[Date Prev][Date Next]   [Thread Prev][Thread Next]   [Thread Index] [Date Index] [Author Index]

Re: [libvirt] nwfilter - limit VM traffic to specific mac address



On 11/10/2011 05:21 AM, Shahar Havivi wrote:
On 10.11.11 11:30, Shahar Havivi wrote:
On 09.11.11 10:49, Stefan Berger wrote:
On 11/09/2011 09:38 AM, Shahar Havivi wrote:
On 09.11.11 09:20, Stefan Berger wrote:
On 11/09/2011 07:44 AM, Shahar Havivi wrote:
On 09.11.11 06:44, Stefan Berger wrote:
On 11/09/2011 04:01 AM, Shahar Havivi wrote:
On 08.11.11 16:34, Stefan Berger wrote:
On 11/07/2011 04:25 AM, Shahar Havivi wrote:
Hi,

I want to limit VM traffic to a specific MAC address, ie VMs cannot
traffic each other other then a specific gateway.

I am using custom nwfilter name: isolatedprivatevlan-vdsm.xml
located in /etc/libvirt/nwfilter/:

<filter name='isolatedprivatevlan-vdsm' chain='root'>
     <filterref filter='clean-traffic'/>
     <rule action='drop' direction='out' priority='500'>
         <mac match='no' dstmacaddr='$GATEWAY_MAC'/>
     </rule>
</filter>

Try this one -- it works in 'my' subnet:

<filter name='isolatedprivatevlan-vdsm' chain='ipv4'>
     <filterref filter='clean-traffic'/>
     <rule action='drop' direction='out' priority='10'>
         <mac match='no' dstmacaddr='$GATEWAY_MAC'/>
     </rule>
</filter>
Thanks,
Now it is blocking the traffic but I can't get traffic to the gateway as
well...
That's odd. Can you ping the gateway from the VM? Is it typically
ping-able? Are you sure you specified the correct MAC addresses --
check with 'arp -n' on a host in the same subnet and see what it
shows for the gateway (ping it if you don't see an entry).

     Stefan
It's working only when I remove the line
     <filterref filter='clean-traffic'/>
>from the filter...
While you ping the gateway, can you re-add the above line to the filter?

    Stefan
its working, even when stopping the ping and re-pinging the gateway,
but it stop working after I stop and started the VM.

How does the VM get its IP address, static or DHCP ? If DHCP, could
you try a static IP address?

In case it doesn't work, what does 'ebtables -t nat -L' show and
which IP address is assigned to the VM's interface?

    Stefan
static ip, the ebtables output show ip 0.0.0.0 for the VM mac address:

Bridge chain: I-vnet0-rarp, entries: 2, policy: ACCEPT
-p 0x8035 -s 0:1a:4a:16:1:52 -d Broadcast --arp-op Request_Reverse
--arp-ip-src 0.0.0.0 --arp-ip-dst 0.0.0.0 --arp-mac-src 0:1a:4a:16:1:52
--arp-mac-dst 0:1a:4a:16:1:52 -j ACCEPT
-j DROP

Bridge chain: O-vnet0-rarp, entries: 2, policy: ACCEPT
-p 0x8035 -d Broadcast --arp-op Request_Reverse --arp-ip-src 0.0.0.0
--arp-ip-dst 0.0.0.0 --arp-mac-src 0:1a:4a:16:1:52 --arp-mac-dst
0:1a:4a:16:1:52 -j ACCEPT
-j DROP


How can I set the IP in the case?
Ok,
its working when I set the IP in the filter:
<filterref filter='clean-traffic'>
     <parameter name='IP' value='10.35.16.50'/>
</filterref>

I guess its the only solution...?
The IP address in the parameter XML node has to match the one assigned to the interface inside the VM. If they don't match nothing works. If you leave out the line '<parameter name=.../>' then this will start libvirt's IP address learning/detection that will lock your VM into the first IP address it detects that the VM is using on a particular interface. This should also work.

   Stefan
--
libvir-list mailing list
libvir-list redhat com
https://www.redhat.com/mailman/listinfo/libvir-list


[Date Prev][Date Next]   [Thread Prev][Thread Next]   [Thread Index] [Date Index] [Author Index]