[Date Prev][Date Next]   [Thread Prev][Thread Next]   [Thread Index] [Date Index] [Author Index]

RE: [rhelv5-list] Tale of 2 nic cards



eth0 and eth1 both have ONBOOT=yes

I am not fluent in reading dmesg, but it smells OK to me with the following
snips:
Bill Watson - bill magicdigits com

e1000: eth0: e1000_probe: Intel(R) PRO/1000 Network Connection
GSI 22 sharing vector 0x72 and IRQ 22
ACPI: PCI Interrupt 0000:05:00.1[B] -> GSI 19 (level, low) -> IRQ 114
PCI: Setting latency timer of device 0000:05:00.1 to 64
e1000: 0000:05:00.1: e1000_probe: (PCI Express:2.5Gb/s:32-bit)
00:15:17:30:2b:39
sd 0:0:0:0: Attached scsi generic sg0 type 0
e1000: eth1: e1000_probe: Intel(R) PRO/1000 Network Connection
sd 0:0:0:1: Attached scsi generic sg1 type 0
scsi 1:0:0:0: Attached scsi generic sg2 type 1
shpchp: Standard Hot Plug PCI Controller Driver version: 0.4
<snip>
NET: Registered protocol family 10
lo: Disabled Privacy Extensions
IPv6 over IPv4 tunneling driver

-----Original Message-----
From: rhelv5-list-bounces redhat com [mailto:rhelv5-list-bounces redhat com]
On Behalf Of Alasdair Gow
Sent: Tuesday, December 04, 2007 8:22 AM
To: Red Hat Enterprise Linux 5 (Tikanga) discussion mailing-list
Subject: Re: [rhelv5-list] Tale of 2 nic cards


Have a look in /etc/sysconfig/network-scripts/
ifcfg-eth0
ifcfg-eth1 etc....

onboot will either equal yes or no.
make sure both are yes........

if it still doesn't work have a look in dmesg for anything interesting.

Alasdair

Bill Watson wrote:
> I have an intel S5000Psl motherboard with 2 nic cards. Using the GUI 
> console, I set one to be IP4 and not IP6 fully configured with 
> gateway, dns, hostname, etc. I set the other on my LAN (tried with and 
> without a gateway
> defined) no dns, etc. I also tried the 2nd as fully configured (not IP6)
as
> I could. On both nic cards, I select start on boot. The symptoms remain
> consistent.
>
> While the system is up, I can activate both lans and they both work 
> beautifully. When I reboot, only one activates, the other says 
> inactive. I can hand activate and life is again good.
>
> The net icon in the upper right corner will only allow one network to 
> be selected at a time. I'm not sure what's up with that, or why an 
> network chooser icon is thought to be so needed as to be default 
> placed on the desktop. (my ignorance showing)
>
> Is there a clean way to have both networks launch on bootup?
>
> Thanks in advance!
> Bill Watson
> bill magicdigits com
>
>
> _______________________________________________
> rhelv5-list mailing list
> rhelv5-list redhat com 
> https://www.redhat.com/mailman/listinfo/rhelv5-list
>   


-- 
Alasdair Gow
Lumison
t: 0845 1199 900
d: 0131 514 4042

PS. Do you know that we have opened a new datacentre in Croydon? Click
https://www.lumison.net/services/pdfs/colo_croydon.pdf or give us a call
0845 119 2030 if you want to know more.


-- 

This email and any files transmitted with it are confidential and intended 
solely for the use of the individual or entity to whom they are addressed.  
If you have received this email in error please notify the sender. Any 
offers or quotation of service are subject to formal specification.  
Errors and omissions excepted.  Please note that any views or opinions 
presented in this email are solely those of the author and do not 
necessarily represent those of Lumison, nplusone or lightershade ltd.  
Finally, the recipient should check this email and any attachments for the 
presence of viruses.  Lumison, nplusone and lightershade ltd accepts no 
liability for any damage caused by any virus transmitted by this email.

_______________________________________________
rhelv5-list mailing list
rhelv5-list redhat com https://www.redhat.com/mailman/listinfo/rhelv5-list



[Date Prev][Date Next]   [Thread Prev][Thread Next]   [Thread Index] [Date Index] [Author Index]