[Pki-users] (Fedora 17) PKI-RA fails to start after install

Andrew Wnuk awnuk at redhat.com
Wed Jun 5 17:20:00 UTC 2013


On 06/04/2013 02:57 PM, Andrew Wnuk wrote:
> On 06/03/2013 07:10 AM, Ade Lee wrote:
>> Can you attach the logs under /var/log/pki-tps ?
>> Also, check /var/log/messages to see if there are any messages there.
>>
>> Another thing you can try is to set selinux in permissive mode, and see
>> if the server starts.
>>
>> Ade
> You could also try to disable syntax checking in your directory server.
https://access.redhat.com/site/documentation/en-US/Red_Hat_Directory_Server/8.2/html/Administration_Guide/syntax-validation.html#syntax-validation-basic
>>
>> On Fri, 2013-05-31 at 17:46 -0400, Brian Henson wrote:
>>> This is the only error i see in the TPS install log [2013-05-29
>>> 03:37:20] [error] FAILED run_command("/bin/systemctl restart
>>> pki-tpsd at pki-tps.service"), exit status=1 output="Job failed. See
>>> system journal and 'systemctl status' for details." and the same
>>> error(minus service name on the other service)
>>>
>>>
>>> On Fri, May 31, 2013 at 5:14 PM, Andrew Wnuk <awnuk at redhat.com> wrote:
>>>          On 05/31/2013 07:53 AM, Brian Henson wrote:
>>>                   > I don't mean to sound dumb but where is the 
>>> logfiles? I am
>>>          > using the wiki install page as a guide.
>>>                            Installation logs are under /var/log with 
>>> names referring to
>>>          subsystems like: pki-ca-install.log, pki-kra-install.log,
>>>          pki-tks-install.log, pki-tks-install.log, . . .
>>>                   Each subsystem has its logs located under 
>>> subsystem directory.
>>>          For example
>>>                *  CA logs by default are located in /var/log/pki-ca
>>>                *  TPS logs by default are located in /var/log/pki-tps
>>>                *  . . .
>>>                   >
>>>          >
>>>          > On Thu, May 30, 2013 at 4:01 PM, Andrew Wnuk
>>>          > <awnuk at redhat.com> wrote:
>>>          >
>>>          >         Is there anything in the log files pointing to your
>>>          >         failure?
>>>          >         If yes, could you provide these log entries?
>>>          >
>>>          >         On 05/30/2013 11:34 AM, Brian Henson wrote:
>>>          >
>>>          >         > Any Ideas on this? I need the TPS for the
>>>          >         > smartcard support.
>>>          >         >
>>>          >         >
>>>          >         > On Wed, May 29, 2013 at 1:24 PM, Brian Henson
>>>          >         > <marine64 at gmail.com> wrote:
>>>          >         >         Fedora 17 and dogtag 9 via yum
>>>          >         >
>>>          >         >         On May 29, 2013 12:01 PM, "Andrew Wnuk"
>>>          >         >         <awnuk at redhat.com> wrote:
>>>          >         >
>>>          >         >                 On 05/28/2013 09:46 PM, Brian
>>>          >         >                 Henson wrote:
>>>          >         >
>>>          >         >                 > Hello all,
>>>          >         >                 >
>>>          >         >                 >
>>>          >         >                 > When I try to configure the RA
>>>          >         >                 > subsystem after installing it I
>>>          >         >                 > get this error.
>>>          >         >                 >
>>>          >         >                 >
>>>          >         >                 > Installation information
>>>          >         >                 > recorded
>>>          >         >                 > in /var/log/pki-ra-install.log.
>>>          >         >                 > [debug]
>>>          >         >                 > run_command(/bin/systemctl
>>>          >         >                 > restart pki-rad at pki-ra.service)
>>>          >         >                 > [error] FAILED
>>>          >         >                 > run_command("/bin/systemctl
>>>          >         >                 > restart
>>>          >         >                 > pki-rad at pki-ra.service"), exit
>>>          >         >                 > status=1 output="Job failed. See
>>>          >         >                 > system journal and 'systemctl
>>>          >         >                 > status' for details."
>>>          >         >                 > Before proceeding with the
>>>          >         >                 > configuration, make sure
>>>          >         >                 > the firewall settings of this
>>>          >         >                 > machine permit proper
>>>          >         >                 > access to this subsystem.
>>>          >         >                 >
>>>          >         >                 >
>>>          >         >                 > Please start the configuration
>>>          >         >                 > by accessing:
>>>          >         >                 >
>>>          >         >                 >
>>>          >         >                 > 
>>> https://(someaddress):12890/ra/admin/console/config/login?pin=XWdsV1oDtx9qQFcybzAr
>>>          >         >                 >
>>>          >         >                 >
>>>          >         >                 > After configuration, the server
>>>          >         >                 > can be operated by the command:
>>>          >         >                 >
>>>          >         >                 >
>>>          >         >                 > /bin/systemctl restart
>>>          >         >                 > pki-rad at pki-ra.service
>>>          >         >                 >
>>>          >         >                 >
>>>          >         >                 >
>>>          >         >                 >
>>>          >         >                 > Anyone know how to fix this? I
>>>          >         >                 > get it for the TPS module as
>>>          >         >                 > well.
>>>          >         >                 >
>>>          >         >                 >
>>>          >         >                 > Thanks
>>>          >         >                 >
>>>          >         >                 >
>>>          >         >                 > Brian Henson
>>>          >         >                 >
>>>          >         >                 >
>>>          >         >
>>>          >         >                 Brian,
>>>          >         >
>>>          >         >                 Could you provide OS and server
>>>          >         >                 versions?
>>>          >         >
>>>          >         >                 Thank you,
>>>          >         >                 Andrew
>>>          >         >
>>>          >         >
>>>          >         >
>>>          >
>>>          >
>>>          >
>>>          >
>>>
>>>
>>> _______________________________________________
>>> Pki-users mailing list
>>> Pki-users at redhat.com
>>> https://www.redhat.com/mailman/listinfo/pki-users
>>
>
> _______________________________________________
> Pki-users mailing list
> Pki-users at redhat.com
> https://www.redhat.com/mailman/listinfo/pki-users




More information about the Pki-users mailing list