[rhn-users] qlogic 2300 attached luns not enabled with 2.4.21-32.EL

[Ray Stell]

After an recent download of kernel update vmlinuz-2.4.21-32.EL
the qlogic attached luns will not retain an enabled status 
on reboot.  This was not true with the last kernel, vmlinuz-2.4.21-27.0.4.EL.
I'm trying to use the built into redhat qla2300.o.

I can enable the luns with qlogic software and they work, but
the config does not survive a reboot.  I've created a new
initrd with the modules.conf and the disks enabled, but
the OS scsi mapping to the qlogic card does not show up
in messages.  If I boot the old kernel the luns come up. 

Is there something else I have to do to make the mapping persistant.

Old (working) /var/log/messages lines:

May 19 15:47:21 pecan kernel: scsi(0): Found a QLA2312  @ bus 1, device 0xa, irq 11, iobase 0xf88dd000
May 19 15:47:21 pecan kernel: scsi(0): 32 Bit PCI Addressing Enabled.
May 19 15:47:21 pecan kernel: scsi(0): Configure NVRAM parameters...
May 19 15:47:21 pecan kernel: scsi(0): Verifying loaded RISC code...
May 19 15:47:21 pecan kernel: scsi(0): Verifying chip...
May 19 15:47:21 pecan kernel: scsi(0): Waiting for LIP to complete...
May 19 15:47:21 pecan kernel: scsi(0): LOOP UP detected.
May 19 15:47:21 pecan kernel: scsi(0): Port database changed.
May 19 15:47:21 pecan kernel: scsi(0): Topology - (F_Port), Host Loop address 0xffff
May 19 15:47:21 pecan kernel: scsi-qla0-adapter-node=200000e08b0a8deb\;
May 19 15:47:21 pecan kernel: scsi-qla0-adapter-port=210000e08b0a8deb\;
May 19 15:47:21 pecan kernel: scsi-qla0-tgt-0-di-0-port=5005076300c89456\;
May 19 15:47:21 pecan kernel: scsi-qla0-tgt-1-di-0-port=5005076300c49456\;
May 19 15:47:21 pecan kernel: scsi0 : QLogic QLA2312 PCI to Fibre Channel Host Adapter: bus 1 device 10 irq 11
May 19 15:47:21 pecan kernel: scsi(0:0:0:0): Enabled tagged queuing, queue depth 32.
May 19 15:47:21 pecan kernel: scsi(0:0:0:1): Enabled tagged queuing, queue depth 32.
May 19 15:47:21 pecan kernel: scsi(0:0:1:0): Enabled tagged queuing, queue depth 32.
May 19 15:47:21 pecan kernel: scsi(0:0:1:1): Enabled tagged queuing, queue depth 32.
May 19 15:47:21 pecan kernel: Attached scsi disk sda at scsi0, channel 0, id 0, lun 0
May 19 15:47:21 pecan kernel: Attached scsi disk sdb at scsi0, channel 0, id 0, lun 1
May 19 15:47:22 pecan kernel: Attached scsi disk sdc at scsi0, channel 0, id 1, lun 0
May 19 15:47:22 pecan kernel: Attached scsi disk sdd at scsi0, channel 0, id 1, lun 1
May 19 15:47:22 pecan kernel: scsi(0) qla2x00_isr MBA_PORT_UPDATE ignored
May 19 15:47:22 pecan kernel: scsi(0) qla2x00_isr MBA_PORT_UPDATE ignored

new (broken) /var/log/messages lines:

May 24 14:53:45 pecan kernel: scsi(0): Found a QLA2312  @ bus 1, device 0xa, irq 11, iobase 0xf88de000
May 24 14:53:45 pecan kernel: scsi(0): 32 Bit PCI Addressing Enabled.
May 24 14:53:45 pecan kernel: scsi(0): Configure NVRAM parameters...
May 24 14:53:45 pecan kernel: scsi(0): Verifying loaded RISC code...
May 24 14:53:45 pecan kernel: scsi(0): Verifying chip...
May 24 14:53:45 pecan kernel: scsi(0): Waiting for LIP to complete...
May 24 14:53:45 pecan kernel: scsi(0): LOOP UP detected.
May 24 14:53:45 pecan kernel: scsi(0): Port database changed.
May 24 14:53:45 pecan kernel: scsi(0): Topology - (F_Port), Host Loop address 0xffff
May 24 14:53:45 pecan kernel: scsi-qla0-adapter-node=200000e08b0a8deb\;
May 24 14:53:45 pecan kernel: scsi-qla0-adapter-port=210000e08b0a8deb\;
May 24 14:53:45 pecan kernel: scsi0 : QLogic QLA2312 PCI to Fibre Channel Host Adapter: bus 1 device 10 irq 11
May 24 14:53:45 pecan kernel: scsi(0) qla2x00_isr MBA_PORT_UPDATE ignored
May 24 14:53:45 pecan kernel: scsi(0) qla2x00_isr MBA_PORT_UPDATE ignored
============================================================
Ray Stell  stellr at vt.edu  (540) 231-4109  Tempus fugit  28^D