[Linux-cluster] do I have a fence DRAC device?

[ESGLinux]

2009/8/11 Juan Ramon Martin Blanco <robejrm at gmail.com>

>
>
> On Tue, Aug 11, 2009 at 2:03 PM, ESGLinux <esggrupos at gmail.com> wrote:
>
>> Thanks
>> I´ll check it when I could reboot the server.
>>
>> greetings,
>>
> You have a BMC ipmi in the first network interface, it can be configured at
> boot time (I don't  remember if inside the BIOS or pressing cntrl+something
> during boot)
>


Hi,

I have finally rebooted my system and entered inside the BIOS with CTRL+E
command.
I have configured the card and now when I run the command ipmitool lan print
I get this information:

ipmitool lan print
Set in Progress         : Set Complete
Auth Type Support       : NONE MD2 MD5 PASSWORD
Auth Type Enable        : Callback : MD2 MD5
                        : User     : MD2 MD5
                        : Operator : MD2 MD5
                        : Admin    : MD2 MD5
                        : OEM      : MD2 MD5
IP Address Source       : Static Address
IP Address              : 192.168.1.250
Subnet Mask             : 255.255.255.0
MAC Address             : 00:1e:c9:ae:6f:7e
SNMP Community String   : public
IP Header               : TTL=0x40 Flags=0x40 Precedence=0x00 TOS=0x10
Default Gateway IP      : 192.168.1.1
Default Gateway MAC     : 00:00:00:00:00:00
Backup Gateway IP       : 0.0.0.0
Backup Gateway MAC      : 00:00:00:00:00:00
802.1q VLAN ID          : Disabled
802.1q VLAN Priority    : 0
RMCP+ Cipher Suites     : 0,1,2,3,4,5,6,7,8,9,10,11,12,13,14
Cipher Suite Priv Max   : aaaaaaaaaaaaaaa
                        :     X=Cipher Suite Unused
                        :     c=CALLBACK
                        :     u=USER
                        :     o=OPERATOR
                        :     a=ADMIN
                        :     O=OEM


If I make ping 192.168.1.250 I get response but I can´t do anymore. If I run
the racadm commands I still get the errors:

ERROR: RACADM is unable to process the requested subcommand because there is
no
local RAC configuration to communicate with.

Local RACADM subcommand execution requires the following:

 1. A Remote Access Controller (RAC) must be present on the managed server
 2. Appropriate managed node software must be installed and running on the
    server


I have tried to access that ip, but I can´t do nothing with it. I have done
a port scan and I nothing is listening there,

What else do I have to do to get this working?

Thanks,

ESG






>
> Greetings,
> Juanra
>
>>
>> ESG
>>
>> 2009/8/10 Paras pradhan <pradhanparas at gmail.com>
>>
>> On Mon, Aug 10, 2009 at 5:24 AM, ESGLinux<esggrupos at gmail.com> wrote:
>>> > Hi all,
>>> > I was designing a 2 node cluster and I was going to use 2 servers DELL
>>> > PowerEdge 1950. I was going to buy a DRAC card to use for fencing but
>>> > running several commands in the servers I have noticed that when I run
>>> this
>>> > command:
>>> > #ipmitool lan print
>>> > Set in Progress : Set Complete
>>> > Auth Type Support : NONE MD2 MD5 PASSWORD
>>> > Auth Type Enable : Callback : MD2 MD5
>>> >                         : User : MD2 MD5
>>> >                         : Operator : MD2 MD5
>>> >                         : Admin : MD2 MD5
>>> >                         : OEM : MD2 MD5
>>> > IP Address Source : Static Address
>>> > IP Address : 0.0.0.0
>>> > Subnet Mask : 0.0.0.0
>>> > MAC Address : 00:1e:c9:ae:6f:7e
>>> > SNMP Community String : public
>>> > IP Header : TTL=0x40 Flags=0x40 Precedence=0x00 TOS=0x10
>>> > Default Gateway IP : 0.0.0.0
>>> > Default Gateway MAC : 00:00:00:00:00:00
>>> > Backup Gateway IP : 0.0.0.0
>>> > Backup Gateway MAC : 00:00:00:00:00:00
>>> > 802.1q VLAN ID : Disabled
>>> > 802.1q VLAN Priority : 0
>>> > RMCP+ Cipher Suites : 0,1,2,3,4,5,6,7,8,9,10,11,12,13,14
>>> > Cipher Suite Priv Max : aaaaaaaaaaaaaaa
>>> >                         : X=Cipher Suite Unused
>>> >                         : c=CALLBACK
>>> >                         : u=USER
>>> >                         : o=OPERATOR
>>> >                         : a=ADMIN
>>> >                         : O=OEM
>>> > does this mean that I already have an ipmi card (not configured) that I
>>> can
>>> > use for fencing? if the anwser is yes, where hell must I configure it?
>>> I
>>> > don´t see wher can I do it.
>>> > If I haven´t a fencing device which one do you recommed to use?
>>> > Thanks in advance
>>> > ESG
>>> >
>>> > --
>>> > Linux-cluster mailing list
>>> > Linux-cluster at redhat.com
>>> > https://www.redhat.com/mailman/listinfo/linux-cluster
>>> >
>>>
>>> Yes you have IPMI and if you are using 1950 Dell, DRAC should be there
>>> too. You can see if you have DRAC or not when the server starts and
>>> before the loading of the OS.
>>>
>>> I have 1850s and I am using DRAC for fencing.
>>>
>>>
>>> Paras.
>>>
>>> --
>>> Linux-cluster mailing list
>>> Linux-cluster at redhat.com
>>> https://www.redhat.com/mailman/listinfo/linux-cluster
>>>
>>
>>
>> --
>> Linux-cluster mailing list
>> Linux-cluster at redhat.com
>> https://www.redhat.com/mailman/listinfo/linux-cluster
>>
>
>
> --
> Linux-cluster mailing list
> Linux-cluster at redhat.com
> https://www.redhat.com/mailman/listinfo/linux-cluster
>
-------------- next part --------------
An HTML attachment was scrubbed...
URL: <http://listman.redhat.com/archives/linux-cluster/attachments/20090817/9f5dfa6f/attachment.htm>