[Date Prev][Date Next]   [Thread Prev][Thread Next]   [Thread Index] [Date Index] [Author Index]

Re: Kudzu segmentation fault. Core5 Test3 upto date as of March 4, 2006



I am suffering the same problem with seg faults using kudzu. My system is a Dell Inspiron 8000 (PIII 700 Mhz laptop). 'kudzu -s' does not cause a seg fault. I can file a bug if the other gentleman has not already done so and add this information along with whatever else you need.

lspci -vv lists the following hardware:
00:00.0 Host bridge: Intel Corporation 82815 815 Chipset Host Bridge and Memory Controller Hub (rev 02) Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR+ FastB2B- Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort+ >SERR- <PERR-
       Latency: 0
       Region 0: Memory at e8000000 (32-bit, prefetchable) [size=64M]
       Capabilities: [88] Vendor Specific Information
       Capabilities: [a0] AGP version 2.0
Status: RQ=32 Iso- ArqSz=0 Cal=0 SBA+ ITACoh- GART64- HTrans- 64bit- FW- AGP3- Rate=x1,x2,x4 Command: RQ=1 ArqSz=0 Cal=0 SBA- AGP- GART64- 64bit- FW- Rate=<none>

00:01.0 PCI bridge: Intel Corporation 82815 815 Chipset AGP Bridge (rev 02) (prog-if 00 [Normal decode]) Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR+ FastB2B- Status: Cap- 66MHz+ UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR-
       Latency: 32
       Bus: primary=00, secondary=01, subordinate=01, sec-latency=32
       I/O behind bridge: 0000c000-0000cfff
       Memory behind bridge: fc000000-fdffffff
       Prefetchable memory behind bridge: d8000000-e7ffffff
Secondary status: 66MHz+ FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort+ <SERR- <PERR+
       BridgeCtl: Parity- SERR- NoISA+ VGA+ MAbort- >Reset- FastB2B-

00:1e.0 PCI bridge: Intel Corporation 82801 Mobile PCI Bridge (rev 03) (prog-if 00 [Normal decode]) Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR+ FastB2B- Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR-
       Latency: 0
       Bus: primary=00, secondary=02, subordinate=10, sec-latency=32
       I/O behind bridge: 0000d000-0000ffff
       Memory behind bridge: f2000000-fbffffff
       Prefetchable memory behind bridge: 20000000-23ffffff
Secondary status: 66MHz- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort+ <SERR- <PERR-
       BridgeCtl: Parity- SERR+ NoISA+ VGA- MAbort- >Reset- FastB2B-

00:1f.0 ISA bridge: Intel Corporation 82801BAM ISA Bridge (LPC) (rev 03)
Control: I/O+ Mem+ BusMaster+ SpecCycle+ MemWINV- VGASnoop- ParErr- Stepping- SERR+ FastB2B- Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
       Latency: 0

00:1f.1 IDE interface: Intel Corporation 82801BAM IDE U100 (rev 03) (prog-if 80 [Master])
       Subsystem: Intel Corporation Unknown device 4541
Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
       Latency: 0
       Region 4: I/O ports at bfa0 [size=16]

00:1f.2 USB Controller: Intel Corporation 82801BA/BAM USB (Hub #1) (rev 03) (prog-if 00 [UHCI])
       Subsystem: Intel Corporation Unknown device 4541
Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
       Latency: 0
       Interrupt: pin D routed to IRQ 10
       Region 4: I/O ports at bce0 [size=32]

01:00.0 VGA compatible controller: nVidia Corporation NV17 [GeForce4 440 Go] (rev a3) (prog-if 00 [VGA])
       Subsystem: Dell Unknown device 00a4
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop+ ParErr- Stepping- SERR- FastB2B- Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
       Latency: 32 (1250ns min, 250ns max)
       Interrupt: pin A routed to IRQ 11
       Region 0: Memory at fc000000 (32-bit, non-prefetchable) [size=16M]
       Region 1: Memory at e0000000 (32-bit, prefetchable) [size=128M]
       Region 2: Memory at dff80000 (32-bit, prefetchable) [size=512K]
       Expansion ROM at d8000000 [disabled] [size=128K]
       Capabilities: [60] Power Management version 2
Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-)
               Status: D0 PME-Enable- DSel=0 DScale=0 PME-
       Capabilities: [44] AGP version 2.0
Status: RQ=32 Iso- ArqSz=0 Cal=0 SBA- ITACoh- GART64- HTrans- 64bit- FW+ AGP3- Rate=x1,x2,x4 Command: RQ=1 ArqSz=0 Cal=0 SBA- AGP- GART64- 64bit- FW- Rate=<none>

02:03.0 Multimedia audio controller: ESS Technology ES1983S Maestro-3i PCI Audio Accelerator (rev 10)
       Subsystem: Dell Unknown device 00a4
Control: I/O+ Mem+ BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
       Interrupt: pin A routed to IRQ 5
       Region 0: I/O ports at dc00 [size=256]
       Region 1: Memory at f6ffe000 (32-bit, non-prefetchable) [size=8K]
       Capabilities: [c0] Power Management version 2
Flags: PMEClk- DSI+ D1+ D2+ AuxCurrent=0mA PME(D0-,D1+,D2+,D3hot+,D3cold-)
               Status: D0 PME-Enable- DSel=0 DScale=0 PME+

02:06.0 PCI bridge: Actiontec Electronics Inc Mini-PCI bridge (rev 11) (prog-if 00 [Normal decode]) Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
       Latency: 32, Cache Line Size 08
       Bus: primary=02, secondary=08, subordinate=08, sec-latency=32
       I/O behind bridge: 0000e000-0000efff
       Memory behind bridge: f8000000-f9ffffff
Secondary status: 66MHz- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- <SERR- <PERR-
       BridgeCtl: Parity- SERR+ NoISA+ VGA- MAbort- >Reset- FastB2B-
       Capabilities: [80] Power Management version 2
Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=0mA PME(D0-,D1+,D2+,D3hot+,D3cold+)
               Status: D0 PME-Enable- DSel=0 DScale=0 PME-
               Bridge: PM- B3+
       Capabilities: [90] #06 [0000]

02:0f.0 CardBus bridge: Texas Instruments PCI4451 PC card Cardbus Controller
       Subsystem: Dell Unknown device 00a4
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
       Latency: 168, Cache Line Size 20
       Interrupt: pin A routed to IRQ 10
       Region 0: Memory at f6000000 (32-bit, non-prefetchable) [size=4K]
       Bus: primary=02, secondary=09, subordinate=0c, sec-latency=176
       Memory window 0: 20000000-21fff000 (prefetchable)
       Memory window 1: f2000000-f3fff000
       I/O window 0: 0000d000-0000d0ff
       I/O window 1: 0000d400-0000d4ff
BridgeCtl: Parity- SERR- ISA- VGA- MAbort- >Reset+ 16bInt+ PostWrite+
       16-bit legacy interface ports at 0001

02:0f.1 CardBus bridge: Texas Instruments PCI4451 PC card Cardbus Controller
       Subsystem: Dell Unknown device 00a4
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
       Latency: 168, Cache Line Size 20
       Interrupt: pin A routed to IRQ 10
       Region 0: Memory at f6001000 (32-bit, non-prefetchable) [size=4K]
       Bus: primary=02, secondary=0d, subordinate=10, sec-latency=176
       Memory window 0: 22000000-23fff000 (prefetchable)
       Memory window 1: f4000000-f5fff000
       I/O window 0: 0000d800-0000d8ff
       I/O window 1: 00001000-000010ff
BridgeCtl: Parity- SERR- ISA- VGA- MAbort- >Reset+ 16bInt+ PostWrite+
       16-bit legacy interface ports at 0001

02:0f.2 FireWire (IEEE 1394): Texas Instruments PCI4451 IEEE-1394 Controller (prog-if 10 [OHCI])
       Subsystem: Dell Unknown device 00a4
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV+ VGASnoop- ParErr- Stepping- SERR+ FastB2B- Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
       Latency: 32 (500ns min, 1000ns max), Cache Line Size 08
       Interrupt: pin A routed to IRQ 10
       Region 0: Memory at f6ffd800 (32-bit, non-prefetchable) [size=2K]
       Region 1: Memory at f6ff8000 (32-bit, non-prefetchable) [size=16K]
       Capabilities: [44] Power Management version 2
Flags: PMEClk- DSI- D1- D2+ AuxCurrent=0mA PME(D0-,D1-,D2+,D3hot+,D3cold-)
               Status: D0 PME-Enable- DSel=0 DScale=0 PME-

08:04.0 Ethernet controller: Intel Corporation 82557/8/9 [Ethernet Pro 100] (rev 08) Subsystem: Actiontec Electronics Inc EtherExpress PRO/100B (TX) (MiniPCI Ethernet+Modem) Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV+ VGASnoop- ParErr- Stepping- SERR+ FastB2B- Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
       Latency: 32 (2000ns min, 14000ns max), Cache Line Size 08
       Interrupt: pin A routed to IRQ 10
       Region 0: Memory at f8fff000 (32-bit, non-prefetchable) [size=4K]
       Region 1: I/O ports at ecc0 [size=64]
       Region 2: Memory at f8e00000 (32-bit, non-prefetchable) [size=1M]
       Capabilities: [dc] Power Management version 2
Flags: PMEClk- DSI+ D1+ D2+ AuxCurrent=0mA PME(D0+,D1+,D2+,D3hot+,D3cold+)
               Status: D0 PME-Enable- DSel=0 DScale=2 PME-

08:08.0 Communication controller: Agere Systems WinModem 56k (rev 01)
Subsystem: Actiontec Electronics Inc LT WinModem 56k (MiniPCI Ethernet+Modem) Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR+ FastB2B- Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
       Latency: 0 (63000ns min, 3500ns max)
       Interrupt: pin A routed to IRQ 10
       Region 0: Memory at f8ffec00 (32-bit, non-prefetchable) [size=256]
       Region 1: I/O ports at ecb8 [size=8]
       Region 2: I/O ports at e800 [size=256]
       Capabilities: [f8] Power Management version 2
Flags: PMEClk- DSI+ D1- D2+ AuxCurrent=0mA PME(D0-,D1-,D2+,D3hot+,D3cold+)
               Status: D0 PME-Enable- DSel=0 DScale=0 PME-


----- Original Message ----- From: "Jonathan Berry" <berryja gmail com> To: "For testers of Fedora Core development releases" <fedora-test-list redhat com>
Sent: Sunday, March 05, 2006 12:52 PM
Subject: Re: Kudzu segmentation fault. Core5 Test3 upto date as of March 4,2006


On 3/4/06, Leslie Satenstein <lsatenstein yahoo com> wrote:
-rwxr-xr-x 1 root root 157444 Feb 28 15:00 kudzu

And yet you refuse to give us any more information regarding your
system.  What hardware do you have?  What architecture are you
running?  Are you using Xen?  Please be helpful.  Just saying that
something isn't working is not being helpful.

Jonathan

--
fedora-test-list mailing list
fedora-test-list redhat com
To unsubscribe:
https://www.redhat.com/mailman/listinfo/fedora-test-list



[Date Prev][Date Next]   [Thread Prev][Thread Next]   [Thread Index] [Date Index] [Author Index]