[linux-lvm] Kernel PANIC after partition change on RedHat 8.0
Yuliy Minchev
yuliy at mobiltel.bg
Sun Jan 19 02:36:01 UTC 2003
On Sun, 19 Jan 2003, Yuliy Minchev wrote:
I have to update the case.
I've tried to move /dev/sdb3 to the end of the hard drive.
After this, I recreated sdb45 on the same size free space, but starting at
lower cyl (again after 1024).
And it works. Systems does not hang. I can run pvcreate, vgextend and so
on...
After this I deleted again disk partition sdb45
and move /dev/sdb3 on its inital place.
I recreated again sdb45 and again system hangs.
This whole lot looks to strange to me :(
It should be like this. As long as I know - position on hard disk is not
important at all.
> On Sun, 19 Jan 2003, Steven Lembark wrote:
>
> >
> >
> > -- Yuliy Minchev <yuliy at mobiltel.bg>
> >
> > > On Sat, 18 Jan 2003, Steven Lembark wrote:
> > >
> > >>
> > >> > I have installed Red Hat Linux 8.0. I've made volume group (rootvg)
> > >> > from /dev/md1 (which is raid1). I've put my /boot on /dev/md0.
> > >> >
> > >> > As you already have noticed - I have two disks.
> > >> > After installation I'm making new partiotion /dev/sdb5 i.e.
> > >> > And if I change its to type to 8e after reboot kernel panics.
> > >> > If I change type of this partition to something different - the system
> > >> > boots fine.
> > >> >
> > >> > I cannot understand where can be the problem.
> > >> > I have to say that I made the same configuration on this machine and
> > >> > everything was ok. But now I cannot see any difference.
> > >>
> > >> sdb5 => sub-partition. Are you accidentally carving out
> > >> a piece of an existing PV? For example, if you had partitioned
> > >> the disk into /dev/sdb[1234] when it was built with sdb4 taking
> > >> up most of the device as 8e (i.e., for LVM), then adding sdb5
> > >> w/in the area of sdb4 would certianly break things -- and scramble
> > >> your LV's during pvcreate on the new partition.
> > >
> > > I have
> > >
> > > /dev/sdb1 /boot (member of md0,raid1)
> > > /dev/sdb1 member of md1, raid1, on md1 is my volume group
> > > /dev/sdb3 fat32
> > > /dev/sbd4 extend partion
> > > /dev/sdb5 is defined as 8e within sdb4
> > >
> > > Sorry, but I did not understand your point :(
> >
> > One thing people have zapped themselves with in the past
> > is something like:
> >
> > /dev/sdb4 == one partition
> > /dev/sdb5 == another partition whose space is
> > contained w/in /dev/sdb4
> >
> > pvcreate -ff /dev/sdb4;
> > vgcreate vg00 /dev/sdb4;
> > lvcretate ... vg00;
> >
> > <later in time>
> >
> > pvcreate -ff /dev/sdb5;
> > vgcreate vg01 /dev/sdb5;
> > lvcreate ... vg01;
> >
> > at this point the creation of vg01 has overwritten
> > data in vg00 becuase the partition /dev/sda5 uses
> > disk realestate contained within /dev/sda4. This is
> > a matter purely caused by having moultiple partitions
> > w/in the same spindle.
> >
> > That is why I wondered if you had made the mistake
> > of creating a partition w/in an already-existing
> > partition which was used as a PV at the time when
> > your new partition was created and used.
>
> No, no...
> The case is not like this. There is no such overlapping here.
>
> I created my volume group during RH8 installation.
> After that I manually created /dev/sdb4 and within /dev/sbd5 with fdisk.
> And when I change the type of /dev/sbd5 to 8e in order to be able
> to run pvcreate ot it and to add it to my volume groups - the
> systems hangs during kernel loading. In fact, the system stops to
> recognise my volume group. That's why it hangs.
>
> yuliy
>
>
> >
> >
> >
> > --
> > Steven Lembark 2930 W. Palmer
> > Workhorse Computing Chicago, IL 60647
> > +1 773 252 1080
> >
> > _______________________________________________
> > linux-lvm mailing list
> > linux-lvm at sistina.com
> > http://lists.sistina.com/mailman/listinfo/linux-lvm
> > read the LVM HOW-TO at http://tldp.org/HOWTO/LVM-HOWTO/
> >
>
>
--
Yuliy Minchev,
UNIX Administrator
More information about the linux-lvm
mailing list