[Date Prev][Date Next]   [Thread Prev][Thread Next]   [Thread Index] [Date Index] [Author Index]

RE: [rhelv5-list] Tale of 2 nic cards



I'm looking for further things I can do to troubleshoot my network issue.
Basically I have 2 NIC's on my motherboard - one for LAN one for WAN. When I
reboot my server, the WAN (eth0) comes up, but the LAN does not. In the
ifconfig info, the inet address for the LAN does not show. I type ifup eth1
and all is OK. ONBOOT=yes is set for both. The one that doesn't come up also
has an entry for NETWORK and BROADCAST. Since everything was set from the
GUI network config or the install DVD, I'm not sure why eth0 doesn't have
these values. Currently eth1 does not have a gateway set, but earlier tests
that also lit one lan at a time did have it set - no difference. All I can
think of listing is shown below my sig.

Thank you!
Bill Watson
bill magicdigits com

[root nedrhealy /]# ifconfig
eth0      Link encap:Ethernet  HWaddr 00:15:17:30:2B:38
          inet addr:63.138.47.3  Bcast:63.138.47.7  Mask:255.255.255.248
          inet6 addr: fe80::215:17ff:fe30:2b38/64 Scope:Link
          UP BROADCAST RUNNING MULTICAST  MTU:1500  Metric:1
          RX packets:717 errors:0 dropped:0 overruns:0 frame:0
          TX packets:767 errors:0 dropped:0 overruns:0 carrier:0
          collisions:0 txqueuelen:10
          RX bytes:75285 (73.5 KiB)  TX bytes:93824 (91.6 KiB)
          Base address:0x3020 Memory:fa820000-fa840000

eth1      Link encap:Ethernet  HWaddr 00:15:17:30:2B:39
          UP BROADCAST RUNNING MULTICAST  MTU:1500  Metric:1
          RX packets:539 errors:0 dropped:0 overruns:0 frame:0
          TX packets:57 errors:0 dropped:0 overruns:0 carrier:0
          collisions:0 txqueuelen:1000
          RX bytes:64110 (62.6 KiB)  TX bytes:9308 (9.0 KiB)
          Base address:0x3000 Memory:fa800000-fa820000

lo        Link encap:Local Loopback
          inet addr:127.0.0.1  Mask:255.0.0.0
          inet6 addr: ::1/128 Scope:Host
          UP LOOPBACK RUNNING  MTU:16436  Metric:1
          RX packets:1843 errors:0 dropped:0 overruns:0 frame:0
          TX packets:1843 errors:0 dropped:0 overruns:0 carrier:0
          collisions:0 txqueuelen:0
          RX bytes:4136600 (3.9 MiB)  TX bytes:4136600 (3.9 MiB)
[root nedrhealy /]# ifup eth1
[root nedrhealy /]# ifconfig
eth0      Link encap:Ethernet  HWaddr 00:15:17:30:2B:38
          inet addr:63.138.47.3  Bcast:63.138.47.7  Mask:255.255.255.248
          inet6 addr: fe80::215:17ff:fe30:2b38/64 Scope:Link
          UP BROADCAST RUNNING MULTICAST  MTU:1500  Metric:1
          RX packets:836 errors:0 dropped:0 overruns:0 frame:0
          TX packets:843 errors:0 dropped:0 overruns:0 carrier:0
          collisions:0 txqueuelen:10
          RX bytes:84435 (82.4 KiB)  TX bytes:101490 (99.1 KiB)
          Base address:0x3020 Memory:fa820000-fa840000

eth1      Link encap:Ethernet  HWaddr 00:15:17:30:2B:39
          inet addr:192.168.50.50  Bcast:192.168.50.255  Mask:255.255.255.0
          UP BROADCAST RUNNING MULTICAST  MTU:1500  Metric:1
          RX packets:541 errors:0 dropped:0 overruns:0 frame:0
          TX packets:68 errors:0 dropped:0 overruns:0 carrier:0
          collisions:0 txqueuelen:1000
          RX bytes:64238 (62.7 KiB)  TX bytes:11540 (11.2 KiB)
          Base address:0x3000 Memory:fa800000-fa820000

lo        Link encap:Local Loopback
          inet addr:127.0.0.1  Mask:255.0.0.0
          inet6 addr: ::1/128 Scope:Host
          UP LOOPBACK RUNNING  MTU:16436  Metric:1
          RX packets:1843 errors:0 dropped:0 overruns:0 frame:0
          TX packets:1843 errors:0 dropped:0 overruns:0 carrier:0
          collisions:0 txqueuelen:0
          RX bytes:4136600 (3.9 MiB)  TX bytes:4136600 (3.9 MiB)

[root nedrhealy /]# cd /etc/sysconfig/network-scripts
[root nedrhealy network-scripts]# ls -sal ifc*
8 -rw-r--r-- 3 root root 272 Dec 12 20:37 ifcfg-eth0
8 -rw-r--r-- 3 root root 270 Dec 12 20:37 ifcfg-eth1
4 -rw-r--r-- 1 root root 254 Jun 20  2001 ifcfg-lo
[root nedrhealy network-scripts]# cat ifcfg-eth0
# Intel Corporation 80003ES2LAN Gigabit Ethernet Controller (Copper)
DEVICE=eth0
BOOTPROTO=none
HWADDR=00:15:17:30:2B:38
ONBOOT=yes
DHCP_HOSTNAME=nedrhealy.com
TYPE=Ethernet
IPADDR=63.138.47.3
NETMASK=255.255.255.248
GATEWAY=63.138.47.1
USERCTL=no
IPV6INIT=no
PEERDNS=yes
[root nedrhealy network-scripts]# cat ifcfg-eth1
# Intel Corporation 80003ES2LAN Gigabit Ethernet Controller (Copper)
DEVICE=eth1
BOOTPROTO=none
BROADCAST=192.168.50.255
HWADDR=00:15:17:30:2B:39
IPADDR=192.168.50.50
NETMASK=255.255.255.0
NETWORK=192.168.50.0
ONBOOT=yes
TYPE=Ethernet
USERCTL=no
IPV6INIT=no
PEERDNS=yes
[root nedrhealy network-scripts]# cat ifcfg-lo
DEVICE=lo
IPADDR=127.0.0.1
NETMASK=255.0.0.0
NETWORK=127.0.0.0
# If you're having problems with gated making 127.0.0.0/8 a martian,
# you can change this to something else (255.255.255.255, for example)
BROADCAST=127.255.255.255
ONBOOT=yes
NAME=loopback
[root nedrhealy network-scripts]# cd /var/log
[root nedrhealy log]# cat dmesg
Linux version 2.6.18-53.1.4.el5 (brewbuilder hs20-bc2-3 build redhat com)
(gcc v
ersion 4.1.2 20070626 (Red Hat 4.1.2-14)) #1 SMP Wed Nov 14 10:37:27 EST
2007
Command line: ro root=/dev/VolGroup00/LogVol00 rhgb quiet
BIOS-provided physical RAM map:
 BIOS-e820: 0000000000000000 - 000000000009f400 (usable)
 BIOS-e820: 000000000009f400 - 0000000000100000 (reserved)
 BIOS-e820: 0000000000100000 - 00000000de2bd000 (usable)
 BIOS-e820: 00000000de2bd000 - 00000000de37c000 (ACPI NVS)
 BIOS-e820: 00000000de37c000 - 00000000dfa42000 (usable)
 BIOS-e820: 00000000dfa42000 - 00000000dfa9a000 (reserved)
 BIOS-e820: 00000000dfa9a000 - 00000000dfaad000 (usable)
 BIOS-e820: 00000000dfaad000 - 00000000dfb1a000 (ACPI NVS)
 BIOS-e820: 00000000dfb1a000 - 00000000dfb2b000 (usable)
 BIOS-e820: 00000000dfb2b000 - 00000000dfb3a000 (ACPI data)
 BIOS-e820: 00000000dfb3a000 - 00000000dfc00000 (usable)
 BIOS-e820: 00000000dfc00000 - 00000000f0000000 (reserved)
 BIOS-e820: 00000000ffc00000 - 00000000ffc0c000 (reserved)
 BIOS-e820: 0000000100000000 - 0000000120000000 (usable)
DMI 2.5 present.
ACPI: RSDP (v002 INTEL                                 ) @
0x00000000000f03c0
ACPI: XSDT (v001 INTEL  S5000PSL 0x00000000 INTL 0x01000013) @
0x00000000dfb3912
0
ACPI: FADT (v003 INTEL  S5000PSL 0x00000000 INTL 0x01000013) @
0x00000000dfb3700
0
ACPI: MADT (v001 INTEL  S5000PSL 0x00000000 INTL 0x01000013) @
0x00000000dfb3600
0
ACPI: SPCR (v001 INTEL  S5000PSL 0x00000000 INTL 0x01000013) @
0x00000000dfb2f00
0
ACPI: HPET (v001 INTEL  S5000PSL 0x00000001 INTL 0x01000013) @
0x00000000dfb2e00
0
ACPI: MCFG (v001 INTEL  S5000PSL 0x00000001 INTL 0x01000013) @
0x00000000dfb2d00
0
ACPI: SSDT (v002 INTEL  EIST     0x00004000 INTL 0x01000013) @
0x00000000dfb2c00
0
ACPI: SSDT (v002 INTEL  IPMI     0x00004000 INTL 0x01000013) @
0x00000000dfb2b00
0
ACPI: DSDT (v002 INTEL  S5000PSL 0x00000001 INTL 0x01000013) @
0x000000000000000
0
No NUMA configuration found
Faking a node at 0000000000000000-0000000120000000
Bootmem setup node 0 0000000000000000-0000000120000000
Memory for crash kernel (0x0 to 0x0) notwithin permissible range
disabling kdump
On node 0 totalpages: 1029689
  DMA zone: 2708 pages, LIFO batch:0
  DMA32 zone: 897701 pages, LIFO batch:31
  Normal zone: 129280 pages, LIFO batch:31
ACPI: PM-Timer IO Port: 0x408
ACPI: Local APIC address 0xfee00000
ACPI: LAPIC (acpi_id[0x00] lapic_id[0x00] enabled)
Processor #0 6:15 APIC version 20
ACPI: LAPIC (acpi_id[0x01] lapic_id[0x02] enabled)
Processor #2 6:15 APIC version 20
ACPI: LAPIC (acpi_id[0x02] lapic_id[0x01] enabled)
Processor #1 6:15 APIC version 20
ACPI: LAPIC (acpi_id[0x03] lapic_id[0x03] enabled)
Processor #3 6:15 APIC version 20
ACPI: LAPIC (acpi_id[0x04] lapic_id[0x84] disabled)
ACPI: LAPIC (acpi_id[0x05] lapic_id[0x85] disabled)
ACPI: LAPIC (acpi_id[0x06] lapic_id[0x86] disabled)
ACPI: LAPIC (acpi_id[0x07] lapic_id[0x87] disabled)
ACPI: LAPIC_NMI (acpi_id[0x00] high level lint[0x1])
ACPI: LAPIC_NMI (acpi_id[0x01] high level lint[0x1])
ACPI: LAPIC_NMI (acpi_id[0x02] high level lint[0x1])
ACPI: LAPIC_NMI (acpi_id[0x03] high level lint[0x1])
ACPI: LAPIC_NMI (acpi_id[0x04] high level lint[0x1])
ACPI: LAPIC_NMI (acpi_id[0x05] high level lint[0x1])
ACPI: LAPIC_NMI (acpi_id[0x06] high level lint[0x1])
ACPI: LAPIC_NMI (acpi_id[0x07] high level lint[0x1])
ACPI: IOAPIC (id[0x08] address[0xfec00000] gsi_base[0])
IOAPIC[0]: apic_id 8, version 32, address 0xfec00000, GSI 0-23
ACPI: IOAPIC (id[0x09] address[0xfec80000] gsi_base[24])
IOAPIC[1]: apic_id 9, version 32, address 0xfec80000, GSI 24-47
ACPI: INT_SRC_OVR (bus 0 bus_irq 0 global_irq 2 dfl dfl)
ACPI: INT_SRC_OVR (bus 0 bus_irq 9 global_irq 9 high level)
ACPI: IRQ0 used by override.
ACPI: IRQ2 used by override.
ACPI: IRQ9 used by override.
Setting APIC routing to physical flat
ACPI: HPET id: 0x8086a201 base: 0xfed00000
Using ACPI (MADT) for SMP configuration information
Nosave address range: 000000000009f000 - 00000000000a0000
Nosave address range: 00000000000a0000 - 0000000000100000
Nosave address range: 00000000de2bd000 - 00000000de37c000
Nosave address range: 00000000dfa42000 - 00000000dfa9a000
Nosave address range: 00000000dfaad000 - 00000000dfb1a000
Nosave address range: 00000000dfb2b000 - 00000000dfb3a000
Nosave address range: 00000000dfc00000 - 00000000f0000000
Nosave address range: 00000000f0000000 - 00000000ffc00000
Nosave address range: 00000000ffc00000 - 00000000ffc0c000
Nosave address range: 00000000ffc0c000 - 0000000100000000
Allocating PCI resources starting at f1000000 (gap: f0000000:fc00000)
SMP: Allowing 8 CPUs, 4 hotplug CPUs
Built 1 zonelists.  Total pages: 1029689
Kernel command line: ro root=/dev/VolGroup00/LogVol00 rhgb quiet
Initializing CPU#0
PID hash table entries: 4096 (order: 12, 32768 bytes)
Console: colour VGA+ 80x25
Dentry cache hash table entries: 524288 (order: 10, 4194304 bytes)
Inode-cache hash table entries: 262144 (order: 9, 2097152 bytes)
Checking aperture...
PCI-DMA: Using software bounce buffering for IO (SWIOTLB)
Placing software IO TLB between 0x165b000 - 0x565b000
Memory: 4042892k/4718592k available (2434k kernel code, 145316k reserved,
1235k
data, 192k init)
Calibrating delay using timer specific routine.. 5323.65 BogoMIPS
(lpj=2661825)
Security Framework v1.0.0 initialized
SELinux:  Initializing.
SELinux:  Starting in permissive mode
selinux_register_security:  Registering secondary module capability
Capability LSM initialized as secondary
Mount-cache hash table entries: 256
CPU: L1 I cache: 32K, L1 D cache: 32K
CPU: L2 cache: 4096K
using mwait in idle threads.
CPU: Physical Processor ID: 0
CPU: Processor Core ID: 0
CPU0: Thermal monitoring enabled (TM2)
SMP alternatives: switching to UP code
ACPI: Core revision 20060707
Using local APIC timer interrupts.
result 20781330
Detected 20.781 MHz APIC timer.
SMP alternatives: switching to SMP code
Booting processor 1/4 APIC 0x2
Initializing CPU#1
Calibrating delay using timer specific routine.. 5320.01 BogoMIPS
(lpj=2660009)
CPU: L1 I cache: 32K, L1 D cache: 32K
CPU: L2 cache: 4096K
CPU: Physical Processor ID: 0
CPU: Processor Core ID: 2
CPU1: Thermal monitoring enabled (TM2)
Intel(R) Xeon(R) CPU           X5355  @ 2.66GHz stepping 07
SMP alternatives: switching to SMP code
Booting processor 2/4 APIC 0x1
Initializing CPU#2
Calibrating delay using timer specific routine.. 5320.03 BogoMIPS
(lpj=2660018)
CPU: L1 I cache: 32K, L1 D cache: 32K
CPU: L2 cache: 4096K
CPU: Physical Processor ID: 0
CPU: Processor Core ID: 1
CPU2: Thermal monitoring enabled (TM2)
Intel(R) Xeon(R) CPU           X5355  @ 2.66GHz stepping 07
SMP alternatives: switching to SMP code
Booting processor 3/4 APIC 0x3
Initializing CPU#3
Calibrating delay using timer specific routine.. 5320.01 BogoMIPS
(lpj=2660005)
CPU: L1 I cache: 32K, L1 D cache: 32K
CPU: L2 cache: 4096K
CPU: Physical Processor ID: 0
CPU: Processor Core ID: 3
CPU3: Thermal monitoring enabled (TM2)
Intel(R) Xeon(R) CPU           X5355  @ 2.66GHz stepping 07
Brought up 4 CPUs
testing NMI watchdog ... OK.
time.c: Using 14.318180 MHz WALL HPET GTOD HPET/TSC timer.
time.c: Detected 2660.011 MHz processor.
sizeof(vma)=176 bytes
sizeof(page)=56 bytes
sizeof(inode)=560 bytes
sizeof(dentry)=216 bytes
sizeof(ext3inode)=760 bytes
sizeof(buffer_head)=96 bytes
sizeof(skbuff)=240 bytes
migration_cost=40,7756
checking if image is initramfs... it is
Freeing initrd memory: 3078k freed
NET: Registered protocol family 16
ACPI: bus type pci registered
PCI: Using MMCONFIG at e0000000
ACPI: Interpreter enabled
ACPI: Using IOAPIC for interrupt routing
ACPI: PCI Root Bridge [PCI0] (0000:00)
PCI: Probing PCI hardware (bus 00)
PCI: Ignoring BAR0-3 of IDE controller 0000:00:1f.1
Boot video device is 0000:0d:0c.0
PCI: Transparent bridge - 0000:00:1e.0
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0._PRT]
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.PC32._PRT]
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.PEX0._PRT]
ACPI: PCI Interrupt Link [LNKA] (IRQs 5 7 *10 11)
ACPI: PCI Interrupt Link [LNKB] (IRQs 5 7 10 *11)
ACPI: PCI Interrupt Link [LNKC] (IRQs *5 7 10 11)
ACPI: PCI Interrupt Link [LNKD] (IRQs 5 7 10 *11)
ACPI: PCI Interrupt Link [LNKE] (IRQs 5 7 *10 11)
ACPI: PCI Interrupt Link [LNKF] (IRQs 5 7 10 *11)
ACPI: PCI Interrupt Link [LNKG] (IRQs *5 7 10 11)
ACPI: PCI Interrupt Link [LNKH] (IRQs 5 7 10 *11)
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.PCIE._PRT]
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.PCIE.PCIX._PRT]
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.PCIE.PCIW._PRT]
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.PCIE.PCIW.PCIO._PRT]
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.PCIE.PCIW.PCIP._PRT]
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.PCIE.PCIW.PCIQ._PRT]
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.PCIF._PRT]
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.PCIG._PRT]
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.PCIH._PRT]
Linux Plug and Play Support v0.97 (c) Adam Belay
pnp: PnP ACPI init
pnp: PnP ACPI: found 14 devices
usbcore: registered new driver usbfs
usbcore: registered new driver hub
PCI: Using ACPI for IRQ routing
PCI: If a device doesn't work, try "pci=routeirq".  If it helps, post a
report
NetLabel: Initializing
NetLabel:  domain hash size = 128
NetLabel:  protocols = UNLABELED CIPSOv4
NetLabel:  unlabeled traffic allowed by default
hpet0: at MMIO 0xfed00000 (virtual 0xffffffffff5fe000), IRQs 2, 8, 0
hpet0: 3 64-bit timers, 14318180 Hz
PCI-GART: No AMD northbridge found.
pnp: 00:06: ioport range 0x500-0x53f has been reserved
pnp: 00:06: ioport range 0x400-0x47f could not be reserved
pnp: 00:06: ioport range 0x800-0x87f could not be reserved
PCI: Bridge: 0000:02:00.0
  IO window: disabled.
  MEM window: disabled.
  PREFETCH window: disabled.
PCI: Bridge: 0000:02:01.0
  IO window: disabled.
  MEM window: disabled.
  PREFETCH window: disabled.
PCI: Bridge: 0000:02:02.0
  IO window: 3000-3fff
  MEM window: fa000000-fa8fffff
  PREFETCH window: disabled.
PCI: Bridge: 0000:01:00.0
  IO window: 3000-3fff
  MEM window: fa000000-fa8fffff
  PREFETCH window: disabled.
PCI: Bridge: 0000:01:00.3
  IO window: disabled.
  MEM window: disabled.
  PREFETCH window: disabled.
PCI: Bridge: 0000:00:02.0
  IO window: 3000-3fff
  MEM window: fa000000-fa9fffff
  PREFETCH window: disabled.
PCI: Bridge: 0000:00:03.0
  IO window: disabled.
  MEM window: disabled.
  PREFETCH window: disabled.
PCI: Bridge: 0000:00:04.0
  IO window: disabled.
  MEM window: disabled.
  PREFETCH window: disabled.
PCI: Bridge: 0000:00:05.0
  IO window: disabled.
  MEM window: disabled.
  PREFETCH window: disabled.
PCI: Bridge: 0000:00:06.0
  IO window: disabled.
  MEM window: disabled.
  PREFETCH window: disabled.
PCI: Bridge: 0000:00:07.0
  IO window: disabled.
  MEM window: disabled.
  PREFETCH window: disabled.
PCI: Bridge: 0000:00:1c.0
  IO window: 2000-2fff
  MEM window: fab00000-fabfffff
  PREFETCH window: f8000000-f9ffffff
PCI: Bridge: 0000:00:1e.0
  IO window: 1000-1fff
  MEM window: faa00000-faafffff
  PREFETCH window: f0000000-f7ffffff
GSI 16 sharing vector 0xA9 and IRQ 16
ACPI: PCI Interrupt 0000:00:02.0[A] -> GSI 16 (level, low) -> IRQ 169
PCI: Setting latency timer of device 0000:00:02.0 to 64
ACPI: PCI Interrupt 0000:01:00.0[A] -> GSI 16 (level, low) -> IRQ 169
PCI: Setting latency timer of device 0000:01:00.0 to 64
ACPI: PCI Interrupt 0000:02:00.0[A] -> GSI 16 (level, low) -> IRQ 169
PCI: Setting latency timer of device 0000:02:00.0 to 64
GSI 17 sharing vector 0xB1 and IRQ 17
ACPI: PCI Interrupt 0000:02:01.0[A] -> GSI 17 (level, low) -> IRQ 177
PCI: Setting latency timer of device 0000:02:01.0 to 64
GSI 18 sharing vector 0xB9 and IRQ 18
ACPI: PCI Interrupt 0000:02:02.0[A] -> GSI 18 (level, low) -> IRQ 185
PCI: Setting latency timer of device 0000:02:02.0 to 64
PCI: Setting latency timer of device 0000:01:00.3 to 64
ACPI: PCI Interrupt 0000:00:03.0[A] -> GSI 16 (level, low) -> IRQ 169
PCI: Setting latency timer of device 0000:00:03.0 to 64
ACPI: PCI Interrupt 0000:00:04.0[A] -> GSI 16 (level, low) -> IRQ 169
PCI: Setting latency timer of device 0000:00:04.0 to 64
ACPI: PCI Interrupt 0000:00:05.0[A] -> GSI 16 (level, low) -> IRQ 169
PCI: Setting latency timer of device 0000:00:05.0 to 64
ACPI: PCI Interrupt 0000:00:06.0[A] -> GSI 16 (level, low) -> IRQ 169
PCI: Setting latency timer of device 0000:00:06.0 to 64
ACPI: PCI Interrupt 0000:00:07.0[A] -> GSI 16 (level, low) -> IRQ 169
PCI: Setting latency timer of device 0000:00:07.0 to 64
ACPI: PCI Interrupt 0000:00:1c.0[A] -> GSI 16 (level, low) -> IRQ 169
PCI: Setting latency timer of device 0000:00:1c.0 to 64
PCI: Setting latency timer of device 0000:00:1e.0 to 64
NET: Registered protocol family 2
IP route cache hash table entries: 131072 (order: 8, 1048576 bytes)
TCP established hash table entries: 262144 (order: 10, 4194304 bytes)
TCP bind hash table entries: 65536 (order: 8, 1048576 bytes)
TCP: Hash tables configured (established 262144 bind 65536)
TCP reno registered
audit: initializing netlink socket (disabled)
audit(1198044137.617:1): initialized
Total HugeTLB memory allocated, 0
VFS: Disk quotas dquot_6.5.1
Dquot-cache hash table entries: 512 (order 0, 4096 bytes)
SELinux:  Registering netfilter hooks
Initializing Cryptographic API
ksign: Installing public key data
Loading keyring
- Added public key F3B7045D54802500
- User ID: Red Hat, Inc. (Kernel Module GPG key)
io scheduler noop registered
io scheduler anticipatory registered
io scheduler deadline registered
io scheduler cfq registered (default)
PCI: Setting latency timer of device 0000:00:02.0 to 64
assign_interrupt_mode Found MSI capability
Allocate Port Service[0000:00:02.0:pcie00]
Allocate Port Service[0000:00:02.0:pcie01]
PCI: Setting latency timer of device 0000:00:03.0 to 64
assign_interrupt_mode Found MSI capability
Allocate Port Service[0000:00:03.0:pcie00]
Allocate Port Service[0000:00:03.0:pcie01]
PCI: Setting latency timer of device 0000:00:04.0 to 64
assign_interrupt_mode Found MSI capability
Allocate Port Service[0000:00:04.0:pcie00]
Allocate Port Service[0000:00:04.0:pcie01]
PCI: Setting latency timer of device 0000:00:05.0 to 64
assign_interrupt_mode Found MSI capability
Allocate Port Service[0000:00:05.0:pcie00]
Allocate Port Service[0000:00:05.0:pcie01]
PCI: Setting latency timer of device 0000:00:06.0 to 64
assign_interrupt_mode Found MSI capability
Allocate Port Service[0000:00:06.0:pcie00]
Allocate Port Service[0000:00:06.0:pcie01]
PCI: Setting latency timer of device 0000:00:07.0 to 64
assign_interrupt_mode Found MSI capability
Allocate Port Service[0000:00:07.0:pcie00]
Allocate Port Service[0000:00:07.0:pcie01]
PCI: Setting latency timer of device 0000:00:1c.0 to 64
assign_interrupt_mode Found MSI capability
Allocate Port Service[0000:00:1c.0:pcie00]
Allocate Port Service[0000:00:1c.0:pcie02]
Allocate Port Service[0000:00:1c.0:pcie03]
PCI: Setting latency timer of device 0000:01:00.0 to 64
Allocate Port Service[0000:01:00.0:pcie10]
Allocate Port Service[0000:01:00.0:pcie11]
PCI: Setting latency timer of device 0000:02:00.0 to 64
assign_interrupt_mode Found MSI capability
Allocate Port Service[0000:02:00.0:pcie20]
Allocate Port Service[0000:02:00.0:pcie21]
PCI: Setting latency timer of device 0000:02:01.0 to 64
assign_interrupt_mode Found MSI capability
Allocate Port Service[0000:02:01.0:pcie20]
Allocate Port Service[0000:02:01.0:pcie21]
PCI: Setting latency timer of device 0000:02:02.0 to 64
assign_interrupt_mode Found MSI capability
Allocate Port Service[0000:02:02.0:pcie20]
Allocate Port Service[0000:02:02.0:pcie21]
pci_hotplug: PCI Hot Plug PCI Core version: 0.5
ACPI: CPU0 (power states: C1[C1] C2[C2])
ACPI: Processor [CPU0] (supports 8 throttling states)
ACPI: CPU1 (power states: C1[C1] C2[C2])
ACPI: Processor [CPU1] (supports 8 throttling states)
ACPI: CPU2 (power states: C1[C1] C2[C2])
ACPI: Processor [CPU2] (supports 8 throttling states)
ACPI: CPU3 (power states: C1[C1] C2[C2])
ACPI: Processor [CPU3] (supports 8 throttling states)
ACPI Exception (acpi_processor-0681): AE_NOT_FOUND, Processor Device is not
pres
ent [20060707]
ACPI: Getting cpuindex for acpiid 0x4
ACPI Exception (acpi_processor-0681): AE_NOT_FOUND, Processor Device is not
pres
ent [20060707]
ACPI: Getting cpuindex for acpiid 0x5
ACPI Exception (acpi_processor-0681): AE_NOT_FOUND, Processor Device is not
pres
ent [20060707]
ACPI: Getting cpuindex for acpiid 0x6
ACPI Exception (acpi_processor-0681): AE_NOT_FOUND, Processor Device is not
pres
ent [20060707]
ACPI: Getting cpuindex for acpiid 0x7
Real Time Clock Driver v1.12ac
hpet_resources: 0xfed00000 is busy
Non-volatile memory driver v1.2
Linux agpgart interface v0.101 (c) Dave Jones
Serial: 8250/16550 driver $Revision: 1.90 $ 4 ports, IRQ sharing enabled
serial8250: ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A
serial8250: ttyS1 at I/O 0x2f8 (irq = 3) is a 16550A
00:09: ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A
00:0a: ttyS1 at I/O 0x2f8 (irq = 3) is a 16550A
RAMDISK driver initialized: 16 RAM disks of 16384K size 4096 blocksize
Uniform Multi-Platform E-IDE driver Revision: 7.00alpha2
ide: Assuming 33MHz system bus speed for PIO modes; override with idebus=xx
ESB2: IDE controller at PCI slot 0000:00:1f.1
GSI 19 sharing vector 0x5A and IRQ 19
ACPI: PCI Interrupt 0000:00:1f.1[A] -> GSI 20 (level, low) -> IRQ 90
ESB2: chipset revision 9
ESB2: not 100% native mode: will probe irqs later
    ide0: BM-DMA at 0x40b0-0x40b7, BIOS settings: hda:DMA, hdb:DMA
    ide1: BM-DMA at 0x40b8-0x40bf, BIOS settings: hdc:pio, hdd:pio
Probing IDE interface ide0...
hda: LITE-ON DVDRW LH-20A1P, ATAPI CD/DVD-ROM drive
hdb: LITE-ON DVDRW LH-20A1P, ATAPI CD/DVD-ROM drive
ide0 at 0x1f0-0x1f7,0x3f6 on irq 14
Probing IDE interface ide1...
Probing IDE interface ide1...
ide-floppy driver 0.99.newide
usbcore: registered new driver hiddev
usbcore: registered new driver usbhid
drivers/usb/input/hid-core.c: v2.6:USB HID core driver
PNP: PS/2 Controller [PNP0303:PS2K,PNP0f03:PS2M] at 0x60,0x64 irq 1,12
serio: i8042 KBD port at 0x60,0x64 irq 1
serio: i8042 AUX port at 0x60,0x64 irq 12
mice: PS/2 mouse device common for all mice
md: md driver 0.90.3 MAX_MD_DEVS=256, MD_SB_DISKS=27
md: bitmap version 4.39
TCP bic registered
Initializing IPsec netlink socket
NET: Registered protocol family 1
NET: Registered protocol family 17
ACPI: (supports S0 S1 S3 S4 S5)
Freeing unused kernel memory: 192k freed
Write protecting the kernel read-only data: 468k
input: AT Translated Set 2 keyboard as /class/input/input0
USB Universal Host Controller Interface driver v3.0
GSI 20 sharing vector 0x62 and IRQ 20
ACPI: PCI Interrupt 0000:00:1d.0[A] -> GSI 23 (level, low) -> IRQ 98
PCI: Setting latency timer of device 0000:00:1d.0 to 64
uhci_hcd 0000:00:1d.0: UHCI Host Controller
uhci_hcd 0000:00:1d.0: new USB bus registered, assigned bus number 1
uhci_hcd 0000:00:1d.0: irq 98, io base 0x00004080
usb usb1: configuration #1 chosen from 1 choice
hub 1-0:1.0: USB hub found
hub 1-0:1.0: 2 ports detected
GSI 21 sharing vector 0x6A and IRQ 21
ACPI: PCI Interrupt 0000:00:1d.1[B] -> GSI 22 (level, low) -> IRQ 106
PCI: Setting latency timer of device 0000:00:1d.1 to 64
uhci_hcd 0000:00:1d.1: UHCI Host Controller
uhci_hcd 0000:00:1d.1: new USB bus registered, assigned bus number 2
uhci_hcd 0000:00:1d.1: irq 106, io base 0x00004060
usb usb2: configuration #1 chosen from 1 choice
hub 2-0:1.0: USB hub found
hub 2-0:1.0: 2 ports detected
ACPI: PCI Interrupt 0000:00:1d.2[C] -> GSI 23 (level, low) -> IRQ 98
PCI: Setting latency timer of device 0000:00:1d.2 to 64
uhci_hcd 0000:00:1d.2: UHCI Host Controller
uhci_hcd 0000:00:1d.2: new USB bus registered, assigned bus number 3
uhci_hcd 0000:00:1d.2: irq 98, io base 0x00004040
usb usb3: configuration #1 chosen from 1 choice
hub 3-0:1.0: USB hub found
hub 3-0:1.0: 2 ports detected
ACPI: PCI Interrupt 0000:00:1d.3[D] -> GSI 22 (level, low) -> IRQ 106
PCI: Setting latency timer of device 0000:00:1d.3 to 64
uhci_hcd 0000:00:1d.3: UHCI Host Controller
uhci_hcd 0000:00:1d.3: new USB bus registered, assigned bus number 4
uhci_hcd 0000:00:1d.3: irq 106, io base 0x00004020
usb usb4: configuration #1 chosen from 1 choice
hub 4-0:1.0: USB hub found
hub 4-0:1.0: 2 ports detected
ohci_hcd: 2005 April 22 USB 1.1 'Open' Host Controller (OHCI) Driver (PCI)
ACPI: PCI Interrupt 0000:00:1d.7[A] -> GSI 23 (level, low) -> IRQ 98
PCI: Setting latency timer of device 0000:00:1d.7 to 64
ehci_hcd 0000:00:1d.7: EHCI Host Controller
ehci_hcd 0000:00:1d.7: new USB bus registered, assigned bus number 5
ehci_hcd 0000:00:1d.7: debug port 1
PCI: cache line size of 32 is not supported by device 0000:00:1d.7
ehci_hcd 0000:00:1d.7: irq 98, io mem 0xfac00400
ehci_hcd 0000:00:1d.7: USB 2.0 started, EHCI 1.00, driver 10 Dec 2004
usb usb5: configuration #1 chosen from 1 choice
hub 5-0:1.0: USB hub found
hub 5-0:1.0: 8 ports detected
input: ImPS/2 Logitech Wheel Mouse as /class/input/input1
SCSI subsystem initialized
3ware 9000 Storage Controller device driver for Linux v2.26.02.008.
ACPI: PCI Interrupt 0000:0c:00.0[A] -> GSI 16 (level, low) -> IRQ 169
PCI: Setting latency timer of device 0000:0c:00.0 to 64
scsi0 : 3ware 9000 Storage Controller
3w-9xxx: scsi0: Found a 3ware 9000 Storage Controller at 0xfab00000, IRQ:
169.
3w-9xxx: scsi0: Firmware FE9X 3.08.02.007, BIOS BE9X 3.08.00.002, Ports: 8.
  Vendor: AMCC      Model: 9650SE-8LP DISK   Rev: 3.08
  Type:   Direct-Access                      ANSI SCSI revision: 05
SCSI device sda: 134217727 512-byte hdwr sectors (68719 MB)
sda: Write Protect is off
sda: Mode Sense: 23 00 00 00
SCSI device sda: drive cache: write back, no read (daft)
SCSI device sda: 134217727 512-byte hdwr sectors (68719 MB)
sda: Write Protect is off
sda: Mode Sense: 23 00 00 00
SCSI device sda: drive cache: write back, no read (daft)
 sda: sda1 sda2
sd 0:0:0:0: Attached scsi disk sda
  Vendor: AMCC      Model: 9650SE-8LP DISK   Rev: 3.08
  Type:   Direct-Access                      ANSI SCSI revision: 05
SCSI device sdb: 1330604033 512-byte hdwr sectors (681269 MB)
sdb: Write Protect is off
sdb: Mode Sense: 23 00 00 00
SCSI device sdb: drive cache: write back, no read (daft)
SCSI device sdb: 1330604033 512-byte hdwr sectors (681269 MB)
sdb: Write Protect is off
sdb: Mode Sense: 23 00 00 00
SCSI device sdb: drive cache: write back, no read (daft)
 sdb: sdb1
sd 0:0:0:1: Attached scsi disk sdb
libata version 2.21 loaded.
ata_piix 0000:00:1f.2: version 2.11
ata_piix 0000:00:1f.2: MAP [ P0 P2 P1 P3 ]
ACPI: PCI Interrupt 0000:00:1f.2[B] -> GSI 20 (level, low) -> IRQ 90
PCI: Setting latency timer of device 0000:00:1f.2 to 64
scsi1 : ata_piix
scsi2 : ata_piix
ata1: SATA max UDMA/133 cmd 0x00000000000140c8 ctl 0x00000000000140e6 bmdma
0x00
000000000140a0 irq 90
ata2: SATA max UDMA/133 cmd 0x00000000000140c0 ctl 0x00000000000140e2 bmdma
0x00
000000000140a8 irq 90
ata1.00: ATAPI, max UDMA/100
ata1.00: applying bridge limits
ata1.00: configured for UDMA/100
  Vendor: SONY      Model: SDX-570V          Rev: 0100
  Type:   Sequential-Access                  ANSI SCSI revision: 02
device-mapper: ioctl: 4.11.0-ioctl (2006-09-14) initialised:
dm-devel redhat com
kjournald starting.  Commit interval 5 seconds
EXT3-fs: mounted filesystem with ordered data mode.
SELinux:  Disabled at runtime.
SELinux:  Unregistering netfilter hooks
audit(1198044145.914:2): selinux=0 auid=4294967295
input: PC Speaker as /class/input/input2
sd 0:0:0:0: Attached scsi generic sg0 type 0
sd 0:0:0:1: Attached scsi generic sg1 type 0
scsi 1:0:0:0: Attached scsi generic sg2 type 1
shpchp: Standard Hot Plug PCI Controller Driver version: 0.4
Intel(R) PRO/1000 Network Driver - version 7.3.20-k2-NAPI
Copyright (c) 1999-2006 Intel Corporation.
ACPI: PCI Interrupt 0000:05:00.0[A] -> GSI 18 (level, low) -> IRQ 185
PCI: Setting latency timer of device 0000:05:00.0 to 64
e1000: 0000:05:00.0: e1000_probe: (PCI Express:2.5Gb/s:32-bit)
00:15:17:30:2b:38
e1000: eth0: e1000_probe: Intel(R) PRO/1000 Network Connection
GSI 22 sharing vector 0x72 and IRQ 22
ACPI: PCI Interrupt 0000:05:00.1[B] -> GSI 19 (level, low) -> IRQ 114
PCI: Setting latency timer of device 0000:05:00.1 to 64
e1000: 0000:05:00.1: e1000_probe: (PCI Express:2.5Gb/s:32-bit)
00:15:17:30:2b:39
hda: ATAPI 48X DVD-ROM DVD-R-RAM CD-R/RW drive, 2048kB Cache, UDMA(66)
Uniform CD-ROM driver Revision: 3.20
intel_rng: Firmware space is locked read-only. <4>intel_rng: If you can't or
 don't want to <4>intel_rng: disable this in firmware setup, and
<4>intel_rng: i
f
 you are certain that your <4>intel_rng: system has a functional
 RNG, try<4>intel_rng: using the 'no_fwh_detect' option.
hdb: ATAPI 48X DVD-ROM DVD-R-RAM CD-R/RW drive, 2048kB Cache, UDMA(66)
e1000: eth1: e1000_probe: Intel(R) PRO/1000 Network Connection
ACPI: PCI Interrupt 0000:00:1f.3[B] -> GSI 20 (level, low) -> IRQ 90
st: Version 20050830, fixed bufsize 32768, s/g segs 256
st 1:0:0:0: Attached scsi tape st0
st0: try direct i/o: yes (alignment 512 B)
floppy0: no floppy controllers found
lp: driver loaded but no devices found
NET: Registered protocol family 10
lo: Disabled Privacy Extensions
IPv6 over IPv4 tunneling driver
ACPI: Power Button (FF) [PWRF]
ACPI: Sleep Button (CM) [SLPB]
ACPI: Power Button (CM) [PWRB]
ibm_acpi: ec object not found
md: Autodetecting RAID arrays.
md: autorun ...
md: ... autorun DONE.
device-mapper: multipath: version 1.0.5 loaded
EXT3 FS on dm-0, internal journal
kjournald starting.  Commit interval 5 seconds
EXT3 FS on sda1, internal journal
EXT3-fs: mounted filesystem with ordered data mode.
kjournald starting.  Commit interval 5 seconds
EXT3 FS on sdb1, internal journal
EXT3-fs: mounted filesystem with ordered data mode.
Adding 2031608k swap on /dev/VolGroup00/LogVol01.  Priority:-1 extents:1
across:
2031608k
[root nedrhealy log]#



[Date Prev][Date Next]   [Thread Prev][Thread Next]   [Thread Index] [Date Index] [Author Index]