Problem with installation of Qlogic 2310F FC card!!!

[Govind C]

----- Original Message -----
From: "Rigler, Stephen C." <srigler at marathonoil.com>
Date: Thursday, February 24, 2005 4:22 am
Subject: Re: Problem with installation of Qlogic 2310F FC card!!!

> On Wed, 2005-02-23 at 23:49 -0800, Govind C wrote:
> > 
> > Why is not recognizing the FC channel?Am very sure its a 
> Qla2310f FC 
> > card.
> > 
> > Cheers
> > 
> 
> Assuming you really do have a Ql23xx card, it should show up in the
> output of "lspci -v":
> 
> 06:01.0 Fibre Channel: QLogic Corp. QLA2312 Fibre Channel Adapter 
(rev
> 02)
>        Subsystem: QLogic Corp.: Unknown device 0100
>        Flags: bus master, 66Mhz, medium devsel, latency 64, IRQ 11
>        I/O ports at 4000 [size=256]
>        Memory at f7ff0000 (64-bit, non-prefetchable) [size=4K]
>        Expansion ROM at <unassigned> [disabled] [size=128K]
>        Capabilities: <available only to root>
> 
> 06:02.0 Fibre Channel: QLogic Corp. QLA2312 Fibre Channel Adapter 
(rev
> 02)
>        Subsystem: QLogic Corp.: Unknown device 0100
>        Flags: bus master, 66Mhz, medium devsel, latency 64, IRQ 7
>        I/O ports at 4400 [size=256]
>        Memory at f7fe0000 (64-bit, non-prefetchable) [size=4K]
>        Expansion ROM at <unassigned> [disabled] [size=128K]
>        Capabilities: <available only to root>
> 
> Not to mention the messages you'd see after powering on the machine.
> 
> -Steve
> 
> -- 
> redhat-list mailing list
> unsubscribe mailto:redhat-list-request at redhat.com?subject=unsubscribe
> https://www.redhat.com/mailman/listinfo/redhat-list
>

Still no luck

#more/etc/modules.conf
alias eth0 tg3
alias eth1 tg3
alias scsi_hostadapter mptbase
alias scsi_hostadapter1 mptscsih
alias usb-controller usb-ohci
post-remove qla2300 rmmod qla2300_conf
alias scsi_hostadapter2 qla2300
alias scsi_hostadapter3 qla2300_conf
alias scsi_hostadapter4 qla2300
alias scsi_hostadapter5 qla2300_conf
alias scsi_hostadapter5 sg
options qla2300 ql2xmaxqdepth=16 qlport_down_retry=16 
qlogin_retry_count=16 ql2xfailover=1

#lspci -v
29:01.0 Fibre Channel: QLogic Corp.: Unknown device 0300 (rev 01)
        Subsystem: QLogic Corp.: Unknown device 0106
        Flags: bus master, 66Mhz, medium devsel, latency 64, IRQ 40
        I/O ports at 3000 [size=256]
        Memory at e8001000 (64-bit, non-prefetchable) [size=4K]
        Expansion ROM at <unassigned> [disabled] [size=128K]
        Capabilities: [44] Power Management version 2
        Capabilities: [4c] PCI-X non-bridge device.
        Capabilities: [54] Message Signalled Interrupts: 64bit+ 
Queue=0/3 Enable

#modprobe qla2300
/lib/modules/2.4.21-4.ELsmp/kernel/drivers/addon/qla2200/qla2300.o: 
init_module: No such device
Hint: insmod errors can be caused by incorrect module parameters, 
including invalid IO or IRQ parameters.
      You may find more information in syslog or the output from dmesg
/lib/modules/2.4.21-4.ELsmp/kernel/drivers/addon/qla2200/qla2300.o: 
insmod /lib/modules/2.4.21-
4.ELsmp/kernel/drivers/addon/qla2200/qla2300.o failed
/lib/modules/2.4.21-4.ELsmp/kernel/drivers/addon/qla2200/qla2300.o: 
insmod qla2300 failed