[Date Prev][Date Next]   [Thread Prev][Thread Next]   [Thread Index] [Date Index] [Author Index]

[libvirt] [PATCH 2/4] docs: boot order for host and redirected USB devices



And a few spaces.
---
 docs/formatdomain.html.in |   27 +++++++++++++++++++--------
 1 files changed, 19 insertions(+), 8 deletions(-)

diff --git a/docs/formatdomain.html.in b/docs/formatdomain.html.in
index c8da33d..6a3b976 100644
--- a/docs/formatdomain.html.in
+++ b/docs/formatdomain.html.in
@@ -2192,7 +2192,8 @@
       boot sequence. The per-device <code>boot</code> elements cannot be
       used together with general boot elements in
       <a href="#elementsOSBIOS">BIOS bootloader</a> section.
-      <span class="since">Since 0.8.8</span></dd>
+      <span class="since">Since 0.8.8</span> for PCI devices,
+      <span class="since">Since 1.0.1</span> for USB devices.
       <dt><code>rom</code></dt>
       <dd>The <code>rom</code> element is used to change how a PCI
         device's ROM is presented to the guest. The optional <code>bar</code>
@@ -2237,6 +2238,7 @@
   &lt;devices&gt;
     &lt;redirdev bus='usb' type='tcp'&gt;
       &lt;source mode='connect' host='localhost' service='4000'/&gt;
+      &lt;boot order='1'/&gt;
     &lt;/redirdev&gt;
     &lt;redirfilter&gt;
       &lt;usbdev class='0x08' vendor='0x1234' product='0xbeef' version='2.00' allow='yes'/&gt;
@@ -2258,24 +2260,33 @@
         tunnel; <code>type='tcp'</code>
         or <code>type='spicevmc'</code> (which uses the usbredir
         channel of a <a href="#elementsGraphics">SPICE graphics
-        device</a>) are typical.The redirdev element has an optional
-        sub-element<code>&lt;address&gt;</code> which can tie the
+        device</a>) are typical. The redirdev element has an optional
+        sub-element <code>&lt;address&gt;</code> which can tie the
         device to a particular controller. Further sub-elements,
         such as <code>&lt;source&gt;</code>, may be required according
         to the given type, although a <code>&lt;target&gt;</code> sub-element
         is not required (since the consumer of the character device is
-        the hypervisor itself,rather than a device visible in the guest).
+        the hypervisor itself, rather than a device visible in the guest).
+      </dd>
+      <dt><code>boot</code></dt>
+
+      <dd>Specifies that the device is bootable.
+        The <code>order</code> attribute determines the order in which
+        devices will be tried during boot sequence. The per-device
+        <code>boot</code> elements cannot be used together with general
+        boot elements in  <a href="#elementsOSBIOS">BIOS bootloader</a> section.
+        (<span class="since">Since 1.0.1</span>)
       </dd>
       <dt><code>redirfilter</code></dt>
       <dd>The<code> redirfilter </code>element is used for creating the
         filter rule to filter out certain devices from redirection.
-        It uses sub-element <code>&lt;usbdev&gt;</code>to define each filter rule.
-        <code>class</code>attribute is the USB Class code, for example,
+        It uses sub-element <code>&lt;usbdev&gt;</code> to define each filter rule.
+        <code>class</code> attribute is the USB Class code, for example,
         0x08 represents mass storage devices. The USB device can be addressed by
-        vendor / product id using the<code>vendor</code> and <code>product</code> attributes.
+        vendor / product id using the <code>vendor</code> and <code>product</code> attributes.
         <code>version</code> is the bcdDevice value of USB device, such as 1.00, 1.10 and 2.00.
         These four attributes are optional and <code>-1</code> can be used to allow
-        any value for them. <code>allow</code>attribute is mandatory,
+        any value for them. <code>allow</code> attribute is mandatory,
         'yes' means allow, 'no' for deny.
       </dd>
     </dl>
-- 
1.7.8.6


[Date Prev][Date Next]   [Thread Prev][Thread Next]   [Thread Index] [Date Index] [Author Index]