[Date Prev][Date Next]   [Thread Prev][Thread Next]   [Thread Index] [Date Index] [Author Index]

Re: [Linux-cluster] really reliable?



I'm running RHEL 5.3 64-bit.  So far, I only want to see that the
cluster can run.  I'll worry about getting GFS after I'm confident this
works.

I've got three nodes: pico, vail, and whistler.  They each have two NIC
cards, one that provides a public IP address, and another that provides
private communications.  All cluster traffic will go over the private
network, 192.168.20.0.

I've installed only the following components:
system-config-cluster-1.0.52-1.1, cman-2.0.98-1, and rgmanager-2.0.38-2.

I've created my cluster.conf file to include these three nodees and
fence them using a brocade fibre switch (for GFS).

When I start the cluster services on all 3 nodes using the manually method of:

/sbin/ccsd; /usr/sbin/cman_tool join

The nodes successfully form a cluster. I am able to leave the cluster and kill ccsd as well.

If I try to start the cman service I see:

[root pico cluster]# /sbin/service cman start
Starting cluster:
   Loading modules... done
   Mounting configfs... done
   Starting ccsd... done
   Starting cman... done
   Starting daemons... done
   Starting fencing...


And it just hangs. I know my fencing is set up correctly because I've had nodes fence other nodes before (when I was trying with 6 members). If I let it sit for long enough sometimes it finishes successfully. I'm not sure what its doing because fence_tool is called and its a binary...

Ryan


Gordan Bobic wrote:
What distro are you using? I've found that:

1) Distros other than RHEL/CentOS can be quirky when it comes to using
RHCS. I've even run into problems on Fedora more than once (not to mention
that FC hasn't shipped GFS1 since FC5 and GFS2 hasn't been deemed
production stable until last month - and we're up to FC10 now).

2) Starting RHCS components using anything except the intended init scripts
tends to cause problems.

3) Source of 99% of problems in the rest of the cases (i.e. not covered by
1) and 2) above) is incorrectly configured fencing.

Does your setup fall under either of the first two categories?
Have you verified beyond doubt that your fencing is configured correctly
and that the fencing script gets verification upon success?

Gordan

On Tue, 14 Apr 2009 12:17:44 -0400, Ryan Golhar <golharam umdnj edu> wrote:
Hi all,

Is redhat cluster suite really reliable? I've been having so much trouble getting a cluster up and running, I'm beginning to second guess my decision to use this software stack.

I have 3 nodes (eventually 10) running and set up. The fencing method is by a brocade fibre switch. The ultimate goal of this cluster is to shared a SAN connected by fibre.

I've installed just the bare minimum (before even getting to GFS) to test the cluster software. Just starting cman cluster services fails on two of the nodes.

Even when I try to reboot the nodes, I can't because the whole system hangs on various processes that don't ever shut down. I have to physically reboot these boxes.

The logs fill up with errors about not being able to connect to cman,
etc.
I've been at it for awhile now and am not sure this is the best route anymore.

Ryan

--
Linux-cluster mailing list
Linux-cluster redhat com
https://www.redhat.com/mailman/listinfo/linux-cluster


begin:vcard
fn:Ryan Golhar, Ph.D.
n:Golhar;Ryan
org:University of Medicine & Dentistry of New Jersey;CIC/Bioinformatics, The Cancer Institute of NJ
adr:Room 5564-04;;195 Little Albany St;New Brunswick;NJ;08901-1914;USA
email;internet:golharam umdnj edu
title:System Architect, caBIG Deployment Lead
tel;work:(732) 235-6613
tel;fax:(732) 235-6267
tel;cell:(732) 236-1176
x-mozilla-html:FALSE
url:http://www.cinj.org
version:2.1
end:vcard


[Date Prev][Date Next]   [Thread Prev][Thread Next]   [Thread Index] [Date Index] [Author Index]