VIA Eden Framebuffer troubles
Bond, Darryl
dbond at nrggos.com.au
Wed Mar 26 09:42:31 UTC 2008
Initializing cgroup subsys cpuset
Linux version 2.6.24.3-34.fc8 (mockbuild at xenbuilder2.fedora.redhat.com) (gcc version 4.1.2 20070925 (Red Hat 4.1.2-33)) #1 SMP Wed Mar 12 16:43:35 EDT 2008
BIOS-provided physical RAM map:
BIOS-e820: 0000000000000000 - 000000000009fc00 (usable)
BIOS-e820: 000000000009fc00 - 00000000000a0000 (reserved)
BIOS-e820: 00000000000f0000 - 0000000000100000 (reserved)
BIOS-e820: 0000000000100000 - 00000000077f0000 (usable)
BIOS-e820: 00000000077f0000 - 00000000077f3000 (ACPI NVS)
BIOS-e820: 00000000077f3000 - 0000000007800000 (ACPI data)
BIOS-e820: 00000000ffff0000 - 0000000100000000 (reserved)
0MB HIGHMEM available.
119MB LOWMEM available.
Using x86 segment limits to approximate NX protection
Entering add_active_range(0, 0, 30704) 0 entries of 256 used
Zone PFN ranges:
DMA 0 -> 4096
Normal 4096 -> 30704
HighMem 30704 -> 30704
Movable zone start PFN for each node
early_node_map[1] active PFN ranges
0: 0 -> 30704
On node 0 totalpages: 30704
DMA zone: 32 pages used for memmap
DMA zone: 0 pages reserved
DMA zone: 4064 pages, LIFO batch:0
Normal zone: 207 pages used for memmap
Normal zone: 26401 pages, LIFO batch:7
HighMem zone: 0 pages used for memmap
Movable zone: 0 pages used for memmap
DMI 2.2 present.
Using APIC driver default
ACPI: RSDP 000F6240, 0014 (r0 VIA601)
ACPI: RSDT 077F3000, 0028 (r1 VIA601 AWRDACPI 42302E31 AWRD 0)
ACPI: FACP 077F3040, 0074 (r1 VIA601 AWRDACPI 42302E31 AWRD 0)
ACPI: DSDT 077F30C0, 2370 (r1 VIA601 AWRDACPI 1000 MSFT 100000D)
ACPI: FACS 077F0000, 0040
ACPI: PM-Timer IO Port: 0x4008
Allocating PCI resources starting at 10000000 (gap: 07800000:f87f0000)
swsusp: Registered nosave memory region: 000000000009f000 - 00000000000a0000
swsusp: Registered nosave memory region: 00000000000a0000 - 00000000000f0000
swsusp: Registered nosave memory region: 00000000000f0000 - 0000000000100000
Built 1 zonelists in Zone order, mobility grouping on. Total pages: 30465
Kernel command line: rw initrd=initrd.ltsp quiet selinux=0 vga=normal BOOT_IMAGE=vmlinuz.ltsp auto
No local APIC present or hardware disabled
mapped APIC to ffffb000 (010fb000)
Initializing CPU#0
CPU 0 irqstacks, hard=c07ba000 soft=c079a000
PID hash table entries: 512 (order: 9, 2048 bytes)
Detected 533.377 MHz processor.
Console: colour VGA+ 80x25
console [tty0] enabled
Dentry cache hash table entries: 16384 (order: 4, 65536 bytes)
Inode-cache hash table entries: 8192 (order: 3, 32768 bytes)
Memory: 110608k/122816k available (2237k kernel code, 11660k reserved, 1131k data, 284k init, 0k highmem)
virtual kernel memory layout:
fixmap : 0xffc52000 - 0xfffff000 (3764 kB)
pkmap : 0xff800000 - 0xffc00000 (4096 kB)
vmalloc : 0xc8000000 - 0xff7fe000 ( 887 MB)
lowmem : 0xc0000000 - 0xc77f0000 ( 119 MB)
.init : 0xc0750000 - 0xc0797000 ( 284 kB)
.data : 0xc062f7ee - 0xc074a724 (1131 kB)
.text : 0xc0400000 - 0xc062f7ee (2237 kB)
Checking if this processor honours the WP bit even in supervisor mode... Ok.
SLUB: Genslabs=11, HWalign=32, Order=0-1, MinObjects=4, CPUs=1, Nodes=1
Calibrating delay using timer specific routine.. 1067.99 BogoMIPS (lpj=533995)
Security Framework initialized
SELinux: Disabled at boot.
Capability LSM initialized
Mount-cache hash table entries: 512
Initializing cgroup subsys ns
Initializing cgroup subsys cpuacct
CPU: After generic identify, caps: 00803035 80803035 00000000 00000000 00000000 00000000 00000000 00000000
CPU: L1 I Cache: 64K (32 bytes/line), D cache 64K (32 bytes/line)
CPU: L2 Cache: 64K (32 bytes/line)
CPU: After all inits, caps: 00803135 80803035 00000000 00000000 00000000 00000000 00000000 00000000
Compat vDSO mapped to ffffe000.
Checking 'hlt' instruction... OK.
SMP alternatives: switching to UP code
Freeing SMP alternatives: 14k freed
ACPI: Core revision 20070126
ACPI: setting ELCR to 0200 (from 0e20)
CPU0: Centaur VIA Samuel 2 stepping 03
SMP motherboard not detected.
Local APIC not detected. Using dummy APIC emulation.
Brought up 1 CPUs
sizeof(vma)=84 bytes
sizeof(page)=32 bytes
sizeof(inode)=336 bytes
sizeof(dentry)=132 bytes
sizeof(ext3inode)=488 bytes
sizeof(buffer_head)=56 bytes
sizeof(skbuff)=176 bytes
sizeof(task_struct)=1680 bytes
CPU0 attaching sched-domain:
domain 0: span 00000001
groups: 00000001
net_namespace: 64 bytes
Booting paravirtualized kernel on bare hardware
Time: 4:57:42 Date: 03/25/04
NET: Registered protocol family 16
No dock devices found.
ACPI: bus type pci registered
PCI: PCI BIOS revision 2.10 entry at 0xfb180, last bus=1
PCI: Using configuration type 1
Setting up standard PCI resources
ACPI: EC: Look up EC in DSDT
ACPI: Interpreter enabled
ACPI: (supports S0 S1 S4 S5)
ACPI: Using PIC for interrupt routing
ACPI: PCI Root Bridge [PCI0] (0000:00)
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0._PRT]
ACPI: PCI Interrupt Link [LNKA] (IRQs 1 3 4 5 6 7 10 *11 12 14 15)
ACPI: PCI Interrupt Link [LNKB] (IRQs 1 3 4 5 6 7 10 11 12 14 15) *0, disabled.
ACPI: PCI Interrupt Link [LNKC] (IRQs 1 3 4 5 6 7 *10 11 12 14 15)
ACPI: PCI Interrupt Link [LNKD] (IRQs 1 3 4 *5 6 7 10 11 12 14 15)
Linux Plug and Play Support v0.97 (c) Adam Belay
pnp: PnP ACPI init
ACPI: bus type pnp registered
pnp: PnP ACPI: found 13 devices
ACPI: ACPI bus type pnp unregistered
usbcore: registered new interface driver usbfs
usbcore: registered new interface driver hub
usbcore: registered new device driver usb
PCI: Using ACPI for IRQ routing
PCI: If a device doesn't work, try "pci=routeirq". If it helps, post a report
NetLabel: Initializing
NetLabel: domain hash size = 128
NetLabel: protocols = UNLABELED CIPSOv4
NetLabel: unlabeled traffic allowed by default
Time: tsc clocksource has been installed.
system 00:00: iomem range 0xd6000-0xd7fff has been reserved
system 00:00: iomem range 0xf0000-0xf7fff could not be reserved
system 00:00: iomem range 0xf8000-0xfbfff could not be reserved
system 00:00: iomem range 0xfc000-0xfffff could not be reserved
system 00:00: iomem range 0x77f0000-0x77fffff could not be reserved
system 00:00: iomem range 0xffff0000-0xffffffff could not be reserved
system 00:00: iomem range 0x0-0x9ffff could not be reserved
system 00:00: iomem range 0x100000-0x77effff could not be reserved
system 00:00: iomem range 0xfee00000-0xfee00fff has been reserved
system 00:02: ioport range 0x4d0-0x4d1 has been reserved
PCI: Bridge: 0000:00:01.0
IO window: disabled.
MEM window: e8000000-eaffffff
PREFETCH window: 10000000-100fffff
PCI: Setting latency timer of device 0000:00:01.0 to 64
NET: Registered protocol family 2
IP route cache hash table entries: 1024 (order: 0, 4096 bytes)
TCP established hash table entries: 4096 (order: 3, 32768 bytes)
TCP bind hash table entries: 4096 (order: 3, 32768 bytes)
TCP: Hash tables configured (established 4096 bind 4096)
TCP reno registered
checking if image is initramfs...<7>Switched to high resolution mode on CPU 0
it is
Freeing initrd memory: 5939k freed
apm: BIOS version 1.2 Flags 0x07 (Driver version 1.16ac)
apm: overridden by ACPI.
audit: initializing netlink socket (disabled)
audit(1080190666.045:1): initialized
Total HugeTLB memory allocated, 0
VFS: Disk quotas dquot_6.5.1
Dquot-cache hash table entries: 1024 (order 0, 4096 bytes)
ksign: Installing public key data
Loading keyring
- Added public key A0F6F514211EF299
- key was been created 125163676 seconds in future
- User ID: Red Hat, Inc. (Kernel Module GPG key)
Block layer SCSI generic (bsg) driver version 0.4 loaded (major 253)
io scheduler noop registered
io scheduler anticipatory registered
io scheduler deadline registered
io scheduler cfq registered (default)
PCI: VIA PCI bridge detected. Disabling DAC.
Boot video device is 0000:01:00.0
pci_hotplug: PCI Hot Plug PCI Core version: 0.5
ACPI: Fan [FAN] (on)
ACPI: CPU0 (power states: C1[C1] C2[C2])
ACPI: Processor [CPU0] (supports 2 throttling states)
ACPI: Thermal Zone [THRM] (32 C)
isapnp: Scanning for PnP cards...
isapnp: No Plug & Play device found
Real Time Clock Driver v1.12ac
Non-volatile memory driver v1.2
Linux agpgart interface v0.102
agpgart: Detected VIA Apollo ProMedia/PLE133Ta chipset
agpgart: AGP aperture is 128M @ 0xe0000000
Serial: 8250/16550 driver $Revision: 1.90 $ 4 ports, IRQ sharing enabled
serial8250: ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A
00:08: ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A
RAMDISK driver initialized: 16 RAM disks of 16384K size 4096 blocksize
input: Macintosh mouse button emulation as /devices/virtual/input/input0
PNP: PS/2 Controller [PNP0303:PS2K,PNP0f13:PS2M] at 0x60,0x64 irq 1,12
serio: i8042 KBD port at 0x60,0x64 irq 1
serio: i8042 AUX port at 0x60,0x64 irq 12
mice: PS/2 mouse device common for all mice
input: AT Translated Set 2 keyboard as /devices/platform/i8042/serio0/input/input1
cpuidle: using governor ladder
input: PS/2 Logitech Mouse as /devices/platform/i8042/serio1/input/input2
cpuidle: using governor menu
usbcore: registered new interface driver hiddev
usbcore: registered new interface driver usbhid
drivers/hid/usbhid/hid-core.c: v2.6:USB HID core driver
TCP cubic registered
Initializing XFRM netlink socket
NET: Registered protocol family 1
NET: Registered protocol family 17
Using IPI No-Shortcut mode
registered taskstats version 1
Magic number: 12:722:970
Freeing unused kernel memory: 284k freed
Write protecting the kernel read-only data: 893k
ohci_hcd: 2006 August 04 USB 1.1 'Open' Host Controller (OHCI) Driver
USB Universal Host Controller Interface driver v3.0
ACPI: PCI Interrupt Link [LNKD] enabled at IRQ 5
PCI: setting IRQ 5 as level-triggered
ACPI: PCI Interrupt 0000:00:11.2[D] -> Link [LNKD] -> GSI 5 (level, low) -> IRQ 5
uhci_hcd 0000:00:11.2: UHCI Host Controller
uhci_hcd 0000:00:11.2: new USB bus registered, assigned bus number 1
uhci_hcd 0000:00:11.2: irq 5, io base 0x0000d400
usb usb1: configuration #1 chosen from 1 choice
hub 1-0:1.0: USB hub found
hub 1-0:1.0: 2 ports detected
ACPI: PCI Interrupt 0000:00:11.3[D] -> Link [LNKD] -> GSI 5 (level, low) -> IRQ 5
uhci_hcd 0000:00:11.3: UHCI Host Controller
uhci_hcd 0000:00:11.3: new USB bus registered, assigned bus number 2
uhci_hcd 0000:00:11.3: irq 5, io base 0x0000d800
usb usb2: configuration #1 chosen from 1 choice
hub 2-0:1.0: USB hub found
hub 2-0:1.0: 2 ports detected
RPC: Registered udp transport module.
RPC: Registered tcp transport module.
NET: Registered protocol family 23
via-ircc: dongle probing not supported, please specify dongle_id module parameter.
IrDA: Registered device irda0 (via-ircc)
via-rhine.c:v1.10-LK1.4.3 2007-03-06 Written by Donald Becker
via-rhine: Broken BIOS detected, avoid_D3 enabled.
ACPI: PCI Interrupt Link [LNKA] enabled at IRQ 11
PCI: setting IRQ 11 as level-triggered
ACPI: PCI Interrupt 0000:00:12.0[A] -> Link [LNKA] -> GSI 11 (level, low) -> IRQ 11
eth0: VIA Rhine II at 0xeb000000, 00:40:63:d3:14:32, IRQ 11.
eth0: MII PHY found at address 1, status 0x786d advertising 05e1 Link 45e1.
eth0: link up, 100Mbps, full-duplex, lpa 0x45E1
SCSI subsystem initialized
input: PC Speaker as /devices/platform/pcspkr/input/input3
Floppy drive(s): fd0 is 1.44M
FDC 0 is a post-1991 82077
libata version 3.00 loaded.
input: Power Button (FF) as /devices/virtual/input/input4
ACPI: Power Button (FF) [PWRF]
input: Power Button (CM) as /devices/virtual/input/input5
ACPI: Power Button (CM) [PWRB]
pata_via 0000:00:11.1: version 0.3.3
scsi0 : pata_via
scsi1 : pata_via
ata1: PATA max UDMA/100 cmd 0x1f0 ctl 0x3f6 bmdma 0xd000 irq 14
ata2: PATA max UDMA/100 cmd 0x170 ctl 0x376 bmdma 0xd008 irq 15
ata2: port disabled. ignoring.
cyblafb: CyblaFB version 0.62 initializing
ACPI: PCI Interrupt 0000:01:00.0[A] -> Link [LNKA] -> GSI 11 (level, low) -> IRQ 11
fbcon: CyBla (fb0) is primary device
Console: switching to colour frame buffer device 80x25
parport_pc: VIA 686A/8231 detected
parport_pc: probing current configuration
parport_pc: Current parallel port base: 0x378
parport0: PC-style at 0x378, irq 7 [PCSPP,EPP]
parport_pc: VIA parallel port: io=0x378, irq=7
ACPI: PCI Interrupt Link [LNKC] enabled at IRQ 10
PCI: setting IRQ 10 as level-triggered
ACPI: PCI Interrupt 0000:00:11.5[C] -> Link [LNKC] -> GSI 10 (level, low) -> IRQ 10
PCI: Setting latency timer of device 0000:00:11.5 to 64
device-mapper: uevent: version 1.0.3
device-mapper: ioctl: 4.12.0-ioctl (2007-10-02) initialised: dm-devel at redhat.com
NET: Registered protocol family 10
lo: Disabled Privacy Extensions
cdpinger[1244]: segfault at 6f72647f eip 00159d52 esp bfbe8e70 error 4
eth0: no IPv6 routers present
________________________________________
From: k12linux-devel-list-bounces at redhat.com [k12linux-devel-list-bounces at redhat.com] On Behalf Of Warren Togami [wtogami at redhat.com]
Sent: Wednesday, March 26, 2008 1:33 AM
To: Development discussion of K12Linux
Subject: Re: VIA Eden Framebuffer troubles
Could you also send the output of dmesg?
Warren
_______________________________________________
K12Linux-devel-list mailing list
K12Linux-devel-list at redhat.com
https://www.redhat.com/mailman/listinfo/k12linux-devel-list
The contents of this electronic message and any attachments are intended only for the addressee and may contain legally privileged, personal, sensitive or confidential information. If you are not the intended addressee, and have received this email, any transmission, distribution, downloading, printing or photocopying of the contents of this message or attachments is strictly prohibited. Any legal privilege or confidentiality attached to this message and attachments is not waived, lost or destroyed by reason of delivery to any person other than intended addressee. If you have received this message and are not the intended addressee you should notify the sender by return email and destroy all copies of the message and any attachments. Unless expressly attributed, the views expressed in this email do not necessarily represent the views of the company.
More information about the K12Linux-devel-list
mailing list