.config

[Williams, Mitch]

Warren
I have some console out and log file as follows: Looks like it it grabbing regular elf instead of wraplinux?

-mlw

console out:
============

CPU 433 MHz

Memory 400 MHz
done cpuRegInit
DIMM0 256MB @ CL 3,0
DRAM controller init done.
DRAM size needs to be reconfigured
DIMM0 128MB @ CL 3,0
DRAM controller init done.
DRAM 128MB configuration OK

LinuxBIOS for ThinCan
(C) Artec Group 2006, 2007
http://www.thincan.com

LinuxBIOS-1.1.8.0-dbe61-1.3 R juuli 27 15:05:18 EEST 2007 booting...
Enumerating buses...
Installing VSA2... done
Finding PCI configuration type.
done
Allocating resources...
Reading resources...
Done reading resources.
Setting resources...
Done setting resources.
Done allocating resources.
Enabling resources...
done.
Initializing devices...
Initializing CPU #0
Enabling cache
CPU #0 Initialized
Installing VGA BIOS... done
Devices initialized

Welcome to elfboot, the open sourced starter.
January 2002, Eric Biederman.
Version 1.3

Loading Etherboot version: 5.4.2-dbe61

LinuxBIOS loaded.
(C) Artec Group 2006, 2007
http://www.thincan.com



CPU 445 Mhz
Etherboot 5.4.2-dbe61 (GPL) http://etherboot.org
Drivers: RTL8139   Images: NBI ELF FreeBSD Multiboot a.out
Protocols: DHCP TFTP NFS
Relocating _text from: [000101b0,0002bc60) to [070e4550,07100000)
Probing pci nic...
[rtl8139] - ioaddr 0X1000, irq 10, addr 00:18:2D:00:0B:12 100Mbps full-duplex
Searching for server (DHCP)...\
Me: 172.31.100.100, DHCP: 172.31.100.254, TFTP: 172.31.100.254, Gateway 172.31.4
Loading 172.31.100.254:/ltsp/i386/elf.ltsp (ELF)... done
Firmware type: LinuxBIOS
relocating ramdisk to 0x06c3e000
�

/var/log/messages:
==================

Feb 18 10:48:10 localhost kernel: eth1: link up, 100Mbps, full-duplex, lpa 0x41E
1
Feb 18 10:48:10 localhost kernel: ADDRCONF(NETDEV_CHANGE): eth1: link becomes re
ady
Feb 18 10:48:10 localhost kernel: ltspbr0: port 1(eth1) entering learning state
Feb 18 10:48:10 localhost netplugd[2052]: eth1: state INACTIVE flags 0x00001103
UP,BROADCAST,PROMISC,MULTICAST -> 0x00011143 UP,BROADCAST,RUNNING,PROMISC,MULTIC
AST,10000
Feb 18 10:48:10 localhost netplugd[6131]: /etc/netplug.d/netplug eth1 in -> pid
6131
Feb 18 10:48:10 localhost kernel: ltspbr0: topology change detected, propagating
Feb 18 10:48:10 localhost kernel: ltspbr0: port 1(eth1) entering forwarding stat
e
Feb 18 10:48:14 localhost dhcpd: DHCPDISCOVER from 00:18:2d:00:0b:12 via ltspbr0
Feb 18 10:48:15 localhost dhcpd: DHCPOFFER on 172.31.100.100 to 00:18:2d:00:0b:1
2 via ltspbr0
Feb 18 10:48:15 localhost dhcpd: DHCPREQUEST for 172.31.100.100 (172.31.100.254)
 from 00:18:2d:00:0b:12 via ltspbr0
Feb 18 10:48:15 localhost dhcpd: DHCPACK on 172.31.100.100 to 00:18:2d:00:0b:12
via ltspbr0
Feb 18 10:48:15 localhost netplugd[2052]: eth1: state INNING pid 6131 exited sta
tus 0



________________________________________
From: k12linux-devel-list-bounces at redhat.com [k12linux-devel-list-bounces at redhat.com] On Behalf Of Warren Togami [wtogami at redhat.com]
Sent: Wednesday, February 18, 2009 8:26 AM
To: Development discussion of K12Linux
Subject: Re: .config

Williams, Mitch wrote:
> Hello,
>
> we are attempting to get(artec dbe61)  LX800 hardware to work with
> coreboot/FC10/ k12linux/ltsp. Can you point us in the direction of
> the client kernel config file?
>
> -mlw

/boot/config-* contains the kernel config file, but this has nothing to
do with netbooting it.

I have an Artec DBE61 with coreboot.  It boots just fine with the
mkelfimage wrapped NBI image automatically created by K12Linux's
installation procedure.  ltsp-dhcpd's /etc/ltsp/dhcpd.conf automatically
gives the client wraplinux-nbi.ltsp if its DHCP vendor-class-identifier
was "Etherboot-5.4".

Warren Togami
wtogami at redhat.com

_______________________________________________
K12Linux-devel-list mailing list
K12Linux-devel-list at redhat.com
https://www.redhat.com/mailman/listinfo/k12linux-devel-list