[Ovirt-devel] ovirt node GSS Failure
Joey Boggs
jboggs at redhat.com
Tue Sep 15 14:39:03 UTC 2009
Joey Boggs wrote:
> Pretty standard broadcom card. on the node run lsmod and see if tg3 or
> bnx2 show up, also see if breth0 or eth0 show up in ifconfig. Are you
> sure the node is pxebooting and not booting off the local disk?
>
>
>
> ignazio.cassano at provincia.torino.it wrote:
>> Ethernet card on my node is Broadcom NetXtreme II BCM5709 Gigabith
>> ethernet
>>
>>
>>
>> ----- Messaggio da jboggs at redhat.com ---------
>> Data: Tue, 15 Sep 2009 09:50:31 -0400
>> Da: Joey Boggs <jboggs at redhat.com>
>> Rispondi-A:Joey Boggs <jboggs at redhat.com>
>> Oggetto: Re: [Ovirt-devel] ovirt node GSS Failure
>> A: ignazio.cassano at provincia.torino.it
>> Cc: ovirt-devel at redhat.com
>>
>>
>>> ignazio.cassano at provincia.torino.it wrote:
>>>> Alan, now node finishes the boot e "root login:" appears.
>>>> The problem is it does not respond if I ping it.
>>>> How can I login on it ?
>>>> Which is the root password ?
>>>> I'd like to check network configuration
>>>>
>>>> ----- Messaggio da ignazio.cassano at provincia.torino.it ---------
>>>> Data: Tue, 15 Sep 2009 15:06:19 +0200
>>>> Da: ignazio.cassano at provincia.torino.it
>>>> Rispondi-A:ignazio.cassano at provincia.torino.it
>>>> Oggetto: Re: [Ovirt-devel] ovirt node GSS Failure
>>>> A: Alan Pevec <apevec at gmail.com>
>>>> Cc: ovirt-devel at redhat.com
>>>>
>>>>
>>>>> Hello, I am going to install livecd tools but I have a question
>>>>> first:
>>>>>
>>>>> must management net and public net comunicate isung a router ?
>>>>> In my configuration mgmt net and pub net are isolated.
>>>>>
>>>>>
>>>>>
>>>>> ----- Messaggio da apevec at gmail.com ---------
>>>>> Data: Tue, 15 Sep 2009 14:37:14 +0200
>>>>> Da: Alan Pevec <apevec at gmail.com>
>>>>> Rispondi-A:Alan Pevec <apevec at gmail.com>
>>>>> Oggetto: Re: [Ovirt-devel] ovirt node GSS Failure
>>>>> A: ignazio.cassano at provincia.torino.it
>>>>> Cc: ovirt-devel at redhat.com
>>>>>
>>>>>
>>>>>> On Tue, Sep 15, 2009 at 11:27 AM,
>>>>>> <ignazio.cassano at provincia.torino.it>wrote:
>>>>>>
>>>>>>> I tried to start a phisical node and it start to load the pxe
>>>>>>> image but
>>>>>>> then
>>>>>>> it seems frozen.
>>>>>>>
>>>>>>
>>>>>> Could you capture serial console log? At what point it freezes?
>>>>>> Please check if you have livecd-tools-024-1ovirt.fc11.x86_64 (from
>>>>>> ovirt.orgrepo) installed on the machine where
>>>>>> ovirt-node-image-pxe RPM
>>>>>> is installed.
>>>>>> If not, install it first and then reinstall -pxe (it runs
>>>>>> livecd-iso-to-pxeboot in post script)
>>>>>>
>>>>>
>>>>>
>>>>> ----- Fine del messaggio da apevec at gmail.com -----
>>>>>
>>>>>
>>>>>
>>>>>
>>>>> _______________________________________________
>>>>> Ovirt-devel mailing list
>>>>> Ovirt-devel at redhat.com
>>>>> https://www.redhat.com/mailman/listinfo/ovirt-devel
>>>>
>>>>
>>>> ----- Fine del messaggio da ignazio.cassano at provincia.torino.it -----
>>>>
>>>>
>>>>
>>>>
>>>> _______________________________________________
>>>> Ovirt-devel mailing list
>>>> Ovirt-devel at redhat.com
>>>> https://www.redhat.com/mailman/listinfo/ovirt-devel
>>>
>>> In /var/log/messages you can check for the dhcp request/ack which will
>>> have the mac/ip address assigned to the node. You can then ssh from the
>>> management server to it. Does the root login prompt have an associated
>>> hostname? nodeXX login: ?
>>
>>
>> ----- Fine del messaggio da jboggs at redhat.com -----
>>
>>
>>
>
> _______________________________________________
> Ovirt-devel mailing list
> Ovirt-devel at redhat.com
> https://www.redhat.com/mailman/listinfo/ovirt-devel
Looks like that card might not have the updated module mapping based on
a quick search:
Run lspci -nn on the node and grab the output for the broadcom card:
Here's an example for an intel nic:
02:00.0 Ethernet controller [0200]: Intel Corporation 82573L Gigabit
Ethernet Controller [8086:109a]
More information about the ovirt-devel
mailing list