[Date Prev][Date Next]   [Thread Prev][Thread Next]   [Thread Index] [Date Index] [Author Index]

Re: [Linux-cluster] Fence don't work with HP iLo2 (fw.1.42



I don't get it working:
This error message comes..when i try to fence node2.

Jan 12 20:38:57 xxx4n1 fence_node[20776]: agent "fence_ipmilan" reports: Rebooting machine @ IPMI:192.168.69.4...ipmilan: Failed to connect after 30 seconds Failed
Jan 12 20:38:57 xxx4n1 ccsd[3239]: Attempt to close an unopened CCS descriptor (142830).
Jan 12 20:38:57 xxx4n1 ccsd[3239]: Error while processing disconnect: Invalid request descriptor

Some ideas?

tameikareed kirjoitti 12.01.2008 kello 18:24:
> Hi,
> 
> Do you have IPMI turned on in your kernel.  It should be if you didn't 
> recompile your kernel, but it not you can install that module.  As far 
> as recompiling your kernel, RedHat does not support that so you will 
> have to download the vanilla kernel from kernel.org.  This will be the 
> source kernel.  Once you have that I would open up a second screen and 
> do a make menuconfig on the kernel that you do have installed under 
> /usr/src/kernels/<kernel-version>. In the other screen install the 
> source kernel with rpm -ivh <kernel src version>. Then build the kernel 
> by going over to /usr/src/redhat/SPECS and doing rpmbuild -bp 
> kernel<version>.spec.  Below is a list of options:
> 
>         -ba    Build binary and source packages (after doing the %prep, 
> %build, and %install stages).
> 
>        -bb    Build a binary package (after doing the %prep, %build,
>  and 
> %install stages).
> 
>        -bp    Executes the "%prep" stage from the spec file. Normally 
> this involves unpacking the sources and applying any patches.
> 
>        -bc    Do  the "%build" stage from the spec file (after doing
>  the 
> %prep stage).  This generally involves the equivalent of a "make".
> 
>        -bi    Do the "%install" stage from the spec file (after doing 
> the %prep and %build stages).  This generally involves the equivalent
>               of a "make install".
> 
>        -bl    Do  a  "list check".  The "%files" section from the spec 
> file is macro expanded, and checks are made to verify that each file
>               exists.
> After that you need to make a symbolic link over in the
>  /usr/src/kernel/ 
> directory linking back to your source directory of the 
> kernel.(/usr/src/kernels/BUILD)
> 
> As far as with HP hardware, you can look on the disk. Or check this
>  link 
> out:
> http://h20000.www2.hp.com/bizsupport/TechSupport/SoftwareDescription.jsp?lan
> g=en&cc=us&mode=3&taskId=135&swItem=MTX-UNITY-I25296
> 
> I would go with the HP drivers . This should have came in hpasm
>  package. 
> I have include the instructions from the hp site:
> 
> *Installation:*
> Login as the system administrator (root), download the RPM to a 
> directory on your hard drive and change to that directory.
> 
> If a previous version of the hp-OpenIPMI package has been installed, it 
> must be removed before this package can be installed. To remove the 
> previous version and any packages dependent on it, type the following:
> 
>       rpm -e hp-OpenIPMI
> 
> To install the package, type:
> 
>       rpm -ivh hp-OpenIPMI-< version >.rpm
> 
> The drivers will be installed to the /opt/hp/hp-OpenIPMI directory but 
> not inserted. For HP ProLiant servers, the hpasm package will 
> automatically load the hp-OpenIPMI drivers if required for a particular 
> HP ProLiant server.
> 
> Additional information and help is available by typing either of the 
> following:
> 
>       man hp-OpenIPMI
> 
> Additional information about features, installation, use, and 
> troubleshooting the HP Server Management Drivers and Agents is
>  available 
> in the HOWTO documents available here: 
> http://www.compaq.com/products/servers/linux/documentation.html.
> 
> Well hope this helps,
> Tameika
> 
> m.. mm.. wrote:
> > Hello again.
> > Hmm, i don't know how to enable ipmi in Hp360 iLo2, can somebody help me
> and explain it to me?
> >
> > And how is the config-parameters in cluster-suite at fence device.
> >
> > Sorry, i don't understand it, and didnä't get it work..
> > .ipmilan: Failed to connect after 30 seconds Failed
> >
> >
> > Lon Hohberger kirjoitti 12.01.2008 kello 00:19:
> >   
> >> On Fri, 2008-01-11 at 22:56 +0200, m.. mm.. wrote:
> >>     
> >>> Hi
> >>> We are having some problems to get fence working with this hardware.
> >>>
> >>> Proliant 360 G5.. iLo firmware 1.42
> >>> and os is, RedHat 5-> 2.6.18-8.el5 Cluster/GFS
> >>>
> >>> This script: fence_ilo
> >>> Fence shutdown works fine, but it don't restart it.
> >>> agent "fence_ilo" reports: failed to turn on
> >>>
> >>> Have someone working script to get this work?
> >>>       
> >> Enable IPMI on the iLO2 management card and use it instead.
> >>
> >> -- Lon
> >>
> >>
> >> --
> >> Linux-cluster mailing list
> >> Linux-cluster redhat com
> >> https://www.redhat.com/mailman/listinfo/linux-cluster
> >>     
> >
> >
> > ...................................................................
> > Luukku Plus paketilla pääset eroon tila- ja turvallisuusongelmista.
> > Hanki Luukku Plus ja helpotat elämääsi. http://www.mtv3.fi/luukku
> >
> >
> > --
> > Linux-cluster mailing list
> > Linux-cluster redhat com
> > https://www.redhat.com/mailman/listinfo/linux-cluster
> >
> >   
> 


...................................................................
Luukku Plus paketilla pääset eroon tila- ja turvallisuusongelmista.
Hanki Luukku Plus ja helpotat elämääsi. http://www.mtv3.fi/luukku



[Date Prev][Date Next]   [Thread Prev][Thread Next]   [Thread Index] [Date Index] [Author Index]