enabled
ACPI: Using PIC for interrupt routing
ACPI: PCI Root Bridge [PCI0] (0000:00)
ACPI: Assume root bridge [\_SB_.PCI0] bus is 0
PCI quirk: region 4000-407f claimed by vt8235 PM
PCI quirk: region 5000-500f claimed by vt8235 SMB
ACPI: PCI Interrupt Link [LNKA] (IRQs 1 3 4 5 6 7 10 *11 12 14 15)
ACPI: PCI Interrupt Link [LNKB] (IRQs 1 3 4 *5 6 7 10 11 12 14 15)
ACPI: PCI Interrupt Link [LNKC] (IRQs 1 3 4 5 6 7 *10 11 12 14 15)
ACPI: PCI Interrupt Link [LNKD] (IRQs 1 3 4 5 6 7 10 11 *12 14 15)
ACPI: PCI Interrupt Link [ALKA] (IRQs 20) *0, disabled.
ACPI: PCI Interrupt Link [ALKB] (IRQs 21) *0, disabled.
ACPI: PCI Interrupt Link [ALKC] (IRQs 22) *0, disabled.
ACPI: PCI Interrupt Link [ALKD] (IRQs 23) *0, disabled.
Linux Plug and Play Support v0.97 (c) Adam Belay
pnp: PnP ACPI init
pnp: PnP ACPI: found 13 devices
usbcore: registered new driver usbfs
usbcore: registered new driver hub
PCI: Using ACPI for IRQ routing
PCI: If a device doesn't work, try "pci=routeirq". If it helps, post a report
pnp: 00:01: ioport range 0x4000-0x407f could not be reserved
pnp: 00:01: ioport range 0x5000-0x500f has been reserved
PCI: Bridge: 0000:00:01.0
IO window: 9000-9fff
MEM window: e0000000-e1ffffff
PREFETCH window: d8000000-dfffffff
PCI: Bus 2, cardbus bridge: 0000:00:0a.0
IO window: 00001000-000010ff
IO window: 00001400-000014ff
PREFETCH window: 30000000-31ffffff
MEM window: 32000000-33ffffff
ACPI: PCI Interrupt Link [LNKC] enabled at IRQ 10
ACPI: PCI Interrupt 0000:00:0a.0[A] -> Link [LNKC] -> GSI 10
10
apm: BIOS version 1.2 Flags 0x07 (Driver version 1.16ac)
apm: overridden by ACPI.
audit: initializing netlink socket (disabled)
audit(1137936050.676:1): initialized
Total HugeTLB memory allocated, 0
VFS: Disk quotas dquot_6.5.1
Dquot-cache hash table entries: 1024 (order 0, 4096 bytes)
SELinux: Registering netfilter hooks
Initializing Cryptographic API
ksign: Installing public key data
Loading keyring
- Added public key 8928DF366D0286DA
- User ID: Red Hat, Inc. (Kernel Module GPG key)
io scheduler noop regist
io scheduler anticipatory registered
io scheduler deadline registered
io scheduler cfq registered
pci_hotplug: PCI Hot Plug PCI Core version: 0.5
ACPI: Fan [FAN] (on)
ACPI: CPU0 (power states: C1[C1] C2[C2])
ACPI: Thermal Zone [THRM] (43 C)
isapnp: Scanning for PnP cards...
isapnp: No Plug & Play device found
Real Time Clock Driver v1.12ac
Linux agpgart interface v0.101 (c) Dave Jones
agpgart: Detected VIA KT400/KT400A/KT600 chipset
agpgart: AGP aperture is 128M @ 0xd0000000
PNP: PS/2 Controller [PNP0303:PS2K] at
PNP: PS/2 controller doesn't have AUX irq; using default 12
serio: i8042 AUX port at 0x60,0x64 irq 12
serio: i8042 KBD port at 0x60,0x64 irq 1
Serial: 8250/16550 driver $Revision: 1.90 $ 2 ports, IRQ sharing enabled
ÿserial8250: ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A
serial8250: ttyS1 at I/O 0x2f8 (irq = 3) is a 16550A
00:08: ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A
00:09: ttyS1 at I/O 0x2f8 (irq = 3) is a 16550A
RAMDISK driver initialized: 16 RAM disks of 16384K size 1024 blocksize
Uniform Multi-Platform E-IDE driver Revision: 7.00alpha2
ide: Assuming 33MHz system bus speed for PIO modes; override with idebus=xx
VP_IDE: IDE controller at PCI slot 0000:00:11.1
ACPI: PCI Interrupt Link [LNKA] enabled at IRQ 11
ACPI: PCI Interrupt 0000:00:11.1[A] -> Link [LNKA] -> GSI 11 (level, low) -> IRQ
11
PCI: Via IRQ fixup for 0000:00:11.1, from 255 to 11
VP_IDE: chipset revision 6
VP_IDE: not 100% native mode: will probe irqs later
VP_IDE: VIA vt8235 (rev 00) IDE UDMA133 controller on pci0000:00:11.1
ide0: BM-DMA at 0xbc00-0xbc07, BIOS settings: hda:DMA, hdb:pio
ide1: BM-DMA at 0xbc08-0xbc0f, BIOS settings: hdc:DMA, hdd:DMA
hda: SAMSUNG SP8004H, ATA DISK drive
ide0 at 0x1f0-0x1f7,0x3f6 on irq 14
hdc: SAMSUNG CD-R/RW SW-252B, ATAPI CD/DVD-ROM drive
hdd: ATAPI DVD DUAL 8X4X12, ATAPI CD/DVD-ROM drive
ide1 at 0x170-0x177,0x376 on irq 15
hda: max request size: 128KiB
hda: 156368016 sectors (80060 MB) w/2048KiB Cache, CHS=65535/16/63, UDMA(100)
hda: cache flushes supported
hda: hda1 hda2
hdc: ATAPI 52X CD-ROM CD-R/RW drive, 2048kB Cache, UDMA(33)
Uniform CD-ROM driver Revision: 3.20
hdd: ATAPI 40X DVD-ROM DVD-R CD-R/RW drive, 8192kB Cache, UDMA(33)
ide-floppy driver 0.99.newide
ACPI: PCI Interrupt 0000:00:0a.0[A] -> Link [LNKC] -> GSI 10 (level, low) -> IRQ
10 Yenta: CardBus bridge found at 0000:00:0a.0 [1154:030a] Yenta: ISA IRQ mask 0x0000, PCI irq 10
Socket status: 30000810 usbcore: registered new driver libusual usbcore: registered new driver hiddev
usbcore: registered new driver usbhid drivers/usb/input/hid-core.c: v2.6:USB HID core driver
mice: PS/2 mouse device common for all mice md: md driver 0.90.3 MAX_MD_DEVS=256, MD_SB_DISKS=27
md: bitmap version 4.39 NET: Registered protocol family 2 IP route cache hash table
entries: 8192 (order: 3, 32768 bytes) TCP established hash table entries: 32768 (order: 7, 524288 bytes)
TCP bind hash table entries: 32768 (order: 7, 655360 bytes) TCP: Hash tables configured (established 32768 bind 32768)
TCP reno registered TCP bic registered Initializing IPsec NET: Registered protocol family 1 NET: Registered protocol family 17
powernow-k8: Processor cpuid 662 not supported Using IPI Shortcut mode ACPI wakeup devices: PCI0 USB0 USB1 USB2 USB6 USB7 USB8
USB9 LAN0 UAR1 LPT1 ACPI: (supports S0 S1 S4 S5) Freeing unused kernel memory: 176k freed Write protecting the kernel read-only
data: 356k input: AT Translated Set 2 keyboard as /class/input/input0 kjournald starting. Commit interval 5 seconds
EXT3-fs: mounted filesystem with ordered data mode. pccard: PCMCIA card inser SELinux: Disabled at runtime.
SELinux: Unregistering netfilter hooks Unable to handle kernel NULL pointer dereference at virtual address 000000fc
printing eip: *pde = 1ef5b067
Oops: 0002 [#1]
last sysfs file: /devices/pci0000:00/0000:00:11.5/modalias
Modules linked in: parport_pc parport floppy nvram orinoco_cs orinoco hermes hos
tap_cs hostap ieee80211_crypt stradis compat_ioctl32 ehci_hcd ohci1394 ieee1394
uhci_hcd snd_via82xx gameport snd_ac97_codec snd_ac97_bus snd_seq_dummy snd_seq_
oss snd_seq_midi_event snd_seq snd_pcm_oss snd_mixer_oss dvb_ttpci l64781 saa714
6_vv snd_pcm video_buf saa7146 v4l1_compat snd_timer v4l2_common snd_page_alloc
videodev ves1820 snd_mpu401_uart snd_rawmidi i2c_viapro stv0299 snd_seq_device v
ia_ircc dvb_core tda8083 snd irda stv0297 sp8870 ves1x93 ttpci_eeprom i2c_core v
ia_rhine mii soundcore crc_ccitt ext3 jbd
CPU: 0
EIP: 0060:[<e09ed182>] Not tainted VLI
EFLAGS: 00010246 (2.6.15-1.1863_FC5)
EIP is at stradis_probe+0x5ba/0xa81 [stradis]
eax: 00000000 ebx: e09f20e0 ecx: 00000000 edx: df23ccf0
esi: e09f1b2c edi: e09f2540 ebp: e09f20e0 esp: df074d70
ds: 007b es: 007b ss: 0068
Process modprobe (pid: 899, threadinfo=df074000 task=df23ccf0)
Stack: <0>dfcf607c 00000000 00000000 00000001 dead4ead ffffffff ffffffff 0000000
1
dead4ead ffffffff ffffffff 00000001 dead4ead ffffffff ffffffff 00000001
dead4ead ffffffff ffffffff 00000001 dead4ead ffffffff ffffffff e09f190c
Call Trace:
[<c02284b0>] __driver_attach+0x0/0x8b [<c
57
[<c02283fd>] driver_probe_device+0x42/0x8b [<c0228513>] __driver_attach+0x6
3/0x8b
[<c0227ef9>] bus_for_each_dev+0x33/0x55 [<c0228361>] driver_attach+0x11/0x1
3
[<c02284b0>] __driver_attach+0x0/0x8b [<c0227c1a>] bus_add_driver+0x64/0xfd
[<c01cd709>] __pci_register_driver+0x82/0xa4 [<e09c201a>] stradis_init+0x1a
/0x2f [stradis]
[<c0131c95>] sys_init_module+0x137c/0x150e [<e09e1000>] ieee80211_crypt_nul
l_init+0x0/0x6 [ieee80211_crypt]
[<c01547df>] do_sync_read+0xb8/0xf3 [<c012a963
x0/0x2d
[<c02df797>] __mutex_unlock_slowpath+0x1c3/0x1c8 [<c0154727>] do_sync_read+
0x0/0xf3
[<c01550a9>] vfs_read+0x9f/0x13e [<c0155410>] sys_read+0x3c/0x63
[<c0102ba9>] syscall_call+0x7/0xb <0>Code: c4 10 e9 df 04 00 00 8b 04 24 8b
98 74 01 00 00 31 c0 b9 18 01 00 00 89 df f3 ab c7 83 7c 02 00 00 00 00 00 00 8b
83 0c 03 00 00 <c7> 80 fc 00 00 00 00 00 ff ff b8 00 f0 ff ff 21 e0 f7 40 14 00
Continuing in 1 seconds.
<1>Unable to handle kernel NULL pointer dereference at virtual address 00000000
printing eip:
c0188fff
*pde = 1edf3067
Oops: 0000 [#2]
last sysfs file: /devices/pci0000:00/0000:00:11.5/modalias
Modules linked in: parport_pc parport floppy nvram orinoco_cs orinoco hermes hos
tap_cs hostap ieee80211_crypt stradis compat_ioctl32 ehci_hcd ohci1394 ieee1394
uhci_hcd snd_via82xx gameport snd_ac97_codec snd_ac97_bus snd_seq_dummy snd_seq_
oss snd_seq_midi_event snd_seq snd_pcm_oss snd_mixer_oss dvb_ttpci l64781 saa714
6_vv snd_pcm video_buf saa7146 v4l1_compat snd_timer v4l2_common snd_page_allo
videodev ves1820 snd_mpu401_uart snd_rawmidi i2c_viapro stv0299 snd_seq_device v
ia_ircc dvb_core tda8083 snd irda stv0297 sp8870 ves1x93 ttpci_eeprom i2c_core v
ia_rhine mii soundcore crc_ccitt ext3 jbd
CPU: 0
EIP: 0060:[<c0188fff>] Not tainted VLI
EFLAGS: 00010246 (2.6.15-1.1863_FC5)
EIP is at sysfs_lookup+0x30/0x1ac
eax: 00000000 ebx: dee9a1e0 ecx: df0d5f10 edx: 00000004
esi: 00000000 edi: dee9a250 ebp: ded19348 esp: df0d5dd8
ds: 007b es: 007b ss: 0068
Process udevd (pid: 1227, threadinfo=df0d5000 task=df13f1f0)
Stack: <0>ded1937c ffffffff c034b840 dee9a1e0 df272b80 df272c00 c015fe39 df0d5e5
0
df0d5e44 df0d5f10 dffe5be0 baf3f719 df272b80 ded5101e df0d5f10 c016198f
00000000 ded51024 00000000 00000000 00000000 000200d2 c0347ce8 00000000
Call Trace:
[<c015fe39>] do_lookup+0xb2/0x14d
[<c016198f>] __link_path_walk+0x821/0xc65 [<c0161e1a>] link_path_walk+0x47/
0xb9
[<c01621bc>] do_path_lookup+0x1ee/0x228 [<c01628ea>] __user_walk_fd+0x29/0x
3a
[<c015c888>] vfs_lstat_fd+0x12/0x39 [<c015c8f4>] sys_lstat64+0xf/0x23
[<c02e0ec8>] do_page_fault+0x189/0x51d [<c02e0d3f>] do_page_fault+0x0/0x51d
[<c0102ba9>] syscall_call+0x7/0xb <0>Code: ec 08 89 d3 8b 42 24 8b 40 60 89
04 24 8b 68 0c e9 6c 01 00 00 f6 45 18 2c 0f 84 5f 01 00 00 89 e8 e8 ca ed ff ff
89 c6 8b 7b 30 <ac> ae 75 08 84 c0 75 f8 31 c0 eb 04 19 c0 0c 01 85 c0 0f 85 3b
Continuing in 1 seconds.
BUG: udevd/1227, lock held at task exit time!
[df272c00] {inode_init_once}
.. held by: udevd: 1227 [df13f1f0, 118]
... acquired at: do_lookup+0x78/0x14d
usb 1-2: new high speed USB device using ehci_hcd and address 3
usb 1-2: configuration #1 chosen from 1 choice
hub 1-2:1.0: USB hub found
hub 1-2:1.0: 4 ports detected
ieee1394: Host added: ID:BUS[0-00:1023] GUID[0000d100808e7e2e]
usb 1-2.4: new high speed USB device using ehci_hcd and address 5
usb 1-2.4: configuration #1 chosen from 1 choice
SCSI subsystem initialized
Initializing USB Mass Storage driver...
scsi0 : SCSI emulation for USB Mass Storage devices
usb-storage: device found at 5
usb-storage: waiting for device to settle before scanning
usbcore: registered new driver usb-storage
USB Mass Storage support registered.
Vendor: Generic Model: CF Rev: 1.6E
Type: Direct-Access ANSI SCSI revision: 00
Vendor: Generic Model: MS Rev: 1.6E
Type: Direct-Access ANSI SCSI revision: 00
Vendor: Generic Model: MMC/SD Rev: 1.6E
Type: Direct-Access ANSI SCSI revision: 00
Vendor: Generic Model: SM Rev: 1.6E
Type: Direct-Access ANSI SCSI revision: 00
usb-storage: device scan complete
sd 0:0:0:0: Attached scsi removable disk sda
sd 0:0:0:1: Attached scsi removable disk sdb
sd 0:0:0:2: Attached scsi removable disk sdc
sd 0:0:0:3: Attached scsi removable disk sdd
More information about the fedora-test-list
mailing list