[libvirt] [PATCH] qemu: call drive_unplug in DetachPciDiskDevice

[Ryan Harper]

* Daniel P. Berrange <berrange at redhat.com> [2010-10-21 12:10]:
> On Thu, Oct 21, 2010 at 11:53:29AM -0500, Ryan Harper wrote:
> > * Daniel P. Berrange <berrange at redhat.com> [2010-10-21 11:46]:
> > > On Thu, Oct 21, 2010 at 08:50:35AM -0500, Ryan Harper wrote:
> > > > Currently libvirt doesn't confirm whether the guest has responded to the
> > > > disk removal request.  In some cases this can leave the guest with
> > > > continued access to the device while the mgmt layer believes that it has
> > > > been removed.  With a recent qemu monitor command[1] we can
> > > > deterministically revoke a guests access to the disk (on the QEMU side)
> > > > to ensure no futher access is permitted.
> > > > 
> > > > This patch adds support for the drive_unplug() command and introduces it
> > > > in the disk removal paths.  There is some discussion to be had about how
> > > > to handle the case where the guest is running in a QEMU without this
> > > > command (and the fact that we currently don't have a way of detecting
> > > > what monitor commands are available).
> > > 
> > > Basically we try to run the command and then catch the failure.
> > > 
> > > For QMP, we can check for a error with a class of 'CommandNotFound',
> > > 
> > > For HMP, QEMU will print 'unknown command' in the reply.
> > > 
> > > Neither is ideal, since neither is a guarenteed part of the monitor
> > > interface, but it is all we have to go on, and ensure other critical
> > > errors will still be treated as fatal by libvirt.
> > 
> > Yeah, this sorta already works without explictly catching the error
> > (unless you want to display a different message at caller level than
> > command not found).
> 
> This would cause the hot-unplug operation to completely terminate
> though, whereas we want it to carry on, if the command is not
> present. If we get a command-not-found, then we should syslog a 
> warning, and then return '0' (ie success) to the caller of
> qemuMonitorDriveUnplug
> 
> Alternatively, return '+1' to the caller, and make the callers
> check for '+1', syslog it and treat it as non-fatal. This is
> closer to the approach we use for handling 'balloon device not
> present' error when code runs the 'info balloon' method.
> 
> > > > My current implementation assumes that if you don't have a QEMU with
> > > > this capability that we should fail the device removal.  This is a
> > > > strong statement around hotplug that isn't consistent with previous
> > > > releases so I'm open to other approachs, but given the potential data
> > > > leakage problem hot-remove can lead to without drive_unplug, I think
> > > > it's the right thing to do.
> > > 
> > > I don't think we can do this, since it obviously breaks every single
> > > existing deployment out there. Users who have sVirt enabled will
> > > have a level of protection from the data leakage, so I don't think
> > > it is a severe problem. 
> > 
> > Yeah, I was thinking we could re-work the logic to only completely fail
> > in the case where the command wasn't found/successful *and* we don't
> > have sVirt enabled.
> 
> I'm still wary of doing that because of the significant negative
> impact on existing deployments out there, even in the case where
> hotunplug would complete just fine. I think we'll just need to
> syslog the potential issue and people can upgrade their QMEU if
> they need the extra security

OK, I'll respin.

> 
> Regards,
> Daniel
> -- 
> |: Red Hat, Engineering, London    -o-   http://people.redhat.com/berrange/ :|
> |: http://libvirt.org -o- http://virt-manager.org -o- http://deltacloud.org :|
> |: http://autobuild.org        -o-         http://search.cpan.org/~danberr/ :|
> |: GnuPG: 7D3B9505  -o-   F3C9 553F A1DA 4AC2 5648 23C1 B3DF F742 7D3B 9505 :|

-- 
Ryan Harper
Software Engineer; Linux Technology Center
IBM Corp., Austin, Tx
ryanh at us.ibm.com